TV REPAIR TIPS PAGE 22

MAKE	MODEL	CHASSIS	SYMPTOM	CURE
SHARP	19NP48	N/A	CO-CHANNEL INTERFERENCE	CHECK/REPLACE ANTENNA BLOCK (RUNTK0371CEZZ)
SHARP	19NP48	N/A	CO-CHANNEL INTERFERENCE	REPLACE ANTENNA BLOCK (P/N # RUNTK0371CEZZ)
SHARP	19NP58	N/A	CO-CHANNEL INTERFERENCE	CHECK/REPLACE ANTENNA BLOCK (RUNTK0371CEZZ)
SHARP	19NP58	N/A	REGULATOR WON'T START UP	CHECK D705,R702,IC701
SHARP	19NP58	N/A	CO-CHANNEL INTERFERENCE	REPLACE ANTENNA BLOCK (P/N # RUNTK0371CEZZ)
SHARP	19NP58	N/A	ONLY SNOW ON SCREEN-WILL NOT TUNE A CHANNEL	CHECK IC1401 (UPC1486C)
SHARP	19NP58	N/A	DEAD SET	CHECK D701-D704,R701
SHARP	19NP88	N/A	DEAD SET	CHECK D701-D704,R701
SHARP	19NP88	N/A	ONLY SNOW ON SCREEN-WILL NOT TUNE A CHANNEL	CHECK IC1401 (UPC1486C)
SHARP	19NP88	N/A	REGULATOR WON'T START UP	CHECK D705,R702,IC701
SHARP	19NV10	N/A	CO-CHANNEL INTERFERENCE	REPLACE ANTENNA BLOCK (P/N # RUNTK0371CEZZ)
SHARP	19NV10	N/A	CO-CHANNEL INTERFERENCE	CHECK/REPLACE ANTENNA BLOCK (RUNTK0371CEZZ)
SHARP	19NV68	N/A	CO-CHANNEL INTERFERENCE	REPLACE ANTENNA BLOCK (P/N # RUNTK0371CEZZ)
SHARP	19NV68	N/A	CO-CHANNEL INTERFERENCE	CHECK/REPLACE ANTENNA BLOCK (RUNTK0371CEZZ)
SHARP	19NV88	N/A	CO-CHANNEL INTERFERENCE	REPLACE ANTENNA BLOCK (P/N # RUNTK0371CEZZ)
SHARP	19NV88	N/A	CO-CHANNEL INTERFERENCE	CHECK/REPLACE ANTENNA BLOCK (RUNTK0371CEZZ)
SHARP	19RP519	N/A	REGULATOR WON'T START UP	CHECK D705,R702,IC701
SHARP	19RP519	N/A	CO-CHANNEL INTERFERENCE	CHECK/REPLACE ANTENNA BLOCK (RUNTK0371CEZZ)
SHARP	19RP519	N/A	CO-CHANNEL INTERFERENCE	REPLACE ANTENNA BLOCK (P/N # RUNTK0371CEZZ)
SHARP	19RP519	N/A	NO SOUND	CHECK/REPLACE IC201
SHARP	19RP519	N/A	ONLY SNOW ON SCREEN-WILL NOT TUNE A CHANNEL	CHECK IC1401 (UPC1486C)
SHARP	19RP519	N/A	BRIGHT PICTURE WITH RETRACE LINES	CHECK/REPLACE Q403 FOR SHORT
SHARP	19RP519	N/A	NO COLOR BUT MAY HAVE VERY WEAK COLOR BARS	CHECK/REPLACE C809 (TRIMMER CAPACITOR FOR 3.58MHz ADJUST)
SHARP	19RP519	N/A	DEAD SET	CHECK D701-D704,R701
SHARP	19RP59	N/A	BRIGHT PICTURE WITH RETRACE LINES	CHECK/REPLACE Q403 FOR SHORT
SHARP	19RP59	N/A	ONLY SNOW ON SCREEN-WILL NOT TUNE A CHANNEL	CHECK IC1401 (UPC1486C)
SHARP	19RP59	N/A	CO-CHANNEL INTERFERENCE	REPLACE ANTENNA BLOCK (P/N # RUNTK0371CEZZ)
SHARP	19RP59	N/A	CO-CHANNEL INTERFERENCE	CHECK/REPLACE ANTENNA BLOCK (RUNTK0371CEZZ)
SHARP	19RP59	N/A	NO COLOR BUT MAY HAVE VERY WEAK COLOR BARS	CHECK/REPLACE C809 (TRIMMER CAPACITOR FOR 3.58MHz ADJUST)
SHARP	19RP59	N/A	REGULATOR WON'T START UP	CHECK D705,R702,IC701
SHARP	19RP59	N/A	DEAD SET	CHECK D701-D704,R701
SHARP	19RP59	N/A	NO SOUND	CHECK/REPLACE IC201
SHARP	19RV23	N/A	CO-CHANNEL INTERFERENCE	CHECK/REPLACE ANTENNA BLOCK (RUNTK0371CEZZ)
SHARP	19RV23	N/A	CO-CHANNEL INTERFERENCE	REPLACE ANTENNA BLOCK (P/N # RUNTK0371CEZZ)
SHARP	19RV629	N/A	CO-CHANNEL INTERFERENCE	CHECK/REPLACE ANTENNA BLOCK (RUNTK0371CEZZ)
SHARP	19RV629	N/A	CO-CHANNEL INTERFERENCE	REPLACE ANTENNA BLOCK (P/N # RUNTK0371CEZZ)
SHARP	19RV69	N/A	CO-CHANNEL INTERFERENCE	REPLACE ANTENNA BLOCK (P/N # RUNTK0371CEZZ)
SHARP	19RV69	N/A	NO COLOR BUT MAY HAVE VERY WEAK COLOR BARS	CHECK/REPLACE C809 (TRIMMER CAPACITOR FOR 3.58MHz ADJUST)
SHARP	19RV69	N/A	CO-CHANNEL INTERFERENCE	CHECK/REPLACE ANTENNA BLOCK (RUNTK0371CEZZ)
SHARP	19RV69P	N/A	DISTORTED AUDIO AFTER WARM UP	REPLACE RH-IX1190CEZZ IC (SIGNAL PROCESSOR)
SHARP	19RV79	N/A	CO-CHANNEL INTERFERENCE	CHECK/REPLACE ANTENNA BLOCK (RUNTK0371CEZZ)
SHARP	19RV79	N/A	CO-CHANNEL INTERFERENCE	REPLACE ANTENNA BLOCK (P/N # RUNTK0371CEZZ)
SHARP	19SB60	N/A	CO-CHANNEL INTERFERENCE	REPLACE ANTENNA BLOCK (P/N # RUNTK0371CEZZ)
SHARP	19SB60B	N/A	NO SOUND	CHECK/REPLACE R3206 FOR OPEN
SHARP	19SB610	N/A	CO-CHANNEL INTERFERENCE	REPLACE ANTENNA BLOCK (P/N # RUNTK0371CEZZ)
SHARP	19SB620	N/A	CO-CHANNEL INTERFERENCE	REPLACE ANTENNA BLOCK (P/N # RUNTK0371CEZZ)
SHARP	19SB620B	N/A	DEAD SET	CHECK/REPLACE D701/R701 (2.7 @ 7W)
SHARP	19SB620B	N/A	NO SOUND	CHECK/REPLACE R3206 FOR OPEN
SHARP	19SB640	N/A	CO-CHANNEL INTERFERENCE	REPLACE ANTENNA BLOCK (P/N # RUNTK0371CEZZ)
SHARP	19SB640B	N/A	NO SOUND	CHECK/REPLACE R3206 FOR OPEN
SHARP	19SB70	N/A	CO-CHANNEL INTERFERENCE	CHECK/REPLACE ANTENNA BLOCK (RUNTK0371CEZZ)
SHARP	19SB70	N/A	CO-CHANNEL INTERFERENCE	REPLACE ANTENNA BLOCK (P/N # RUNTK0371CEZZ)
SHARP	19TB30	N/A	CO-CHANNEL INTERFERENCE	REPLACE ANTENNA BLOCK (P/N # RUNTK0371CEZZ)
SHARP	19TB30	N/A	CO-CHANNEL INTERFERENCE	CHECK/REPLACE ANTENNA BLOCK (RUNTK0371CEZZ)
SHARP	19TB33	N/A	CO-CHANNEL INTERFERENCE	REPLACE ANTENNA BLOCK (P/N # RUNTK0371CEZZ)
SHARP	19TB33	N/A	CO-CHANNEL INTERFERENCE	CHECK/REPLACE ANTENNA BLOCK (RUNTK0371CEZZ)
SHARP	20AM100	N/A	VENETIAN BLIND EFFECT - HORZ. BARS ACROSS SCREEN	CHECK/REPLACE IC4201 (P/N# RH-IX1705CEZZ)
SHARP	20AM100	N/A	CO-CHANNEL INTERFERENCE	REPLACE ANTENNA BLOCK (P/N # RUNTK0371CEZZ)
SHARP	20AM100	N/A	CO-CHANNEL INTERFERENCE	CHECK/REPLACE ANTENNA BLOCK (RUNTK0371CEZZ)
SHARP	20AM100	N/A	NO START-UP BUT RELAY DOES CLICK	CHECK/REPLACE R752 FOR CHANGE IN VALUE (10k )
SHARP	20AM120	N/A	NO START-UP BUT RELAY DOES CLICK	CHECK/REPLACE R752 FOR CHANGE IN VALUE (10k )
SHARP	20AM120	N/A	CO-CHANNEL INTERFERENCE	CHECK/REPLACE ANTENNA BLOCK (RUNTK0371CEZZ)
SHARP	20AM120	N/A	CO-CHANNEL INTERFERENCE	REPLACE ANTENNA BLOCK (P/N # RUNTK0371CEZZ)
SHARP	20AM120	N/A	VENETIAN BLIND EFFECT - HORZ. BARS ACROSS SCREEN	CHECK/REPLACE IC4201 (P/N# RH-IX1705CEZZ)
SHARP	20AM200	N/A	VENETIAN BLIND EFFECT - HORZ. BARS ACROSS SCREEN	CHECK/REPLACE IC4201 (P/N# RH-IX1705CEZZ)
SHARP	20AM200	N/A	NO START-UP BUT RELAY DOES CLICK	CHECK/REPLACE R752 FOR CHANGE IN VALUE (10k )
SHARP	20AM300	N/A	VENETIAN BLIND EFFECT - HORZ. BARS ACROSS SCREEN	CHECK/REPLACE IC4201 (P/N# RH-IX1705CEZZ)
SHARP	20AM300	N/A	CO-CHANNEL INTERFERENCE	CHECK/REPLACE ANTENNA BLOCK (RUNTK0371CEZZ)
SHARP	20AM300	N/A	NO START-UP BUT RELAY DOES CLICK	CHECK/REPLACE R752 FOR CHANGE IN VALUE (10k )
SHARP	20AM300	N/A	CO-CHANNEL INTERFERENCE	REPLACE ANTENNA BLOCK (P/N # RUNTK0371CEZZ)
SHARP	20AS100	N/A	NO START-UP BUT RELAY DOES CLICK	CHECK/REPLACE R752 FOR CHANGE IN VALUE (10k )
SHARP	20AS100	N/A	CO-CHANNEL INTERFERENCE	CHECK/REPLACE ANTENNA BLOCK (RUNTK0371CEZZ)
SHARP	20AS100	N/A	CO-CHANNEL INTERFERENCE	REPLACE ANTENNA BLOCK (P/N # RUNTK0371CEZZ)
SHARP	20AS100	N/A	VENETIAN BLIND EFFECT - HORZ. BARS ACROSS SCREEN	CHECK/REPLACE IC4201 (P/N# RH-IX1705CEZZ)
SHARP	20AS120	N/A	CO-CHANNEL INTERFERENCE	CHECK/REPLACE ANTENNA BLOCK (RUNTK0371CEZZ)
SHARP	20AS120	N/A	NO START-UP BUT RELAY DOES CLICK	CHECK/REPLACE R752 FOR CHANGE IN VALUE (10k )
SHARP	20AS120	N/A	CO-CHANNEL INTERFERENCE	REPLACE ANTENNA BLOCK (P/N # RUNTK0371CEZZ)
SHARP	20AS120	N/A	VENETIAN BLIND EFFECT - HORZ. BARS ACROSS SCREEN	CHECK/REPLACE IC4201 (P/N# RH-IX1705CEZZ)
SHARP	20AS200	N/A	VENETIAN BLIND EFFECT - HORZ. BARS ACROSS SCREEN	CHECK/REPLACE IC4201 (P/N# RH-IX1705CEZZ)
SHARP	20AS200	N/A	CO-CHANNEL INTERFERENCE	REPLACE ANTENNA BLOCK (P/N # RUNTK0371CEZZ)
SHARP	20AS200	N/A	CO-CHANNEL INTERFERENCE	CHECK/REPLACE ANTENNA BLOCK (RUNTK0371CEZZ)
SHARP	20AS200	N/A	NO START-UP BUT RELAY DOES CLICK	CHECK/REPLACE R752 FOR CHANGE IN VALUE (10k )
SHARP	20AS300	N/A	VENETIAN BLIND EFFECT - HORZ. BARS ACROSS SCREEN	CHECK/REPLACE IC4201 (P/N# RH-IX1705CEZZ)
SHARP	20AS300	N/A	CO-CHANNEL INTERFERENCE	REPLACE ANTENNA BLOCK (P/N # RUNTK0371CEZZ)
SHARP	20AS300	N/A	NO START-UP BUT RELAY DOES CLICK	CHECK/REPLACE R752 FOR CHANGE IN VALUE (10k )
SHARP	20AS300	N/A	CO-CHANNEL INTERFERENCE	CHECK/REPLACE ANTENNA BLOCK (RUNTK0371CEZZ)
SHARP	20CM100	N/A	CO-CHANNEL INTERFERENCE	REPLACE ANTENNA BLOCK (P/N # RUNTK0371CEZZ)
SHARP	20CM120	N/A	CO-CHANNEL INTERFERENCE	REPLACE ANTENNA BLOCK (P/N # RUNTK0371CEZZ)
SHARP	20CM150	N/A	CO-CHANNEL INTERFERENCE	REPLACE ANTENNA BLOCK (P/N # RUNTK0371CEZZ)
SHARP	20CS200	N/A	CO-CHANNEL INTERFERENCE	REPLACE ANTENNA BLOCK (P/N # RUNTK0371CEZZ)
SHARP	20EM100	N/A	HAS OSD BUT NO SOUND	CHECK/REPLACE D763 (1N4148 OR RH-DX0045GEZZ)
SHARP	20EM100	N/A	ON SCREEN CUSTOMER ADJUSTMENTS HAVE 3 LEVELS-O%,50%,100% THERE IS NO IN BETWEEN VALUES	CHECK/REPLACE IC2701 (P/N# RH-IX2281CEZZ)
SHARP	20EM120	N/A	ON SCREEN CUSTOMER ADJUSTMENTS HAVE 3 LEVELS-O%,50%,100% THERE IS NO IN BETWEEN VALUES	CHECK/REPLACE IC2701 (P/N# RH-IX2281CEZZ)
SHARP	20EM120	N/A	HAS OSD BUT NO SOUND	CHECK/REPLACE D763 (1N4148 OR RH-DX0045GEZZ)
SHARP	20EM150	N/A	HAS OSD BUT NO SOUND	CHECK/REPLACE D763 (1N4148 OR RH-DX0045GEZZ)
SHARP	20EM40	N/A	HAS OSD BUT NO SOUND	CHECK/REPLACE D763 (1N4148 OR RH-DX0045GEZZ)
SHARP	20EM50	N/A	HAS OSD BUT NO SOUND	CHECK/REPLACE D763 (1N4148 OR RH-DX0045GEZZ)
SHARP	20EM50	N/A	ON SCREEN CUSTOMER ADJUSTMENTS HAVE 3 LEVELS-O%,50%,100% THERE IS NO IN BETWEEN VALUES	CHECK/REPLACE IC2701 (P/N# RH-IX2281CEZZ)
SHARP	20ES110	N/A	ON SCREEN CUSTOMER ADJUSTMENTS HAVE 3 LEVELS-O%,50%,100% THERE IS NO IN BETWEEN VALUES	CHECK/REPLACE IC2701 (P/N# RH-IX2281CEZZ)
SHARP	20ES130	N/A	ON SCREEN CUSTOMER ADJUSTMENTS HAVE 3 LEVELS-O%,50%,100% THERE IS NO IN BETWEEN VALUES	CHECK/REPLACE IC2701 (P/N# RH-IX2281CEZZ)
SHARP	20ES200	N/A	ON SCREEN CUSTOMER ADJUSTMENTS HAVE 3 LEVELS-O%,50%,100% THERE IS NO IN BETWEEN VALUES	CHECK/REPLACE IC2701 (P/N# RH-IX2281CEZZ)
SHARP	20ES40	N/A	ON SCREEN CUSTOMER ADJUSTMENTS HAVE 3 LEVELS-O%,50%,100% THERE IS NO IN BETWEEN VALUES	CHECK/REPLACE IC2701 (P/N# RH-IX2281CEZZ)
SHARP	20ES50	N/A	ON SCREEN CUSTOMER ADJUSTMENTS HAVE 3 LEVELS-O%,50%,100% THERE IS NO IN BETWEEN VALUES	CHECK/REPLACE IC2701 (P/N# RH-IX2281CEZZ)
SHARP	20FM100	N/A	SET SHUTS DOWN WHEN TURNED ON	CHECK/REPLACE C710 FOR OPEN
SHARP	20FM100	N/A	DEAD SET - NO RELAY CLICK - 5v SUPPLY DOWN TO 1 VOLT OR LESS	CHECK/REPLACE REMOTE RECEIVER (P/N# RRMCU0207CEZZ)
SHARP	20FM120	N/A	SET SHUTS DOWN WHEN TURNED ON	CHECK/REPLACE C710 FOR OPEN
SHARP	20FM150	N/A	DEAD SET - NO RELAY CLICK - 5v SUPPLY DOWN TO 1 VOLT OR LESS	CHECK/REPLACE REMOTE RECEIVER (P/N# RRMCU0207CEZZ)
SHARP	20FM150	N/A	SET SHUTS DOWN WHEN TURNED ON	CHECK/REPLACE C710 FOR OPEN
SHARP	20FM40	N/A	DEAD SET - NO RELAY CLICK - 5v SUPPLY DOWN TO 1 VOLT OR LESS	CHECK/REPLACE REMOTE RECEIVER (P/N# RRMCU0207CEZZ)
SHARP	20FM40	N/A	SET SHUTS DOWN WHEN TURNED ON	CHECK/REPLACE C710 FOR OPEN
SHARP	20FM50	N/A	SET SHUTS DOWN WHEN TURNED ON	CHECK/REPLACE C710 FOR OPEN
SHARP	20FM50	N/A	DEAD SET - NO RELAY CLICK - 5v SUPPLY DOWN TO 1 VOLT OR LESS	CHECK/REPLACE REMOTE RECEIVER (P/N# RRMCU0207CEZZ)
SHARP	20FS100	N/A	SHORT VERTICAL SWEEP AT BOTTOM AND STRETCHED VERTICAL AT THE TOP	CHECK TO MAKE SURE THAT S501 SWITCH IS IN THE DETENT POSITION AND NOT HALF WAY BETWEEN POSITIONS
SHARP	20FS120	N/A	SHORT VERTICAL SWEEP AT BOTTOM AND STRETCHED VERTICAL AT THE TOP	CHECK TO MAKE SURE THAT S501 SWITCH IS IN THE DETENT POSITION AND NOT HALF WAY BETWEEN POSITIONS
SHARP	20FS150	N/A	SHORT VERTICAL SWEEP AT BOTTOM AND STRETCHED VERTICAL AT THE TOP	CHECK TO MAKE SURE THAT S501 SWITCH IS IN THE DETENT POSITION AND NOT HALF WAY BETWEEN POSITIONS
SHARP	20FS200	N/A	SHORT VERTICAL SWEEP AT BOTTOM AND STRETCHED VERTICAL AT THE TOP	CHECK TO MAKE SURE THAT S501 SWITCH IS IN THE DETENT POSITION AND NOT HALF WAY BETWEEN POSITIONS
SHARP	20FS300	N/A	SHORT VERTICAL SWEEP AT BOTTOM AND STRETCHED VERTICAL AT THE TOP	CHECK TO MAKE SURE THAT S501 SWITCH IS IN THE DETENT POSITION AND NOT HALF WAY BETWEEN POSITIONS
SHARP	20FS3900	N/A	SHORT VERTICAL SWEEP AT BOTTOM AND STRETCHED VERTICAL AT THE TOP	CHECK TO MAKE SURE THAT S501 SWITCH IS IN THE DETENT POSITION AND NOT HALF WAY BETWEEN POSITIONS
SHARP	20FS40	N/A	SHORT VERTICAL SWEEP AT BOTTOM AND STRETCHED VERTICAL AT THE TOP	CHECK TO MAKE SURE THAT S501 SWITCH IS IN THE DETENT POSITION AND NOT HALF WAY BETWEEN POSITIONS
SHARP	20FS50	N/A	SHORT VERTICAL SWEEP AT BOTTOM AND STRETCHED VERTICAL AT THE TOP	CHECK TO MAKE SURE THAT S501 SWITCH IS IN THE DETENT POSITION AND NOT HALF WAY BETWEEN POSITIONS
SHARP	20GM100	N/A	DEAD - JUST CLICKS	CHECK/REPLACE Q602 (VS2SD1554//1E) AND R717 (VRW-KQ4AC6R8K)
SHARP	20GM100	N/A	RED 'T' IN THE UPPER RIGHT CORNER OF SCREEN CAUSE BY PRESSING '4' OF ANOTHER MANUFACTURES REMOTE	BEFORE REPL.IC2001, PRESS '4' KEY ON ORIG. REMOTE TO RESET CHECK/REPLACE IC2001 (P/N# RH-IX2552CEN2 OR RH-IX2599CEN2)
SHARP	20GM100	N/A	DARK VERTICAL LINE ON THE RIGHT SIDE OF SCREEN WHEN USING THE FRONT A-V JACKS FOR AN INPUT	REMOVE JUMPER J16 (NEAR B+ ADJUST), CUT THE GROUND WIRE PIN# 3 OF J14 (NEAR IC201) AND TAPE END
SHARP	20GM100	N/A	SHORT VERTICAL SWEEP	CHECK/REPLACE C513 (470uF @ 50v)
SHARP	20GM120	N/A	DARK VERTICAL LINE ON THE RIGHT SIDE OF SCREEN WHEN USING THE FRONT A-V JACKS FOR AN INPUT	REMOVE JUMPER J16 (NEAR B+ ADJUST), CUT THE GROUND WIRE PIN# 3 OF J14 (NEAR IC201) AND TAPE END
SHARP	20GM120	N/A	SHORT VERTICAL SWEEP	CHECK/REPLACE C513 (470uF @ 50v)
SHARP	20GM120	N/A	DEAD - JUST CLICKS	CHECK/REPLACE Q602 (VS2SD1554//1E) AND R717 (VRW-KQ4AC6R8K)
SHARP	20GM120	N/A	RED 'T' IN THE UPPER RIGHT CORNER OF SCREEN CAUSE BY PRESSING '4' OF ANOTHER MANUFACTURES REMOTE	BEFORE REPL.IC2001, PRESS '4' KEY ON ORIG. REMOTE TO RESET CHECK/REPLACE IC2001 (P/N# RH-IX2552CEN2 OR RH-IX2599CEN2)
SHARP	20GM150	N/A	SHORT VERTICAL SWEEP	CHECK/REPLACE C513 (470uF @ 50v)
SHARP	20GM150	N/A	DEAD - JUST CLICKS	CHECK/REPLACE Q602 (VS2SD1554//1E) AND R717 (VRW-KQ4AC6R8K)
SHARP	20GM200	N/A	SHORT VERTICAL SWEEP	CHECK/REPLACE C513 (470uF @ 50v)
SHARP	20GM200	N/A	DEAD - JUST CLICKS	CHECK/REPLACE Q602 (VS2SD1554//1E) AND R717 (VRW-KQ4AC6R8K)
SHARP	20GM60	N/A	SHORT VERTICAL SWEEP	CHECK/REPLACE C513 (470uF @ 50v)
SHARP	20GM60	N/A	DEAD - JUST CLICKS	CHECK/REPLACE Q602 (VS2SD1554//1E) AND R717 (VRW-KQ4AC6R8K)
SHARP	20GM80	N/A	SHORT VERTICAL SWEEP	CHECK/REPLACE C513 (470uF @ 50v)
SHARP	20GM80	N/A	DEAD - JUST CLICKS	CHECK/REPLACE Q602 (VS2SD1554//1E) AND R717 (VRW-KQ4AC6R8K)
SHARP	20GS100	N/A	DEAD SET - RELAY DOES CLICK	CHECK/REPLACE R719 (P/N# VRW-KQ3HC5R6K) 5.6 @ 5watt AND Q602 (P/N# VS2SD2095//1E) 2SD2095
SHARP	20GS100	N/A	RED 'T' IN THE UPPER RIGHT CORNER OF SCREEN CAUSE BY PRESSING '4' OF ANOTHER MANUFACTURES REMOTE	BEFORE REPL.IC2001, PRESS '4' KEY ON ORIG. REMOTE TO RESET CHECK/REPLACE IC2001 (P/N# RH-IX2552CEN2 OR RH-IX2599CEN2)
SHARP	20GS100	N/A	NO SOUND BUT PICTURE IS OK - SET MAY EXHIBIT AFT PROBLEMS	GO INTO SERVICE MENU BY SHORTING TP2001 & TP2002, USE CHAN. UP TO ADVANCE TO S33, USE VOL UP/DOWN TO SET TO 'B7'
SHARP	20GS100	N/A	INTERMITTENTLY SHUTS OFF	CHECK/RESOLDER CONNECTIONS ON PIN #9 & #10 OF FLYBACK
SHARP	20GS100	N/A	NO SOUND - PICTURE IS FINE	SHORT TP2001 AND TP2002 - ADVANCE ON-SCREEN REGISTER TO #33, - ADJUST SETTING TO #02 INSTEAD OF #00
SHARP	20GS120	N/A	NO SOUND BUT PICTURE IS OK - SET MAY EXHIBIT AFT PROBLEMS	GO INTO SERVICE MENU BY SHORTING TP2001 & TP2002, USE CHAN. UP TO ADVANCE TO S33, USE VOL UP/DOWN TO SET TO 'B7'
SHARP	20GS120	N/A	RED 'T' IN THE UPPER RIGHT CORNER OF SCREEN CAUSE BY PRESSING '4' OF ANOTHER MANUFACTURES REMOTE	BEFORE REPL.IC2001, PRESS '4' KEY ON ORIG. REMOTE TO RESET CHECK/REPLACE IC2001 (P/N# RH-IX2552CEN2 OR RH-IX2599CEN2)
SHARP	20GS120	N/A	INTERMITTENTLY SHUTS OFF	CHECK/RESOLDER CONNECTIONS ON PIN #9 & #10 OF FLYBACK
SHARP	20GS120	N/A	DEAD SET - RELAY DOES CLICK	CHECK/REPLACE R719 (P/N# VRW-KQ3HC5R6K) 5.6 @ 5watt AND Q602 (P/N# VS2SD2095//1E) 2SD2095
SHARP	20GS120	N/A	NO SOUND - PICTURE IS FINE	SHORT TP2001 AND TP2002 - ADVANCE ON-SCREEN REGISTER TO #33, - ADJUST SETTING TO #02 INSTEAD OF #00
SHARP	20GS60	N/A	DEAD SET - RELAY DOES CLICK	CHECK/REPLACE R719 (P/N# VRW-KQ3HC5R6K) 5.6 @ 5watt AND Q602 (P/N# VS2SD2095//1E) 2SD2095
SHARP	20GS60	N/A	INTERMITTENTLY SHUTS OFF	CHECK/RESOLDER CONNECTIONS ON PIN #9 & #10 OF FLYBACK
SHARP	20GS60	N/A	NO SOUND - PICTURE IS FINE	SHORT TP2001 AND TP2002 - ADVANCE ON-SCREEN REGISTER TO #33, - ADJUST SETTING TO #02 INSTEAD OF #00
SHARP	20GS80	N/A	NO SOUND - PICTURE IS FINE	SHORT TP2001 AND TP2002 - ADVANCE ON-SCREEN REGISTER TO #33, - ADJUST SETTING TO #02 INSTEAD OF #00
SHARP	20GS80	N/A	NO SOUND BUT PICTURE IS OK - SET MAY EXHIBIT AFT PROBLEMS	GO INTO SERVICE MENU BY SHORTING TP2001 & TP2002, USE CHAN. UP TO ADVANCE TO S33, USE VOL UP/DOWN TO SET TO '96'
SHARP	20GS80	N/A	RED 'T' IN THE UPPER RIGHT CORNER OF SCREEN CAUSE BY PRESSING '4' OF ANOTHER MANUFACTURES REMOTE	BEFORE REPL.IC2001, PRESS '4' KEY ON ORIG. REMOTE TO RESET CHECK/REPLACE IC2001 (P/N# RH-IX2552CEN2 OR RH-IX2599CEN2)
SHARP	20GS80	N/A	DEAD SET - RELAY DOES CLICK	CHECK/REPLACE R719 (P/N# VRW-KQ3HC5R6K) 5.6 @ 5watt AND Q602 (P/N# VS2SD2095//1E) 2SD2095
SHARP	20GS80	N/A	INTERMITTENTLY SHUTS OFF	CHECK/RESOLDER CONNECTIONS ON PIN #9 & #10 OF FLYBACK
SHARP	20HM100	N/A	DARK VERTICAL LINE ON THE RIGHT SIDE OF SCREEN WHEN USING THE FRONT A-V JACKS FOR AN INPUT	REMOVE JUMPER J16 (NEAR B+ ADJUST), CUT THE GROUND WIRE PIN# 3 OF J14 (NEAR IC201) AND TAPE END
SHARP	20JM100	N/A	INTERMITTENT TUNER OPERATION - GOES TO SNOW	CHECK/REPLACE C52 (22uF @ 16v TANTALUM)
SHARP	20JS100	N/A	INTERMITTENT TUNER OPERATION - GOES TO SNOW	CHECK/REPLACE C52 (22uF @ 16v TANTALUM)
SHARP	20KP75	N/A	BUZZING SOUND ON CERTAIN CABLE CHANNELS	PLACE A 330pF CAPACITOR (VCKZPA1HB331K) BETWEEN PIN # 41 OF IC801 AND JUNCTIONS OF CF301 AND R354.
SHARP	20KP95	N/A	BUZZING SOUND ON CERTAIN CABLE CHANNELS	PLACE A 330pF CAPACITOR (VCKZPA1HB331K) BETWEEN PIN # 41 OF IC801 AND JUNCTIONS OF CF301 AND R354.
SHARP	20LP76	N/A	INTERMITTENTLY TICKS OR DEAD - NO START-UP	CHECK/RESOLDER CONNECTIONS ON Q601,Q602 AND T601
SHARP	20LP76	N/A	BUZZING SOUND ON CERTAIN CABLE CHANNELS	PLACE A 330pF CAPACITOR (VCKZPA1HB331K) BETWEEN PIN # 41 OF IC801 AND JUNCTIONS OF CF301 AND R354.
SHARP	20LP86	N/A	BUZZING SOUND ON CERTAIN CABLE CHANNELS	PLACE A 330pF CAPACITOR (VCKZPA1HB331K) BETWEEN PIN # 41 OF IC801 AND JUNCTIONS OF CF301 AND R354.
SHARP	20MP67	N/A	BUZZING SOUND ON CERTAIN CABLE CHANNELS	PLACE A 330pF CAPACITOR (VCKZPA1HB331K) BETWEEN PIN # 41 OF IC801 AND JUNCTIONS OF CF301 AND R354.
SHARP	20NL10	N/A	POWER RELAY FAILURE	INSTALL KIT # BQC-20RV99/-1
SHARP	20NL20	N/A	POWER RELAY FAILURE	INSTALL KIT # BQC-20RV99/-1
SHARP	20NL30	N/A	CO-CHANNEL INTERFERENCE	REPLACE ANTENNA BLOCK (P/N # RUNTK0371CEZZ)
SHARP	20NL30	N/A	CO-CHANNEL INTERFERENCE	CHECK/REPLACE ANTENNA BLOCK (RUNTK0371CEZZ)
SHARP	20NL68	N/A	CO-CHANNEL INTERFERENCE	REPLACE ANTENNA BLOCK (P/N # RUNTK0371CEZZ)
SHARP	20NL78	N/A	CO-CHANNEL INTERFERENCE	REPLACE ANTENNA BLOCK (P/N # RUNTK0371CEZZ)
SHARP	20NV68	N/A	CO-CHANNEL INTERFERENCE	CHECK/REPLACE ANTENNA BLOCK (RUNTK0371CEZZ)
SHARP	20NV68	N/A	NO COLOR	CHECK/REPLACE C809 TRIMMER (RTO-S1002AEZZ)
SHARP	20NV78	N/A	CO-CHANNEL INTERFERENCE	CHECK/REPLACE ANTENNA BLOCK (RUNTK0371CEZZ)
SHARP	20RV169	N/A	DEAD SET	CHECK D701-D704,R701
SHARP	20RV169	N/A	FLYBACK SQUEALS AND SET HAS AN HOUR GLASS SHAPED PIX	CHECK/REPLACE IC701
SHARP	20RV169	N/A	REGULATOR WON'T START UP	CHECK D705,R702,IC701
SHARP	20RV619	N/A	ONLY SNOW ON SCREEN-WILL NOT TUNE A CHANNEL	CHECK IC1401 (UPC1486C)
SHARP	20RV619	N/A	CO-CHANNEL INTERFERENCE	CHECK/REPLACE ANTENNA BLOCK (RUNTK0371CEZZ)
SHARP	20RV619	N/A	DEAD SET	CHECK D701-D704,R701
SHARP	20RV619	N/A	FLYBACK SQUEALS AND SET HAS AN HOUR GLASS SHAPED PIX	CHECK/REPLACE IC701
SHARP	20RV619	N/A	CO-CHANNEL INTERFERENCE	REPLACE ANTENNA BLOCK (P/N # RUNTK0371CEZZ)
SHARP	20RV619	N/A	DISTORTED AUDIO-MAYBE AFTER SET IS ON FOR 5-10 MINUTES.	REPLACE IC201 (TA8680N)
SHARP	20RV619	N/A	REGULATOR WON'T START UP	CHECK D705,R702,IC701
SHARP	20RV629	N/A	ONLY SNOW ON SCREEN-WILL NOT TUNE A CHANNEL	CHECK IC1401 (UPC1486C)
SHARP	20RV629	N/A	REGULATOR WON'T START UP	CHECK D705,R702,IC701
SHARP	20RV629	N/A	DEAD SET	CHECK D701-D704,R701
SHARP	20RV629	N/A	CO-CHANNEL INTERFERENCE	REPLACE ANTENNA BLOCK (P/N # RUNTK0371CEZZ)
SHARP	20RV629	N/A	CO-CHANNEL INTERFERENCE	CHECK/REPLACE ANTENNA BLOCK (RUNTK0371CEZZ)
SHARP	20RV629	N/A	FLYBACK SQUEALS AND SET HAS AN HOUR GLASS SHAPED PIX	CHECK/REPLACE IC701
SHARP	20RV629	N/A	DISTORTED AUDIO-MAYBE AFTER SET IS ON FOR 5-10 MINUTES.	REPLACE IC201 (TA8680N)
SHARP	20RV649	N/A	FLYBACK SQUEALS AND SET HAS AN HOUR GLASS SHAPED PIX	CHECK/REPLACE IC701
SHARP	20RV649	N/A	CO-CHANNEL INTERFERENCE	CHECK/REPLACE ANTENNA BLOCK (RUNTK0371CEZZ)
SHARP	20RV649	N/A	REGULATOR WON'T START UP	CHECK D705,R702,IC701
SHARP	20RV649	N/A	ONLY SNOW ON SCREEN-WILL NOT TUNE A CHANNEL	CHECK IC1401 (UPC1486C)
SHARP	20RV649	N/A	DEAD SET	CHECK D701-D704,R701
SHARP	20RV649	N/A	DISTORTED AUDIO-MAYBE AFTER SET IS ON FOR 5-10 MINUTES.	REPLACE IC201 (TA8680N)
SHARP	20RV649	N/A	CO-CHANNEL INTERFERENCE	REPLACE ANTENNA BLOCK (P/N # RUNTK0371CEZZ)
SHARP	20RV69	N/A	CO-CHANNEL INTERFERENCE	CHECK/REPLACE ANTENNA BLOCK (RUNTK0371CEZZ)
SHARP	20RV69	N/A	REGULATOR WON'T START UP	CHECK D705,R702,IC701
SHARP	20RV69	N/A	DISTORTED AUDIO-MAYBE AFTER SET IS ON FOR 5-10 MINUTES.	REPLACE IC201 (TA8680N)
SHARP	20RV69	N/A	ONLY SNOW ON SCREEN-WILL NOT TUNE A CHANNEL	CHECK IC1401 (UPC1486C)
SHARP	20RV69	N/A	FLYBACK SQUEALS AND SET HAS AN HOUR GLASS SHAPED PIX	CHECK/REPLACE IC701
SHARP	20RV69	N/A	DEAD SET	CHECK D701-D704,R701
SHARP	20RV719	N/A	DISTORTED SOUND AND USUALLY THERMAL	CHECK/REPLACE IC201 (TA8680N)
SHARP	20RV719	N/A	FLYBACK SQUEALS AND SET HAS AN HOUR GLASS SHAPED PIX	CHECK/REPLACE IC701
SHARP	20RV719	N/A	CO-CHANNEL INTERFERENCE	REPLACE ANTENNA BLOCK (P/N # RUNTK0371CEZZ)
SHARP	20RV719	N/A	CO-CHANNEL INTERFERENCE	CHECK/REPLACE ANTENNA BLOCK (RUNTK0371CEZZ)
SHARP	20RV729	N/A	DISTORTED SOUND AND USUALLY THERMAL	CHECK/REPLACE IC201 (TA8680N)
SHARP	20RV729	N/A	CO-CHANNEL INTERFERENCE	CHECK/REPLACE ANTENNA BLOCK (RUNTK0371CEZZ)
SHARP	20RV729	N/A	FLYBACK SQUEALS AND SET HAS AN HOUR GLASS SHAPED PIX	CHECK/REPLACE IC701
SHARP	20RV729	N/A	CO-CHANNEL INTERFERENCE	REPLACE ANTENNA BLOCK (P/N # RUNTK0371CEZZ)
SHARP	20RV749	N/A	FLYBACK SQUEALS AND SET HAS AN HOUR GLASS SHAPED PIX	CHECK/REPLACE IC701
SHARP	20RV749	N/A	DISTORTED SOUND AND USUALLY THERMAL	CHECK/REPLACE IC201 (TA8680N)
SHARP	20RV749	N/A	CO-CHANNEL INTERFERENCE	REPLACE ANTENNA BLOCK (P/N # RUNTK0371CEZZ)
SHARP	20RV749	N/A	CO-CHANNEL INTERFERENCE	CHECK/REPLACE ANTENNA BLOCK (RUNTK0371CEZZ)
SHARP	20RV79	N/A	DISTORTED SOUND AND USUALLY THERMAL	CHECK/REPLACE IC201 (TA8680N)
SHARP	20RV79	N/A	CO-CHANNEL INTERFERENCE	CHECK/REPLACE ANTENNA BLOCK (RUNTK0371CEZZ)
SHARP	20RV79	N/A	FLYBACK SQUEALS AND SET HAS AN HOUR GLASS SHAPED PIX	CHECK/REPLACE IC701
SHARP	20RV79	N/A	CO-CHANNEL INTERFERENCE	REPLACE ANTENNA BLOCK (P/N # RUNTK0371CEZZ)
SHARP	20RV99	N/A	POWER RELAY FAILURE	INSTALL KIT # BQC-20RV99/-1
SHARP	20SB55	N/A	CO-CHANNEL INTERFERENCE	CHECK/REPLACE ANTENNA BLOCK (RUNTK0371CEZZ)
SHARP	20SB55	N/A	CO-CHANNEL INTERFERENCE	REPLACE ANTENNA BLOCK (P/N # RUNTK0371CEZZ)
SHARP	20SB55	N/A	FLYBACK SQUEALS AND SET HAS AN HOUR GLASS SHAPED PIX	CHECK/REPLACE IC701
SHARP	20SB65	N/A	CO-CHANNEL INTERFERENCE	REPLACE ANTENNA BLOCK (P/N # RUNTK0371CEZZ)
SHARP	20SB65	N/A	CO-CHANNEL INTERFERENCE	CHECK/REPLACE ANTENNA BLOCK (RUNTK0371CEZZ)
SHARP	20SV60	N/A	CO-CHANNEL INTERFERENCE	REPLACE ANTENNA BLOCK (P/N # RUNTK0371CEZZ)
SHARP	20SV60	N/A	CO-CHANNEL INTERFERENCE	CHECK/REPLACE ANTENNA BLOCK (RUNTK0371CEZZ)
SHARP	20SV610	N/A	CO-CHANNEL INTERFERENCE	REPLACE ANTENNA BLOCK (P/N # RUNTK0371CEZZ)
SHARP	20SV610	N/A	CO-CHANNEL INTERFERENCE	CHECK/REPLACE ANTENNA BLOCK (RUNTK0371CEZZ)
SHARP	20SV620	N/A	CO-CHANNEL INTERFERENCE	REPLACE ANTENNA BLOCK (P/N # RUNTK0371CEZZ)
SHARP	20SV620	N/A	CO-CHANNEL INTERFERENCE	CHECK/REPLACE ANTENNA BLOCK (RUNTK0371CEZZ)
SHARP	20SV640	N/A	CO-CHANNEL INTERFERENCE	REPLACE ANTENNA BLOCK (P/N # RUNTK0371CEZZ)
SHARP	20SV640	N/A	CO-CHANNEL INTERFERENCE	CHECK/REPLACE ANTENNA BLOCK (RUNTK0371CEZZ)
SHARP	20SV70	N/A	SEVERAL KEYBOARD FUNCTIONS DON'T WORK	CHECK/REPLACE D1020,D1019,D1018,D1017,D1045,D1044,D1043 AND D1042
SHARP	20SV70	N/A	CO-CHANNEL INTERFERENCE	CHECK/REPLACE ANTENNA BLOCK (RUNTK0371CEZZ)
SHARP	20SV70	N/A	CO-CHANNEL INTERFERENCE	REPLACE ANTENNA BLOCK (P/N # RUNTK0371CEZZ)
SHARP	20SV710	N/A	CO-CHANNEL INTERFERENCE	REPLACE ANTENNA BLOCK (P/N # RUNTK0371CEZZ)
SHARP	20SV710	N/A	CO-CHANNEL INTERFERENCE	CHECK/REPLACE ANTENNA BLOCK (RUNTK0371CEZZ)
SHARP	20SV710	N/A	SEVERAL KEYBOARD FUNCTIONS DON'T WORK	CHECK/REPLACE D1020,D1019,D1018,D1017,D1045,D1044,D1043 AND D1042
SHARP	20SV720	N/A	CO-CHANNEL INTERFERENCE	REPLACE ANTENNA BLOCK (P/N # RUNTK0371CEZZ)
SHARP	20SV720	N/A	CO-CHANNEL INTERFERENCE	CHECK/REPLACE ANTENNA BLOCK (RUNTK0371CEZZ)
SHARP	20SV720	N/A	SEVERAL KEYBOARD FUNCTIONS DON'T WORK	CHECK/REPLACE D1020,D1019,D1018,D1017,D1045,D1044,D1043 AND D1042
SHARP	20SV740	N/A	SEVERAL KEYBOARD FUNCTIONS DON'T WORK	CHECK/REPLACE D1020,D1019,D1018,D1017,D1045,D1044,D1043 AND D1042
SHARP	20SV740	N/A	CO-CHANNEL INTERFERENCE	CHECK/REPLACE ANTENNA BLOCK (RUNTK0371CEZZ)
SHARP	20SV740	N/A	CO-CHANNEL INTERFERENCE	REPLACE ANTENNA BLOCK (P/N # RUNTK0371CEZZ)
SHARP	25AM050	N/A	VENETIAN BLIND EFFECT - HORZ. BARS ACROSS SCREEN	CHECK/REPLACE IC4201 (P/N# RH-IX1705CEZZ)
SHARP	25AM050	N/A	NO START-UP BUT RELAY DOES CLICK	CHECK/REPLACE R752 FOR CHANGE IN VALUE (10k )
SHARP	25AM050	N/A	POWER RELAY FAILURE	INSTALL KIT # BQC-25AM100-1
SHARP	25AM050	N/A	AUDIO DISTORTION OR BUZZ IN AUDIO ON SCENES WITH WHITE SUBTITLES	ADD A 0.1uF IN PARALLEL WITH C4304 (P/N VCFYHA1HA104J)
SHARP	25AM100	N/A	POWER RELAY FAILURE	INSTALL KIT # BQC-25AM100-1
SHARP	25AM100	N/A	NO START-UP BUT RELAY DOES CLICK	CHECK/REPLACE R752 FOR CHANGE IN VALUE (10k )
SHARP	25AM100	N/A	AUDIO DISTORTION OR BUZZ IN AUDIO ON SCENES WITH WHITE SUBTITLES	ADD A 0.1uF IN PARALLEL WITH C4304 (P/N VCFYHA1HA104J)
SHARP	25AM100	N/A	VENETIAN BLIND EFFECT - HORZ. BARS ACROSS SCREEN	CHECK/REPLACE IC4201 (P/N# RH-IX1705CEZZ)
SHARP	25AM120	N/A	VENETIAN BLIND EFFECT - HORZ. BARS ACROSS SCREEN	CHECK/REPLACE IC4201 (P/N# RH-IX1705CEZZ)
SHARP	25AM120	N/A	NO START-UP BUT RELAY DOES CLICK	CHECK/REPLACE R752 FOR CHANGE IN VALUE (10k )
SHARP	25AM120	N/A	AUDIO DISTORTION OR BUZZ IN AUDIO ON SCENES WITH WHITE SUBTITLES	ADD A 0.1uF IN PARALLEL WITH C4304 (P/N VCFYHA1HA104J)
SHARP	25AM120	N/A	POWER RELAY FAILURE	INSTALL KIT # BQC-25AM100-1
SHARP	25AM200	N/A	VENETIAN BLIND EFFECT - HORZ. BARS ACROSS SCREEN	CHECK/REPLACE IC4201 (P/N# RH-IX1705CEZZ)
SHARP	25AM200	N/A	NO START-UP BUT RELAY DOES CLICK	CHECK/REPLACE R752 FOR CHANGE IN VALUE (10k )
SHARP	25AM300	N/A	NO START-UP BUT RELAY DOES CLICK	CHECK/REPLACE R752 FOR CHANGE IN VALUE (10k )
SHARP	25AM300	N/A	VENETIAN BLIND EFFECT - HORZ. BARS ACROSS SCREEN	CHECK/REPLACE IC4201 (P/N# RH-IX1705CEZZ)
SHARP	25AS100	N/A	NO START-UP BUT RELAY DOES CLICK	CHECK/REPLACE R752 FOR CHANGE IN VALUE (10k )
SHARP	25AS100	N/A	INTERMITTENT VIDEO	CHECK/RESOLDER CONNECTIONS ON DL2701
SHARP	25AS100	N/A	VENETIAN BLIND EFFECT - HORZ. BARS ACROSS SCREEN	CHECK/REPLACE IC4201 (P/N# RH-IX1705CEZZ)
SHARP	25AS100	N/A	NO TUNING AND NO OSD	CHECK/REPLACE IC1401 (UPC1486C)
SHARP	25AS100	N/A	STEREO INDICATOR BLINKS ON CERTAIN CABLE SYSTEMS - SOUND ALTERNATES BETWEEN STEREO AND MONO	ADD 680pF (P/N# VCKYPA2HB681K) FROM IC4201 PIN #1 TO GROUND
SHARP	25AS100	N/A	POWER RELAY FAILURE	INSTALL KIT # BQC-25AM100-1
SHARP	25AS120	N/A	STEREO INDICATOR BLINKS ON CERTAIN CABLE SYSTEMS - SOUND ALTERNATES BETWEEN STEREO AND MONO	ADD 680pF (P/N# VCKYPA2HB681K) FROM IC4201 PIN #1 TO GROUND
SHARP	25AS120	N/A	NO START-UP BUT RELAY DOES CLICK	CHECK/REPLACE R752 FOR CHANGE IN VALUE (10k )
SHARP	25AS120	N/A	INTERMITTENT VIDEO	CHECK/RESOLDER CONNECTIONS ON DL2701
SHARP	25AS120	N/A	POWER RELAY FAILURE	INSTALL KIT # BQC-25AM100-1
SHARP	25AS120	N/A	NO TUNING AND NO OSD	CHECK/REPLACE IC1401 (UPC1486C)
SHARP	25AS120	N/A	VENETIAN BLIND EFFECT - HORZ. BARS ACROSS SCREEN	CHECK/REPLACE IC4201 (P/N# RH-IX1705CEZZ)
SHARP	25AS200	N/A	POWER RELAY FAILURE	INSTALL KIT # BQC-25AM100-1
SHARP	25AS200	N/A	INTERMITTENT VIDEO	CHECK/RESOLDER CONNECTIONS ON DL2701
SHARP	25AS200	N/A	STEREO INDICATOR BLINKS ON CERTAIN CABLE SYSTEMS - SOUND ALTERNATES BETWEEN STEREO AND MONO	ADD 680pF (P/N# VCKYPA2HB681K) FROM IC4201 PIN #1 TO GROUND
SHARP	25AS200	N/A	VENETIAN BLIND EFFECT - HORZ. BARS ACROSS SCREEN	CHECK/REPLACE IC4201 (P/N# RH-IX1705CEZZ)
SHARP	25AS200	N/A	NO START-UP BUT RELAY DOES CLICK	CHECK/REPLACE R752 FOR CHANGE IN VALUE (10k )
SHARP	25AS300	N/A	INTERMITTENT VIDEO	CHECK/RESOLDER CONNECTIONS ON DL2701
SHARP	25AS300	N/A	NO START-UP BUT RELAY DOES CLICK	CHECK/REPLACE R752 FOR CHANGE IN VALUE (10k )
SHARP	25AS300	N/A	VENETIAN BLIND EFFECT - HORZ. BARS ACROSS SCREEN	CHECK/REPLACE IC4201 (P/N# RH-IX1705CEZZ)
SHARP	25EM100	N/A	ON SCREEN CUSTOMER ADJUSTMENTS HAVE 3 LEVELS-O%,50%,100% THERE IS NO IN BETWEEN VALUES	CHECK/REPLACE IC2701 (P/N# RH-IX2281CEZZ)
SHARP	25EM100	N/A	HAS OSD BUT NO SOUND OR PICTURE	CHECK/REPLACE D763 (1N4148 OR RH-DX0045GEZZ)
SHARP	25EM100	N/A	IMPROVEMENT OF THE TEXT BOX BLACK LEVEL BACKGROUND	REMOVE D4492 AND REPLACE WITH A 10k 1/8w
SHARP	25EM120	N/A	ON SCREEN CUSTOMER ADJUSTMENTS HAVE 3 LEVELS-O%,50%,100% THERE IS NO IN BETWEEN VALUES	CHECK/REPLACE IC2701 (P/N# RH-IX2281CEZZ)
SHARP	25EM120	N/A	IMPROVEMENT OF THE TEXT BOX BLACK LEVEL BACKGROUND	REMOVE D4492 AND REPLACE WITH A 10k 1/8w
SHARP	25EM120	N/A	HAS OSD BUT NO SOUND OR PICTURE	CHECK/REPLACE D763 (1N4148 OR RH-DX0045GEZZ)
SHARP	25EM150	N/A	HAS OSD BUT NO SOUND OR PICTURE	CHECK/REPLACE D763 (1N4148 OR RH-DX0045GEZZ)
SHARP	25EM40	N/A	HAS OSD BUT NO SOUND OR PICTURE	CHECK/REPLACE D763 (1N4148 OR RH-DX0045GEZZ)
SHARP	25EM40	N/A	IMPROVEMENT OF THE TEXT BOX BLACK LEVEL BACKGROUND	REMOVE D4492 AND REPLACE WITH A 10k 1/8w
SHARP	25EM40	N/A	ON SCREEN CUSTOMER ADJUSTMENTS HAVE 3 LEVELS-O%,50%,100% THERE IS NO IN BETWEEN VALUES	CHECK/REPLACE IC2701 (P/N# RH-IX2281CEZZ)
SHARP	25EM40	N/A	DEAD - NO RELAY CLICK OR ATTEMPT TO TURN ON	CHECK/REPLACE Q2751 (P/N# ECG382)
SHARP	25EM50	N/A	ON SCREEN CUSTOMER ADJUSTMENTS HAVE 3 LEVELS-O%,50%,100% THERE IS NO IN BETWEEN VALUES	CHECK/REPLACE IC2701 (P/N# RH-IX2281CEZZ)
SHARP	25EM50	N/A	DEAD - NO RELAY CLICK OR ATTEMPT TO TURN ON	CHECK/REPLACE Q2751 (P/N# ECG382)
SHARP	25EM50	N/A	IMPROVEMENT OF THE TEXT BOX BLACK LEVEL BACKGROUND	REMOVE D4492 AND REPLACE WITH A 10k 1/8w
SHARP	25EM50	N/A	HAS OSD BUT NO SOUND OR PICTURE	CHECK/REPLACE D763 (1N4148 OR RH-DX0045GEZZ)
SHARP	25ES110	N/A	ON SCREEN CUSTOMER ADJUSTMENTS HAVE 3 LEVELS-O%,50%,100% THERE IS NO IN BETWEEN VALUES	CHECK/REPLACE IC2701 (P/N# RH-IX2281CEZZ)
SHARP	25ES110	N/A	IMPROVEMENT OF THE TEXT BOX BLACK LEVEL BACKGROUND	REMOVE D4492 AND REPLACE WITH A 10k 1/8w
SHARP	25ES130	N/A	IMPROVEMENT OF THE TEXT BOX BLACK LEVEL BACKGROUND	REMOVE D4492 AND REPLACE WITH A 10k 1/8w
SHARP	25ES130	N/A	ON SCREEN CUSTOMER ADJUSTMENTS HAVE 3 LEVELS-O%,50%,100% THERE IS NO IN BETWEEN VALUES	CHECK/REPLACE IC2701 (P/N# RH-IX2281CEZZ)
SHARP	25ES200	N/A	DEAD SET - NO ATTEMPT TO START UP	CHECK/REPLACE IC4201 (P/N# RH-IX2169CENA)
SHARP	25ES200	N/A	IMPROVEMENT OF THE TEXT BOX BLACK LEVEL BACKGROUND	REMOVE D4492 AND REPLACE WITH A 10k 1/8w
SHARP	25ES200	N/A	ON SCREEN CUSTOMER ADJUSTMENTS HAVE 3 LEVELS-O%,50%,100% THERE IS NO IN BETWEEN VALUES	CHECK/REPLACE IC2701 (P/N# RH-IX2281CEZZ)
SHARP	25ES40	N/A	DEAD - NO RELAY CLICK OR ATTEMPT TO TURN ON	CHECK/REPLACE Q2751 (P/N# ECG382)
SHARP	25ES40	N/A	ON SCREEN CUSTOMER ADJUSTMENTS HAVE 3 LEVELS-O%,50%,100% THERE IS NO IN BETWEEN VALUES	CHECK/REPLACE IC2701 (P/N# RH-IX2281CEZZ)
SHARP	25ES40	N/A	PICTURE PULLED IN ON ALL 4 SIDES AND SET MAKES A BUZZING SOUND	CHECK/REPLACE IC701 (P/N# RH-IX0758CEZZ)
SHARP	25ES40	N/A	IMPROVEMENT OF THE TEXT BOX BLACK LEVEL BACKGROUND	REMOVE D4492 AND REPLACE WITH A 10k 1/8w
SHARP	25ES50	N/A	PICTURE PULLED IN ON ALL 4 SIDES AND SET MAKES A BUZZING SOUND	CHECK/REPLACE IC701 (P/N# RH-IX0758CEZZ)
SHARP	25ES50	N/A	IMPROVEMENT OF THE TEXT BOX BLACK LEVEL BACKGROUND	REMOVE D4492 AND REPLACE WITH A 10k 1/8w
SHARP	25ES50	N/A	ON SCREEN CUSTOMER ADJUSTMENTS HAVE 3 LEVELS-O%,50%,100% THERE IS NO IN BETWEEN VALUES	CHECK/REPLACE IC2701 (P/N# RH-IX2281CEZZ)
SHARP	25ES50	N/A	DEAD - NO RELAY CLICK OR ATTEMPT TO TURN ON	CHECK/REPLACE Q2751 (P/N# ECG382)
SHARP	25ES50	N/A	DEAD SET - NO ATTEMPT TO START UP	CHECK/REPLACE IC4201 (P/N# RH-IX2169CENA)
SHARP	25FM100	N/A	SET SHUTS DOWN WHEN TURNED ON	CHECK/REPLACE C710 FOR OPEN
SHARP	25FM100	N/A	NO PICTURE - DOES HAVE SOUND AND H.V.	CHECK/RESOLDER CONNECTIONS ON R724
SHARP	25FM120	N/A	SET SHUTS DOWN WHEN TURNED ON	CHECK/REPLACE C710 FOR OPEN
SHARP	25FM120	N/A	NO PICTURE - DOES HAVE SOUND AND H.V.	CHECK/RESOLDER CONNECTIONS ON R724
SHARP	25FM150	N/A	SET SHUTS DOWN WHEN TURNED ON	CHECK/REPLACE C710 FOR OPEN
SHARP	25FM40	N/A	NO PICTURE - DOES HAVE SOUND AND H.V.	CHECK/RESOLDER CONNECTIONS ON R724
SHARP	25FM40	N/A	SET SHUTS DOWN WHEN TURNED ON	CHECK/REPLACE C710 FOR OPEN
SHARP	25FM50	N/A	SET SHUTS DOWN WHEN TURNED ON	CHECK/REPLACE C710 FOR OPEN
SHARP	25FM50	N/A	NO PICTURE - DOES HAVE SOUND AND H.V.	CHECK/RESOLDER CONNECTIONS ON R724
SHARP	25FS100	N/A	AUDIO BUZZ WHEN USING AUDIO OUTPUT JACKS	REMOVE JUMPER (JA402 AND REPLACE W/ 82 ),REMOVE C1355 AND REPLACE W/ 330uF @ 16v - OR INSTALL (P/N# VRD-RA2BE/KIT)
SHARP	25FS100	N/A	SHORT VERTICAL SWEEP AT TOP AND BOTTOM	CHECK/REPLACE IC751 (9 VOLT REGULATOR) (P/N# VHITA7809S/-1)
SHARP	25FS100	N/A	DISTORTED PICTURE - NO SYNC	CHECK/REPLACE IC201 (P/N# RH-IX2429CEZZ)
SHARP	25FS100	N/A	33 VOLT TUNING PIN 'VT' ON TUNER IS SHORTED, USUALLY AFTER AN ELECTRICAL SURGE OR STORM	CHECK/REPLACE TUNER (P/N# VTUVTSH6UZFC/) AND ADD KIT TO PREVENT FROM REOCCURENCE (P/N# BQC-27FS50//1)
SHARP	25FS100	N/A	AUDIO BUZZ WHEN USING AUDIO OUTPUT JACKS THROUGH A STEREO SYSTEM	INSTALL KIT (VRD-RA2BE/KIT) OR REPLACE JUMPER JA402 WITH 82 AND REPLACE C1355 WITH A 330uF @ 16v CAPACITOR
SHARP	25FS100	N/A	SHORT VERTICAL SWEEP AT BOTTOM AND STRETCHED VERTICAL AT THE TOP	CHECK TO MAKE SURE THAT S501 SWITCH IS IN THE DETENT POSITION AND NOT HALF WAY BETWEEN POSITIONS
SHARP	25FS100	N/A	BLANK RASTER - NO SOUND OR PICTURE - OSD WORKS FINE	CHECK AGC REGISTER S8 FOR A VALUE OF 32 - MOMENTARILY SHORT TP2001 TO TP2002 - CHANGE 'S' WITH CHANNEL & 'D' WITH VOL.
SHARP	25FS120	N/A	SHORT VERTICAL SWEEP AT BOTTOM AND STRETCHED VERTICAL AT THE TOP	CHECK TO MAKE SURE THAT S501 SWITCH IS IN THE DETENT POSITION AND NOT HALF WAY BETWEEN POSITIONS
SHARP	25FS120	N/A	SHORT VERTICAL SWEEP AT TOP AND BOTTOM	CHECK/REPLACE IC751 (9 VOLT REGULATOR) (P/N# VHITA7809S/-1)
SHARP	25FS120	N/A	DISTORTED PICTURE - NO SYNC	CHECK/REPLACE IC201 (P/N# RH-IX2429CEZZ)
SHARP	25FS120	N/A	AUDIO BUZZ WHEN USING AUDIO OUTPUT JACKS THROUGH A STEREO SYSTEM	INSTALL KIT (VRD-RA2BE/KIT) OR REPLACE JUMPER JA402 WITH 82 AND REPLACE C1355 WITH A 330uF @ 16v CAPACITOR
SHARP	25FS120	N/A	33 VOLT TUNING PIN 'VT' ON TUNER IS SHORTED, USUALLY AFTER AN ELECTRICAL SURGE OR STORM	CHECK/REPLACE TUNER (P/N# VTUVTSH6UZFC/) AND ADD KIT TO PREVENT FROM REOCCURENCE (P/N# BQC-27FS50//1)
SHARP	25FS120	N/A	BLANK RASTER - NO SOUND OR PICTURE - OSD WORKS FINE	CHECK AGC REGISTER S8 FOR A VALUE OF 32 - MOMENTARILY SHORT TP2001 TO TP2002 - CHANGE 'S' WITH CHANNEL & 'D' WITH VOL.
SHARP	25FS120	N/A	AUDIO BUZZ WHEN USING AUDIO OUTPUT JACKS	REMOVE JUMPER (JA402 AND REPLACE W/ 82 ),REMOVE C1355 AND REPLACE W/ 330uF @ 16v - OR INSTALL (P/N# VRD-RA2BE/KIT)
SHARP	25FS150	N/A	SHORT VERTICAL SWEEP AT BOTTOM AND STRETCHED VERTICAL AT THE TOP	CHECK TO MAKE SURE THAT S501 SWITCH IS IN THE DETENT POSITION AND NOT HALF WAY BETWEEN POSITIONS
SHARP	25FS150	N/A	SHORT VERTICAL SWEEP AT TOP AND BOTTOM	CHECK/REPLACE IC751 (9 VOLT REGULATOR) (P/N# VHITA7809S/-1)
SHARP	25FS150	N/A	BLANK RASTER - NO SOUND OR PICTURE - OSD WORKS FINE	CHECK AGC REGISTER S8 FOR A VALUE OF 32 - MOMENTARILY SHORT TP2001 TO TP2002 - CHANGE 'S' WITH CHANNEL & 'D' WITH VOL.
SHARP	25FS150	N/A	DISTORTED PICTURE - NO SYNC	CHECK/REPLACE IC201 (P/N# RH-IX2429CEZZ)
SHARP	25FS200	N/A	BLANK RASTER - NO SOUND OR PICTURE - OSD WORKS FINE	CHECK AGC REGISTER S8 FOR A VALUE OF 32 - MOMENTARILY SHORT TP2001 TO TP2002 - CHANGE 'S' WITH CHANNEL & 'D' WITH VOL.
SHARP	25FS200	N/A	SHORT VERTICAL SWEEP AT TOP AND BOTTOM	CHECK/REPLACE IC751 (9 VOLT REGULATOR) (P/N# VHITA7809S/-1)
SHARP	25FS200	N/A	DISTORTED PICTURE - NO SYNC	CHECK/REPLACE IC201 (P/N# RH-IX2429CEZZ)
SHARP	25FS200	N/A	SHORT VERTICAL SWEEP AT BOTTOM AND STRETCHED VERTICAL AT THE TOP	CHECK TO MAKE SURE THAT S501 SWITCH IS IN THE DETENT POSITION AND NOT HALF WAY BETWEEN POSITIONS
SHARP	25FS300	N/A	DISTORTED PICTURE - NO SYNC	CHECK/REPLACE IC201 (P/N# RH-IX2429CEZZ)
SHARP	25FS300	N/A	SHORT VERTICAL SWEEP AT BOTTOM AND STRETCHED VERTICAL AT THE TOP	CHECK TO MAKE SURE THAT S501 SWITCH IS IN THE DETENT POSITION AND NOT HALF WAY BETWEEN POSITIONS
SHARP	25FS300	N/A	BLANK RASTER - NO SOUND OR PICTURE - OSD WORKS FINE	CHECK AGC REGISTER S8 FOR A VALUE OF 32 - MOMENTARILY SHORT TP2001 TO TP2002 - CHANGE 'S' WITH CHANNEL & 'D' WITH VOL.
SHARP	25FS300	N/A	SHORT VERTICAL SWEEP AT TOP AND BOTTOM	CHECK/REPLACE IC751 (9 VOLT REGULATOR) (P/N# VHITA7809S/-1)
SHARP	25FS40	N/A	SHORT VERTICAL SWEEP AT TOP AND BOTTOM	CHECK/REPLACE IC751 (9 VOLT REGULATOR) (P/N# VHITA7809S/-1)
SHARP	25FS40	N/A	BLANK RASTER - NO SOUND OR PICTURE - OSD WORKS FINE	CHECK AGC REGISTER S8 FOR A VALUE OF 32 - MOMENTARILY SHORT TP2001 TO TP2002 - CHANGE 'S' WITH CHANNEL & 'D' WITH VOL.
SHARP	25FS40	N/A	DISTORTED PICTURE - NO SYNC	CHECK/REPLACE IC201 (P/N# RH-IX2429CEZZ)
SHARP	25FS40	N/A	SHORT VERTICAL SWEEP AT BOTTOM AND STRETCHED VERTICAL AT THE TOP	CHECK TO MAKE SURE THAT S501 SWITCH IS IN THE DETENT POSITION AND NOT HALF WAY BETWEEN POSITIONS
SHARP	25FS50	N/A	BLANK RASTER - NO SOUND OR PICTURE - OSD WORKS FINE	CHECK AGC REGISTER S8 FOR A VALUE OF 32 - MOMENTARILY SHORT TP2001 TO TP2002 - CHANGE 'S' WITH CHANNEL & 'D' WITH VOL.
SHARP	25FS50	N/A	SHORT VERTICAL SWEEP AT BOTTOM AND STRETCHED VERTICAL AT THE TOP	CHECK TO MAKE SURE THAT S501 SWITCH IS IN THE DETENT POSITION AND NOT HALF WAY BETWEEN POSITIONS
SHARP	25FS50	N/A	DISTORTED PICTURE - NO SYNC	CHECK/REPLACE IC201 (P/N# RH-IX2429CEZZ)
SHARP	25FS50	N/A	SHORT VERTICAL SWEEP AT TOP AND BOTTOM	CHECK/REPLACE IC751 (9 VOLT REGULATOR) (P/N# VHITA7809S/-1)
SHARP	25GM100	N/A	DEAD - JUST CLICKS	CHECK/REPLACE Q602 (VS2SD1554//1E) AND R717 (VRW-KQ4AC6R8K)
SHARP	25GM100	N/A	RED 'T' IN THE UPPER RIGHT CORNER OF SCREEN CAUSE BY PRESSING '4' OF ANOTHER MANUFACTURES REMOTE	BEFORE REPL.IC2001, PRESS '4' KEY ON ORIG. REMOTE TO RESET CHECK/REPLACE IC2001 (P/N# RH-IX2552CEN2 OR RH-IX2599CEN2)
SHARP	25GM100	N/A	SHORT VERTICAL SWEEP	CHECK/REPLACE C513 (470uF @ 50v)
SHARP	25GM120	N/A	DEAD - JUST CLICKS	CHECK/REPLACE Q602 (VS2SD1554//1E) AND R717 (VRW-KQ4AC6R8K)
SHARP	25GM120	N/A	SHORT VERTICAL SWEEP	CHECK/REPLACE C513 (470uF @ 50v)
SHARP	25GM120	N/A	RED 'T' IN THE UPPER RIGHT CORNER OF SCREEN CAUSE BY PRESSING '4' OF ANOTHER MANUFACTURES REMOTE	BEFORE REPL.IC2001, PRESS '4' KEY ON ORIG. REMOTE TO RESET CHECK/REPLACE IC2001 (P/N# RH-IX2552CEN2 OR RH-IX2599CEN2)
SHARP	25GM150	N/A	DEAD - JUST CLICKS	CHECK/REPLACE Q602 (VS2SD1554//1E) AND R717 (VRW-KQ4AC6R8K)
SHARP	25GM150	N/A	SHORT VERTICAL SWEEP	CHECK/REPLACE C513 (470uF @ 50v)
SHARP	25GM200	N/A	SHORT VERTICAL SWEEP	CHECK/REPLACE C513 (470uF @ 50v)
SHARP	25GM200	N/A	DEAD - JUST CLICKS	CHECK/REPLACE Q602 (VS2SD1554//1E) AND R717 (VRW-KQ4AC6R8K)
SHARP	25GM60	N/A	SHORT VERTICAL SWEEP	CHECK/REPLACE C513 (470uF @ 50v)
SHARP	25GM60	N/A	NO SOUND BUT PICTURE IS OK - SET MAY EXHIBIT AFT PROBLEMS	GO INTO SERVICE MENU BY SHORTING TP2001 & TP2002, USE CHAN. UP TO ADVANCE TO S33, USE VOL UP/DOWN TO SET TO '00'
SHARP	25GM60	N/A	RED 'T' IN THE UPPER RIGHT CORNER OF SCREEN CAUSE BY PRESSING '4' OF ANOTHER MANUFACTURES REMOTE	BEFORE REPL.IC2001, PRESS '4' KEY ON ORIG. REMOTE TO RESET CHECK/REPLACE IC2001 (P/N# RH-IX2552CEN2 OR RH-IX2599CEN2)
SHARP	25GM60	N/A	DEAD - JUST CLICKS	CHECK/REPLACE Q602 (VS2SD1554//1E) AND R717 (VRW-KQ4AC6R8K)
SHARP	25GM80	N/A	SHORT VERTICAL SWEEP	CHECK/REPLACE C513 (470uF @ 50v)
SHARP	25GM80	N/A	DEAD - JUST CLICKS	CHECK/REPLACE Q602 (VS2SD1554//1E) AND R717 (VRW-KQ4AC6R8K)
SHARP	25GM80	N/A	RED 'T' IN THE UPPER RIGHT CORNER OF SCREEN CAUSE BY PRESSING '4' OF ANOTHER MANUFACTURES REMOTE	BEFORE REPL.IC2001, PRESS '4' KEY ON ORIG. REMOTE TO RESET CHECK/REPLACE IC2001 (P/N# RH-IX2552CEN2 OR RH-IX2599CEN2)
SHARP	25GS100	N/A	DEAD SET	CHECK/REPLACE R706 (150?1/2 watt) (P/N# VRS-RG2HC151)
SHARP	25GS100	N/A	NO SOUND - PICTURE IS FINE	SHORT TP2001 AND TP2002 - ADVANCE ON-SCREEN REGISTER TO #33, - ADJUST SETTING TO #02 INSTEAD OF #00
SHARP	25GS100	N/A	RED 'T' IN THE UPPER RIGHT CORNER OF SCREEN CAUSE BY PRESSING '4' OF ANOTHER MANUFACTURES REMOTE	BEFORE REPL.IC2001, PRESS '4' KEY ON ORIG. REMOTE TO RESET CHECK/REPLACE IC2001 (P/N# RH-IX2552CEN2 OR RH-IX2599CEN2)
SHARP	25GS100	N/A	INTERMITTENTLY SHUTS OFF	CHECK/RESOLDER CONNECTIONS ON PIN #9 & #10 OF FLYBACK
SHARP	25GS100	N/A	NO SOUND BUT PICTURE IS OK - SET MAY EXHIBIT AFT PROBLEMS	GO INTO SERVICE MENU BY SHORTING TP2001 & TP2002, USE CHAN. UP TO ADVANCE TO S33, USE VOL UP/DOWN TO SET TO 'B5'
SHARP	25GS120	N/A	NO SOUND BUT PICTURE IS OK - SET MAY EXHIBIT AFT PROBLEMS	GO INTO SERVICE MENU BY SHORTING TP2001 & TP2002, USE CHAN. UP TO ADVANCE TO S33, USE VOL UP/DOWN TO SET TO 'B5'
SHARP	25GS120	N/A	INTERMITTENTLY SHUTS OFF	CHECK/RESOLDER CONNECTIONS ON PIN #9 & #10 OF FLYBACK
SHARP	25GS120	N/A	RED 'T' IN THE UPPER RIGHT CORNER OF SCREEN CAUSE BY PRESSING '4' OF ANOTHER MANUFACTURES REMOTE	BEFORE REPL.IC2001, PRESS '4' KEY ON ORIG. REMOTE TO RESET CHECK/REPLACE IC2001 (P/N# RH-IX2552CEN2 OR RH-IX2599CEN2)
SHARP	25GS120	N/A	NO SOUND - PICTURE IS FINE	SHORT TP2001 AND TP2002 - ADVANCE ON-SCREEN REGISTER TO #33, - ADJUST SETTING TO #02 INSTEAD OF #00
SHARP	25GS120	N/A	DEAD SET	CHECK/REPLACE R706 (150?1/2 watt) (P/N# VRS-RG2HC151)
SHARP	25GS60	N/A	DEAD SET	CHECK/REPLACE R706 (150?1/2 watt) (P/N# VRS-RG2HC151)
SHARP	25GS60	N/A	NO SOUND - PICTURE IS FINE	SHORT TP2001 AND TP2002 - ADVANCE ON-SCREEN REGISTER TO #33, - ADJUST SETTING TO #02 INSTEAD OF #00
SHARP	25GS60	N/A	INTERMITTENTLY SHUTS OFF	CHECK/RESOLDER CONNECTIONS ON PIN #9 & #10 OF FLYBACK
SHARP	25GS60	N/A	NO SOUND BUT PICTURE IS OK - SET MAY EXHIBIT AFT PROBLEMS	GO INTO SERVICE MENU BY SHORTING TP2001 & TP2002, USE CHAN. UP TO ADVANCE TO S33, USE VOL UP/DOWN TO SET TO '82'
SHARP	25GS80	N/A	NO SOUND BUT PICTURE IS OK - SET MAY EXHIBIT AFT PROBLEMS	GO INTO SERVICE MENU BY SHORTING TP2001 & TP2002, USE CHAN. UP TO ADVANCE TO S33, USE VOL UP/DOWN TO SET TO '9E'
SHARP	25GS80	N/A	NO SOUND - PICTURE IS FINE	SHORT TP2001 AND TP2002 - ADVANCE ON-SCREEN REGISTER TO #33, - ADJUST SETTING TO #02 INSTEAD OF #00
SHARP	25GS80	N/A	DEAD SET	CHECK/REPLACE R706 (150?1/2 watt) (P/N# VRS-RG2HC151)
SHARP	25GS80	N/A	INTERMITTENTLY SHUTS OFF	CHECK/RESOLDER CONNECTIONS ON PIN #9 & #10 OF FLYBACK
SHARP	25H102	N/A	INTERMITTENT OPERATION-ON/OFF ERRATIC-CHANNELS ERRATIC-	CHECK/REPLACE X1201 (455KHz) XTAL --MAY RESPOND TO FREEZE SPRAY.
SHARP	25LC156	N/A	VERT ROLL DURING SCENE CHANGES,COMMERCIALS,SIGNAL CHANGES	CHANGE C453 TO A 0.47uF/50WV WITH NEG. SIDE TO R452 AND POS SIDE TO Q407 EMITTER
SHARP	25LC156	N/A	BUZZING SOUND ON CERTAIN CABLE CHANNELS	ADD 22uH COIL (VP-LK220K0000)IN SERIES WITH 180pF CAP (VCKYPA2HB181K)BETWEEN CF301 AND C301 TO GROUND.
SHARP	25LT16	N/A	RETRACE AT THE TOP OF THE SCREEN	CHECK/REPLACE C510 (47uF @ 63v)
SHARP	25LT16	N/A	BUZZING SOUND ON CERTAIN CABLE CHANNELS	ADD 22uH COIL (VP-LK220K0000)IN SERIES WITH 180pF CAP (VCKYPA2HB181K)BETWEEN CF301 AND C301 TO GROUND.
SHARP	25LT16	N/A	SHORT VERTICAL SWEEP	CHECK/REPLACE C504 & C51 (47uF@63v) AND C509 (100uF@100v)
SHARP	25LT16	N/A	VERT ROLL DURING SCENE CHANGES,COMMERCIALS,SIGNAL CHANGES	CHANGE C453 TO A 0.47uF/50WV WITH NEG. SIDE TO R452 AND POS SIDE TO Q407 EMITTER
SHARP	25LT56	N/A	SHORT VERTICAL SWEEP	CHECK/REPLACE C504 & C51 (47uF@63v) AND C509 (100uF@100v)
SHARP	25LT56	N/A	VERT ROLL DURING SCENE CHANGES,COMMERCIALS,SIGNAL CHANGES	CHANGE C453 TO A 0.47uF/50WV WITH NEG. SIDE TO R452 AND POS SIDE TO Q407 EMITTER
SHARP	25LT56	N/A	BUZZING SOUND ON CERTAIN CABLE CHANNELS	ADD 22uH COIL (VP-LK220K0000)IN SERIES WITH 180pF CAP (VCKYPA2HB181K)BETWEEN CF301 AND C301 TO GROUND.
SHARP	25MC157	N/A	NO HORIZONTAL SWEEP	CHECK/REPLACE C2606 FOR OPEN
SHARP	25MC157	N/A	NO VERTICAL SWEEP - WHITE LINE THRU CENTER	CHECK/REPLACE Q2501,Q2502 AND R2503 OR CONNECTIONS ON OUTPUT TRANSISTORS.
SHARP	25MC157	25L3	LINES AT TOP OF THE SCREEN AND SHORT VERTICAL SWEEP	CHECK/REPLACE C2505 AND C2508
SHARP	25MT157	25L3	NO VERTICAL SWEEP	CHECK/REPLACE Q502,Q503,R508,R507,R518,R515 AND D503
SHARP	25MT17	N/A	NO VERTICAL SWEEP - WHITE LINE THRU CENTER	CHECK/REPLACE Q2501,Q2502 AND R2503 OR CONNECTIONS ON OUTPUT TRANSISTORS.
SHARP	25MT17	N/A	NO HORIZONTAL SWEEP	CHECK/REPLACE C2606 FOR OPEN
SHARP	25MT17	25L1	LINES AT TOP OF THE SCREEN AND SHORT VERTICAL SWEEP	CHECK/REPLACE C2505 AND C2508
SHARP	25MT17	25L1	NO VERTICAL SWEEP	CHECK/REPLACE Q502,Q503,R508,R507,R518,R515 AND D503
SHARP	25MT57	N/A	NO VERTICAL SWEEP - WHITE LINE THRU CENTER	CHECK/REPLACE Q2501,Q2502 AND R2503 OR CONNECTIONS ON OUTPUT TRANSISTORS.
SHARP	25MT57	N/A	NO HORIZONTAL SWEEP	CHECK/REPLACE C2606 FOR OPEN
SHARP	25MT57	25L2	LINES AT TOP OF THE SCREEN AND SHORT VERTICAL SWEEP	CHECK/REPLACE C2505 AND C2508
SHARP	25MT57	25L2	NO VERTICAL SWEEP	CHECK/REPLACE Q502,Q503,R508,R507,R518,R515 AND D503
SHARP	25NC158	N/A	NO VERT SWEEP	CHECK C507 FOR OPEN OR CONNECTIONS
SHARP	25NC158	N/A	ONLY SNOW - WON'T TUNE A CHANNEL	IF VT LINE IS LOW OR MISSING THEN REPLACE IC1401
SHARP	25NC158	N/A	NO AUDIO - PIX NORMAL	CHECK R337 FOR OPEN OR SOLDER CONNECTIONS
SHARP	25NC158	N/A	NO VHF LOW BAND OR NO VHF HIGH BAND	REPLACE VARACTOR TUNER
SHARP	25NC168	N/A	NO AUDIO - PIX NORMAL	CHECK R337 FOR OPEN OR SOLDER CONNECTIONS
SHARP	25NC168	N/A	NO VHF LOW BAND OR NO VHF HIGH BAND	REPLACE VARACTOR TUNER
SHARP	25NC168	N/A	ONLY SNOW - WON'T TUNE A CHANNEL	IF VT LINE IS LOW OR MISSING THEN REPLACE IC1401
SHARP	25NC168	N/A	NO VERT SWEEP	CHECK C507 FOR OPEN OR CONNECTIONS
SHARP	25NC178	N/A	NO VERT SWEEP	CHECK C507 FOR OPEN OR CONNECTIONS
SHARP	25NC178	N/A	NO AUDIO - PIX NORMAL	CHECK R337 FOR OPEN OR SOLDER CONNECTIONS
SHARP	25NC178	N/A	ONLY SNOW - WON'T TUNE A CHANNEL	IF VT LINE IS LOW OR MISSING THEN REPLACE IC1401
SHARP	25NC178	N/A	NO VHF LOW BAND OR NO VHF HIGH BAND	REPLACE VARACTOR TUNER
SHARP	25NC278	N/A	NO AUDIO - PIX NORMAL	CHECK R337 FOR OPEN OR SOLDER CONNECTIONS
SHARP	25NC278	N/A	NO VERT SWEEP	CHECK C507 FOR OPEN OR CONNECTIONS
SHARP	25NC278	N/A	ONLY SNOW - WON'T TUNE A CHANNEL	IF VT LINE IS LOW OR MISSING THEN REPLACE IC1401
SHARP	25NC278	N/A	NO VHF LOW BAND OR NO VHF HIGH BAND	REPLACE VARACTOR TUNER
SHARP	25NV68	N/A	SEVERE HORZ. TEARING - MAY BE INTERMITTENT - SET SHUTS DOWN	CHECK/REPLACE IC701 (RH-IZ0027CEZZ)
SHARP	25RC	ALL 25RC'S	TV SHUTSDOWN FOR NO APPARENT REASON	CHECK/REPLACE R628 (1.2k/3WATT) FOR INTERMITTENT
SHARP	25RC119	N/A	NARROW PIX EITHER VERT. OR HORZ.	CHECK CONNECTIONS ON Q531,Q532 AND Q631
SHARP	25RC119	N/A	INTERMITTENT SHUTDOWN	ADD KIT# BQC-25RV69/-1 ,CHANGE R633 TO 6.8k, REMOVE J423 AND ADD 2.7 ohm 15 watt IN ITS PLACE.
SHARP	25RC119	N/A	INTERMITTENTLY WILL NOT TUNE ANYTHING BUT CABLE CHANNEL 30 BUT OSD CHANNEL NUMBER DOESN'T MATCH THE TUNED CHANNEL	CHECK/REPLACE L1401 FOR INTERMITTENT OPENING
SHARP	25RC119	N/A	AUDIO AND OSD ARE FINE BUT NO VIDEO - DOES HAVE CHROMA	CHECK/REPLACE IC201
SHARP	25RC169	N/A	NARROW PIX EITHER VERT. OR HORZ.	CHECK CONNECTIONS ON Q531,Q532 AND Q631
SHARP	25RC169	N/A	INTERMITTENTLY WILL NOT TUNE ANYTHING BUT CABLE CHANNEL 30 BUT OSD CHANNEL NUMBER DOESN'T MATCH THE TUNED CHANNEL	CHECK/REPLACE L1401 FOR INTERMITTENT OPENING
SHARP	25RC169	N/A	INTERMITTENT SHUTDOWN	ADD KIT# BQC-25RV69/-1 ,CHANGE R633 TO 6.8k, REMOVE J423 AND ADD 2.7 ohm 15 watt IN ITS PLACE.
SHARP	25RC169	N/A	AUDIO AND OSD ARE FINE BUT NO VIDEO - DOES HAVE CHROMA	CHECK/REPLACE IC201
SHARP	25RC179	N/A	NARROW PIX EITHER VERT. OR HORZ.	CHECK CONNECTIONS ON Q531,Q532 AND Q631
SHARP	25RC179	N/A	AUDIO AND OSD ARE FINE BUT NO VIDEO - DOES HAVE CHROMA	CHECK/REPLACE IC201
SHARP	25RC179	N/A	INTERMITTENT SHUTDOWN	ADD KIT# BQC-25RV69/-1 ,CHANGE R633 TO 6.8k, REMOVE J423 AND ADD 2.7 ohm 15 watt IN ITS PLACE.
SHARP	25RC179	N/A	INTERMITTENTLY WILL NOT TUNE ANYTHING BUT CABLE CHANNEL 30 BUT OSD CHANNEL NUMBER DOESN'T MATCH THE TUNED CHANNEL	CHECK/REPLACE L1401 FOR INTERMITTENT OPENING
SHARP	25RC219	N/A	INTERMITTENT SHUTDOWN	ADD KIT# BQC-25RV69/-1 ,CHANGE R633 TO 6.8k, REMOVE J423 AND ADD 2.7 ohm 15 watt IN ITS PLACE.
SHARP	25RC219	N/A	NARROW PIX EITHER VERT. OR HORZ.	CHECK CONNECTIONS ON Q531,Q532 AND Q631
SHARP	25RC279	N/A	INTERMITTENT SHUTDOWN	ADD KIT# BQC-25RV69/-1 ,CHANGE R633 TO 6.8k, REMOVE J423 AND ADD 2.7 ohm 15 watt IN ITS PLACE.
SHARP	25RC279	N/A	NARROW PIX EITHER VERT. OR HORZ.	CHECK CONNECTIONS ON Q531,Q532 AND Q631
SHARP	25RC280	N/A	NARROW PIX EITHER VERT. OR HORZ.	CHECK CONNECTIONS ON Q531,Q532 AND Q631
SHARP	25RC280	N/A	INTERMITTENT SHUTDOWN	ADD KIT# BQC-25RV69/-1 ,CHANGE R633 TO 6.8k, REMOVE J423 AND ADD 2.7 ohm 15 watt IN ITS PLACE.
SHARP	25RT59	N/A	INTERMITTENT VERTICAL SWEEP	CHECK/RESOLDER CONNECTIONS ON VERTICAL OUTPUT XSTRS.
SHARP	25RT59	N/A	SHORT VERTICAL SWEEP	CHECK/REPLACE C513 AND C516 (47uF @ 63v)
SHARP	25RT59	N/A	NO VERTICAL SWEEP - WHITE LINE THRU CENTER	CHECK/REPLACE Q2501,Q2502 AND R2503 OR CONNECTIONS ON OUTPUT TRANSISTORS.
SHARP	25RT59	N/A	CLICKING NOISE OR SHUTDOWN	CHECK/REPLACE IC701 WITH A RH-IZ0073CEZZ - CHANGE R414 TO 1.2k AND R616 TO 5.6k
SHARP	25RT59	N/A	CO-CHANNEL INTERFERENCE	REPLACE ANTENNA BLOCK (P/N # RUNTK0371CEZZ)
SHARP	25RT59	N/A	CO-CHANNEL INTERFERENCE	CHECK/REPLACE ANTENNA BLOCK (RUNTK0371CEZZ)
SHARP	25RV119	N/A	AUDIO AND OSD ARE FINE BUT NO VIDEO - DOES HAVE CHROMA	CHECK/REPLACE IC201
SHARP	25RV629	N/A	INTERMITTENT SHUTDOWN	ADD KIT# BQC-25RV69/-1 ,CHANGE R633 TO 6.8k, REMOVE J423 AND ADD 2.7 ohm 15 watt IN ITS PLACE.
SHARP	25RV629	N/A	CO-CHANNEL INTERFERENCE	REPLACE ANTENNA BLOCK (P/N # RUNTK0371CEZZ)
SHARP	25RV629	N/A	NARROW PIX EITHER VERT. OR HORZ.	CHECK CONNECTIONS ON Q531,Q532 AND Q631
SHARP	25RV629	N/A	WILL NOT TUNE - MISSING TUNING VOLTAGE	CHECK/REPLACE R1405 OPEN (10k )
SHARP	25RV629	N/A	CO-CHANNEL INTERFERENCE	CHECK/REPLACE ANTENNA BLOCK (RUNTK0371CEZZ)
SHARP	25RV69	N/A	NARROW PIX EITHER VERT. OR HORZ.	CHECK CONNECTIONS ON Q531,Q532 AND Q631
SHARP	25RV69	N/A	INTERMITTENT SHUTDOWN	ADD KIT# BQC-25RV69/-1 ,CHANGE R633 TO 6.8k, REMOVE J423 AND ADD 2.7 ohm 15 watt IN ITS PLACE.
SHARP	25RV69	N/A	WILL NOT TUNE - MISSING TUNING VOLTAGE	CHECK/REPLACE R1405 OPEN (10k )
SHARP	25RV69	N/A	CO-CHANNEL INTERFERENCE	CHECK/REPLACE ANTENNA BLOCK (RUNTK0371CEZZ)
SHARP	25RV69	N/A	SEVERE HORZ. TEARING - MAY BE INTERMITTENT - SET SHUTS DOWN	CHECK/REPLACE IC701 (RH-IZ0027CEZZ)
SHARP	25RV69	N/A	CO-CHANNEL INTERFERENCE	REPLACE ANTENNA BLOCK (P/N # RUNTK0371CEZZ)
SHARP	25RV79	N/A	NARROW PIX EITHER VERT. OR HORZ.	CHECK CONNECTIONS ON Q531,Q532 AND Q631
SHARP	25RV79	N/A	CO-CHANNEL INTERFERENCE	CHECK/REPLACE ANTENNA BLOCK (RUNTK0371CEZZ)
SHARP	25RV79	N/A	CO-CHANNEL INTERFERENCE	REPLACE ANTENNA BLOCK (P/N # RUNTK0371CEZZ)
SHARP	25RV79	N/A	INTERMITTENT SHUTDOWN	ADD KIT# BQC-25RV69/-1 ,CHANGE R633 TO 6.8k, REMOVE J423 AND ADD 2.7 ohm 15 watt IN ITS PLACE.
SHARP	25SB60	N/A	POWER RELAY FAILURE	INSTALL KIT # BQC-25SB60/-1
SHARP	25SB60	N/A	NO VERTICAL SWEEP	CHECK/REPLACE IC551 (P/N# ECG1782), D551 (P/N# ECG552), R563 (1?@ 1 watt)
SHARP	25SB60B	N/A	DEAD SET WITH NO CLICK	CHECK/REPLACE Q1501,D767 AND RY751 FOR OPEN COIL
SHARP	25SB60B	N/A	POWER RELAY FAILURE	INSTALL KIT # BQC-25SB60/-1
SHARP	25SB610	N/A	NO VERTICAL SWEEP	CHECK/REPLACE IC551 (P/N# ECG1782), D551 (P/N# ECG552), R563 (1?@ 1 watt)
SHARP	25SB610	N/A	POWER RELAY FAILURE	INSTALL KIT # BQC-25SB60/-1
SHARP	25SB610B	N/A	DEAD SET WITH NO CLICK	CHECK/REPLACE Q1501,D767 AND RY751 FOR OPEN COIL
SHARP	25SB620	N/A	NO VERTICAL SWEEP	CHECK/REPLACE IC551 (P/N# ECG1782), D551 (P/N# ECG552), R563 (1?@ 1 watt)
SHARP	25SB620	N/A	POWER RELAY FAILURE	INSTALL KIT # BQC-25SB60/-1
SHARP	25SB620B	N/A	DEAD SET WITH NO CLICK	CHECK/REPLACE Q1501,D767 AND RY751 FOR OPEN COIL
SHARP	25SB620B	N/A	POWER RELAY FAILURE	INSTALL KIT # BQC-25SB60/-1
SHARP	25SB640	N/A	NO VERTICAL SWEEP	CHECK/REPLACE IC551 (P/N# ECG1782), D551 (P/N# ECG552), R563 (1?@ 1 watt)
SHARP	25SB640	N/A	POWER RELAY FAILURE	INSTALL KIT # BQC-25SB60/-1
SHARP	25SB640B	N/A	POWER RELAY FAILURE	INSTALL KIT # BQC-25SB60/-1
SHARP	25SB640B	N/A	DEAD SET WITH NO CLICK	CHECK/REPLACE Q1501,D767 AND RY751 FOR OPEN COIL
SHARP	25SB70	N/A	POWER RELAY FAILURE	INSTALL KIT # BQC-25SB60/-1
SHARP	25SB70B	N/A	POWER RELAY FAILURE	INSTALL KIT # BQC-25SB60/-1
SHARP	25SB710	N/A	POWER RELAY FAILURE	INSTALL KIT # BQC-25SB60/-1
SHARP	25SB710B	N/A	POWER RELAY FAILURE	INSTALL KIT # BQC-25SB60/-1
SHARP	25SB720	N/A	POWER RELAY FAILURE	INSTALL KIT # BQC-25SB60/-1
SHARP	25SB720B	N/A	POWER RELAY FAILURE	INSTALL KIT # BQC-25SB60/-1
SHARP	25SB740	N/A	POWER RELAY FAILURE	INSTALL KIT # BQC-25SB60/-1
SHARP	25SB740B	N/A	POWER RELAY FAILURE	INSTALL KIT # BQC-25SB60/-1
SHARP	27AS100	N/A	AUDIO DISTORTION OR BUZZ IN AUDIO ON SCENES WITH WHITE SUBTITLES	REMOVE JUMPER RJ10 (NEAR PIN # 11 OF THE 'SA' CONNECTOR' MAY BE A STAPLE OR A SURFACE MOUNT DEVICE
SHARP	27AS100	N/A	POWER RELAY FAILURE	INSTALL KIT # BQC-25AM100-1
SHARP	27AS100	N/A	INTERMITTENT VIDEO	CHECK/RESOLDER CONNECTIONS ON DL2701
SHARP	27AS100	N/A	STEREO INDICATOR BLINKS ON CERTAIN CABLE SYSTEMS - SOUND ALTERNATES BETWEEN STEREO AND MONO	ADD 680pF (P/N# VCKYPA2HB681K) FROM IC4201 PIN #1 TO GROUND
SHARP	27AS120	N/A	AUDIO DISTORTION OR BUZZ IN AUDIO ON SCENES WITH WHITE SUBTITLES	REMOVE JUMPER RJ10 (NEAR PIN # 11 OF THE 'SA' CONNECTOR' MAY BE A STAPLE OR A SURFACE MOUNT DEVICE
SHARP	27AS120	N/A	POWER RELAY FAILURE	INSTALL KIT # BQC-25AM100-1
SHARP	27AS120	N/A	INTERMITTENT VIDEO	CHECK/RESOLDER CONNECTIONS ON DL2701
SHARP	27AS120	N/A	STEREO INDICATOR BLINKS ON CERTAIN CABLE SYSTEMS - SOUND ALTERNATES BETWEEN STEREO AND MONO	ADD 680pF (P/N# VCKYPA2HB681K) FROM IC4201 PIN #1 TO GROUND
SHARP	27AS200	N/A	INTERMITTENT VIDEO	CHECK/RESOLDER CONNECTIONS ON DL2701
SHARP	27AS300	N/A	POWER RELAY FAILURE	INSTALL KIT # BQC-25AM100-1
SHARP	27AS300	N/A	STEREO INDICATOR BLINKS ON CERTAIN CABLE SYSTEMS - SOUND ALTERNATES BETWEEN STEREO AND MONO	ADD 680pF (P/N# VCKYPA2HB681K) FROM IC4201 PIN #1 TO GROUND
SHARP	27AS300	N/A	INTERMITTENT VIDEO	CHECK/RESOLDER CONNECTIONS ON DL2701
SHARP	27ES100	N/A	ON SCREEN CUSTOMER ADJUSTMENTS HAVE 3 LEVELS-O%,50%,100% THERE IS NO IN BETWEEN VALUES	CHECK/REPLACE IC2701 (P/N# RH-IX2281CEZZ)
SHARP	27ES100	N/A	DEAD SET - NO ATTEMPT TO START UP	CHECK/REPLACE IC4201 (P/N# RH-IX2169CEZZ)
SHARP	27ES100	N/A	IMPROVEMENT OF THE TEXT BOX BLACK LEVEL BACKGROUND	REMOVE D4492 AND REPLACE WITH A 10k 1/8w
SHARP	27ES120	N/A	ON SCREEN CUSTOMER ADJUSTMENTS HAVE 3 LEVELS-O%,50%,100% THERE IS NO IN BETWEEN VALUES	CHECK/REPLACE IC2701 (P/N# RH-IX2281CEZZ)
SHARP	27ES120	N/A	IMPROVEMENT OF THE TEXT BOX BLACK LEVEL BACKGROUND	REMOVE D4492 AND REPLACE WITH A 10k 1/8w
SHARP	27ES120	N/A	DEAD SET - NO ATTEMPT TO START UP	CHECK/REPLACE IC4201 (P/N# RH-IX2169CEZZ)
SHARP	27ES50	N/A	ON SCREEN CUSTOMER ADJUSTMENTS HAVE 3 LEVELS-O%,50%,100% THERE IS NO IN BETWEEN VALUES	CHECK/REPLACE IC2701 (P/N# RH-IX2281CEZZ)
SHARP	27ES50	N/A	DEAD SET - NO ATTEMPT TO START UP	CHECK/REPLACE IC4201 (P/N# RH-IX2169CEZZ)
SHARP	27ES50	N/A	IMPROVEMENT OF THE TEXT BOX BLACK LEVEL BACKGROUND	REMOVE D4492 AND REPLACE WITH A 10k 1/8w
SHARP	27FM100	N/A	SET SHUTS DOWN WHEN TURNED ON	CHECK/REPLACE C710 FOR OPEN
SHARP	27FM120	N/A	SET SHUTS DOWN WHEN TURNED ON	CHECK/REPLACE C710 FOR OPEN
SHARP	27FM150	N/A	SET SHUTS DOWN WHEN TURNED ON	CHECK/REPLACE C710 FOR OPEN
SHARP	27FM40	N/A	SET SHUTS DOWN WHEN TURNED ON	CHECK/REPLACE C710 FOR OPEN
SHARP	27FM50	N/A	SET SHUTS DOWN WHEN TURNED ON	CHECK/REPLACE C710 FOR OPEN
SHARP	27FS100	N/A	33 VOLT TUNING PIN 'VT' ON TUNER IS SHORTED, USUALLY AFTER AN ELECTRICAL SURGE OR STORM	CHECK/REPLACE TUNER (P/N# VTUVTSH6UZFC/) AND ADD KIT TO PREVENT FROM REOCCURENCE (P/N# BQC-27FS50//1)
SHARP	27FS100	N/A	BLANK RASTER - NO SOUND OR PICTURE - OSD WORKS FINE	CHECK AGC REGISTER S8 FOR A VALUE OF 32 - MOMENTARILY SHORT TP2001 TO TP2002 - CHANGE 'S' WITH CHANNEL & 'D' WITH VOL.
SHARP	27FS100	N/A	SHORT VERTICAL SWEEP AT TOP AND BOTTOM	CHECK/REPLACE IC751 (9 VOLT REGULATOR) (P/N# VHITA7809S/-1)
SHARP	27FS100	N/A	AUDIO BUZZ WHEN USING AUDIO OUTPUT JACKS	REMOVE JUMPER (JA402 AND REPLACE W/ 82 ),REMOVE C1355 AND REPLACE W/ 330uF @ 16v - OR INSTALL (P/N# VRD-RA2BE/KIT)
SHARP	27FS100	N/A	AUDIO BUZZ WHEN USING AUDIO OUTPUT JACKS THROUGH A STEREO SYSTEM	INSTALL KIT (VRD-RA2BE/KIT) OR REPLACE JUMPER JA402 WITH 82 AND REPLACE C1355 WITH A 330uF @ 16v CAPACITOR
SHARP	27FS100	N/A	SHORT VERTICAL SWEEP AT BOTTOM AND STRETCHED VERTICAL AT THE TOP	CHECK TO MAKE SURE THAT S501 SWITCH IS IN THE DETENT POSITION AND NOT HALF WAY BETWEEN POSITIONS
SHARP	27FS100	N/A	DISTORTED PICTURE - NO SYNC	CHECK/REPLACE IC201 (P/N# RH-IX2429CEZZ)
SHARP	27FS120	N/A	AUDIO BUZZ WHEN USING AUDIO OUTPUT JACKS	REMOVE JUMPER (JA402 AND REPLACE W/ 82 ),REMOVE C1355 AND REPLACE W/ 330uF @ 16v - OR INSTALL (P/N# VRD-RA2BE/KIT)
SHARP	27FS120	N/A	SHORT VERTICAL SWEEP AT BOTTOM AND STRETCHED VERTICAL AT THE TOP	CHECK TO MAKE SURE THAT S501 SWITCH IS IN THE DETENT POSITION AND NOT HALF WAY BETWEEN POSITIONS
SHARP	27FS120	N/A	BLANK RASTER - NO SOUND OR PICTURE - OSD WORKS FINE	CHECK AGC REGISTER S8 FOR A VALUE OF 32 - MOMENTARILY SHORT TP2001 TO TP2002 - CHANGE 'S' WITH CHANNEL & 'D' WITH VOL.
SHARP	27FS120	N/A	DISTORTED PICTURE - NO SYNC	CHECK/REPLACE IC201 (P/N# RH-IX2429CEZZ)
SHARP	27FS120	N/A	SHORT VERTICAL SWEEP AT TOP AND BOTTOM	CHECK/REPLACE IC751 (9 VOLT REGULATOR) (P/N# VHITA7809S/-1)
SHARP	27FS120	N/A	33 VOLT TUNING PIN 'VT' ON TUNER IS SHORTED, USUALLY AFTER AN ELECTRICAL SURGE OR STORM	CHECK/REPLACE TUNER (P/N# VTUVTSH6UZFC/) AND ADD KIT TO PREVENT FROM REOCCURENCE (P/N# BQC-27FS50//1)
SHARP	27FS120	N/A	AUDIO BUZZ WHEN USING AUDIO OUTPUT JACKS THROUGH A STEREO SYSTEM	INSTALL KIT (VRD-RA2BE/KIT) OR REPLACE JUMPER JA402 WITH 82 AND REPLACE C1355 WITH A 330uF @ 16v CAPACITOR
SHARP	27FS150	N/A	DISTORTED PICTURE - NO SYNC	CHECK/REPLACE IC201 (P/N# RH-IX2429CEZZ)
SHARP	27FS150	N/A	SHORT VERTICAL SWEEP AT BOTTOM AND STRETCHED VERTICAL AT THE TOP	CHECK TO MAKE SURE THAT S501 SWITCH IS IN THE DETENT POSITION AND NOT HALF WAY BETWEEN POSITIONS
SHARP	27FS150	N/A	BLANK RASTER - NO SOUND OR PICTURE - OSD WORKS FINE	CHECK AGC REGISTER S8 FOR A VALUE OF 32 - MOMENTARILY SHORT TP2001 TO TP2002 - CHANGE 'S' WITH CHANNEL & 'D' WITH VOL.
SHARP	27FS150	N/A	SHORT VERTICAL SWEEP AT TOP AND BOTTOM	CHECK/REPLACE IC751 (9 VOLT REGULATOR) (P/N# VHITA7809S/-1)
SHARP	27FS200	N/A	BLANK RASTER - NO SOUND OR PICTURE - OSD WORKS FINE	CHECK AGC REGISTER S8 FOR A VALUE OF 32 - MOMENTARILY SHORT TP2001 TO TP2002 - CHANGE 'S' WITH CHANNEL & 'D' WITH VOL.
SHARP	27FS200	N/A	SHORT VERTICAL SWEEP AT BOTTOM AND STRETCHED VERTICAL AT THE TOP	CHECK TO MAKE SURE THAT S501 SWITCH IS IN THE DETENT POSITION AND NOT HALF WAY BETWEEN POSITIONS
SHARP	27FS200	N/A	DISTORTED PICTURE - NO SYNC	CHECK/REPLACE IC201 (P/N# RH-IX2429CEZZ)
SHARP	27FS200	N/A	SHORT VERTICAL SWEEP AT TOP AND BOTTOM	CHECK/REPLACE IC751 (9 VOLT REGULATOR) (P/N# VHITA7809S/-1)
SHARP	27FS300	N/A	DISTORTED PICTURE - NO SYNC	CHECK/REPLACE IC201 (P/N# RH-IX2429CEZZ)
SHARP	27FS300	N/A	SHORT VERTICAL SWEEP AT TOP AND BOTTOM	CHECK/REPLACE IC751 (9 VOLT REGULATOR) (P/N# VHITA7809S/-1)
SHARP	27FS300	N/A	BLANK RASTER - NO SOUND OR PICTURE - OSD WORKS FINE	CHECK AGC REGISTER S8 FOR A VALUE OF 32 - MOMENTARILY SHORT TP2001 TO TP2002 - CHANGE 'S' WITH CHANNEL & 'D' WITH VOL.
SHARP	27FS300	N/A	SHORT VERTICAL SWEEP AT BOTTOM AND STRETCHED VERTICAL AT THE TOP	CHECK TO MAKE SURE THAT S501 SWITCH IS IN THE DETENT POSITION AND NOT HALF WAY BETWEEN POSITIONS
SHARP	27FS40	N/A	DISTORTED PICTURE - NO SYNC	CHECK/REPLACE IC201 (P/N# RH-IX2429CEZZ)
SHARP	27FS40	N/A	33 VOLT TUNING PIN 'VT' ON TUNER IS SHORTED, USUALLY AFTER AN ELECTRICAL SURGE OR STORM	CHECK/REPLACE TUNER (P/N# VTUVTSH6UZFC/) AND ADD KIT TO PREVENT FROM REOCCURENCE (P/N# BQC-27FS50//1)
SHARP	27FS40	N/A	SHORT VERTICAL SWEEP AT TOP AND BOTTOM	CHECK/REPLACE IC751 (9 VOLT REGULATOR) (P/N# VHITA7809S/-1)
SHARP	27FS40	N/A	SHORT VERTICAL SWEEP AT BOTTOM AND STRETCHED VERTICAL AT THE TOP	CHECK TO MAKE SURE THAT S501 SWITCH IS IN THE DETENT POSITION AND NOT HALF WAY BETWEEN POSITIONS
SHARP	27FS40	N/A	BLANK RASTER - NO SOUND OR PICTURE - OSD WORKS FINE	CHECK AGC REGISTER S8 FOR A VALUE OF 32 - MOMENTARILY SHORT TP2001 TO TP2002 - CHANGE 'S' WITH CHANNEL & 'D' WITH VOL.
SHARP	27FS50	N/A	AUDIO BUZZ WHEN USING AUDIO OUTPUT JACKS THROUGH A STEREO SYSTEM	INSTALL KIT (VRD-RA2BE/KIT) OR REPLACE JUMPER JA402 WITH 82 AND REPLACE C1355 WITH A 330uF @ 16v CAPACITOR
SHARP	27FS50	N/A	DISTORTED PICTURE - NO SYNC	CHECK/REPLACE IC201 (P/N# RH-IX2429CEZZ)
SHARP	27FS50	N/A	BLANK RASTER - NO SOUND OR PICTURE - OSD WORKS FINE	CHECK AGC REGISTER S8 FOR A VALUE OF 32 - MOMENTARILY SHORT TP2001 TO TP2002 - CHANGE 'S' WITH CHANNEL & 'D' WITH VOL.
SHARP	27FS50	N/A	33 VOLT TUNING PIN 'VT' ON TUNER IS SHORTED, USUALLY AFTER AN ELECTRICAL SURGE OR STORM	CHECK/REPLACE TUNER (P/N# VTUVTSH6UZFC/) AND ADD KIT TO PREVENT FROM REOCCURENCE (P/N# BQC-27FS50//1)
SHARP	27FS50	N/A	SHORT VERTICAL SWEEP AT TOP AND BOTTOM	CHECK/REPLACE IC751 (9 VOLT REGULATOR) (P/N# VHITA7809S/-1)
SHARP	27FS50	N/A	SHORT VERTICAL SWEEP AT BOTTOM AND STRETCHED VERTICAL AT THE TOP	CHECK TO MAKE SURE THAT S501 SWITCH IS IN THE DETENT POSITION AND NOT HALF WAY BETWEEN POSITIONS
SHARP	27FS6900	N/A	DISTORTED PICTURE - NO SYNC	CHECK/REPLACE IC201 (P/N# RH-IX2429CEZZ)
SHARP	27FS6900	N/A	SHORT VERTICAL SWEEP AT BOTTOM AND STRETCHED VERTICAL AT THE TOP	CHECK TO MAKE SURE THAT S501 SWITCH IS IN THE DETENT POSITION AND NOT HALF WAY BETWEEN POSITIONS
SHARP	27FS6900	N/A	SHORT VERTICAL SWEEP AT TOP AND BOTTOM	CHECK/REPLACE IC751 (9 VOLT REGULATOR) (P/N# VHITA7809S/-1)
SHARP	27GM100	N/A	SHORT VERTICAL SWEEP	CHECK/REPLACE C513 (470uF @ 50v)
SHARP	27GM100	N/A	DEAD - JUST CLICKS	CHECK/REPLACE Q602 (VS2SD1554//1E) AND R717 (VRW-KQ4AC6R8K)
SHARP	27GM120	N/A	SHORT VERTICAL SWEEP	CHECK/REPLACE C513 (470uF @ 50v)
SHARP	27GM120	N/A	DEAD - JUST CLICKS	CHECK/REPLACE Q602 (VS2SD1554//1E) AND R717 (VRW-KQ4AC6R8K)
SHARP	27GM150	N/A	DEAD - JUST CLICKS	CHECK/REPLACE Q602 (VS2SD1554//1E) AND R717 (VRW-KQ4AC6R8K)
SHARP	27GM150	N/A	SHORT VERTICAL SWEEP	CHECK/REPLACE C513 (470uF @ 50v)
SHARP	27GM200	N/A	SHORT VERTICAL SWEEP	CHECK/REPLACE C513 (470uF @ 50v)
SHARP	27GM200	N/A	DEAD - JUST CLICKS	CHECK/REPLACE Q602 (VS2SD1554//1E) AND R717 (VRW-KQ4AC6R8K)
SHARP	27GM60	N/A	DEAD - JUST CLICKS	CHECK/REPLACE Q602 (VS2SD1554//1E) AND R717 (VRW-KQ4AC6R8K)
SHARP	27GM60	N/A	SHORT VERTICAL SWEEP	CHECK/REPLACE C513 (470uF @ 50v)
SHARP	27GM80	N/A	DEAD - JUST CLICKS	CHECK/REPLACE Q602 (VS2SD1554//1E) AND R717 (VRW-KQ4AC6R8K)
SHARP	27GM80	N/A	SHORT VERTICAL SWEEP	CHECK/REPLACE C513 (470uF @ 50v)
SHARP	27GS100	N/A	RED 'T' IN THE UPPER RIGHT CORNER OF SCREEN CAUSE BY PRESSING '4' OF ANOTHER MANUFACTURES REMOTE	BEFORE REPL.IC2001, PRESS '4' KEY ON ORIG. REMOTE TO RESET CHECK/REPLACE IC2001 (P/N# RH-IX2552CEN2 OR RH-IX2599CEN2)
SHARP	27GS100	N/A	DEAD SET	CHECK/REPLACE R706 (150?1/2 watt) (P/N# VRS-RG2HC151)
SHARP	27GS100	N/A	INTERMITTENTLY SHUTS OFF	CHECK/RESOLDER CONNECTIONS ON PIN #9 & #10 OF FLYBACK
SHARP	27GS100	N/A	NO SOUND - PICTURE IS FINE	SHORT TP2001 AND TP2002 - ADVANCE ON-SCREEN REGISTER TO #33, - ADJUST SETTING TO #02 INSTEAD OF #00
SHARP	27GS100	N/A	NO SOUND BUT PICTURE IS OK - SET MAY EXHIBIT AFT PROBLEMS	GO INTO SERVICE MENU BY SHORTING TP2001 & TP2002, USE CHAN. UP TO ADVANCE TO S33, USE VOL UP/DOWN TO SET TO 'BF'
SHARP	27GS120	N/A	RED 'T' IN THE UPPER RIGHT CORNER OF SCREEN CAUSE BY PRESSING '4' OF ANOTHER MANUFACTURES REMOTE	BEFORE REPL.IC2001, PRESS '4' KEY ON ORIG. REMOTE TO RESET CHECK/REPLACE IC2001 (P/N# RH-IX2552CEN2 OR RH-IX2599CEN2)
SHARP	27GS120	N/A	NO SOUND BUT PICTURE IS OK - SET MAY EXHIBIT AFT PROBLEMS	GO INTO SERVICE MENU BY SHORTING TP2001 & TP2002, USE CHAN. UP TO ADVANCE TO S33, USE VOL UP/DOWN TO SET TO 'BF'
SHARP	27GS120	N/A	DEAD SET	CHECK/REPLACE R706 (150?1/2 watt) (P/N# VRS-RG2HC151)
SHARP	27GS120	N/A	NO SOUND - PICTURE IS FINE	SHORT TP2001 AND TP2002 - ADVANCE ON-SCREEN REGISTER TO #33, - ADJUST SETTING TO #02 INSTEAD OF #00
SHARP	27GS120	N/A	INTERMITTENTLY SHUTS OFF	CHECK/RESOLDER CONNECTIONS ON PIN #9 & #10 OF FLYBACK
SHARP	27GS60	N/A	NO SOUND BUT PICTURE IS OK - SET MAY EXHIBIT AFT PROBLEMS	GO INTO SERVICE MENU BY SHORTING TP2001 & TP2002, USE CHAN. UP TO ADVANCE TO S33, USE VOL UP/DOWN TO SET TO '82'
SHARP	27GS60	N/A	INTERMITTENTLY SHUTS OFF	CHECK/RESOLDER CONNECTIONS ON PIN #9 & #10 OF FLYBACK
SHARP	27GS60	N/A	RED 'T' IN THE UPPER RIGHT CORNER OF SCREEN CAUSE BY PRESSING '4' OF ANOTHER MANUFACTURES REMOTE	BEFORE REPL.IC2001, PRESS '4' KEY ON ORIG. REMOTE TO RESET CHECK/REPLACE IC2001 (P/N# RH-IX2552CEN2 OR RH-IX2599CEN2)
SHARP	27GS60	N/A	DEAD SET	CHECK/REPLACE R706 (150?1/2 watt) (P/N# VRS-RG2HC151)
SHARP	27GS60	N/A	NO SOUND - PICTURE IS FINE	SHORT TP2001 AND TP2002 - ADVANCE ON-SCREEN REGISTER TO #33, - ADJUST SETTING TO #02 INSTEAD OF #00
SHARP	27GS80	N/A	INTERMITTENTLY SHUTS OFF	CHECK/RESOLDER CONNECTIONS ON PIN #9 & #10 OF FLYBACK
SHARP	27GS80	N/A	NO SOUND BUT PICTURE IS OK - SET MAY EXHIBIT AFT PROBLEMS	GO INTO SERVICE MENU BY SHORTING TP2001 & TP2002, USE CHAN. UP TO ADVANCE TO S33, USE VOL UP/DOWN TO SET TO '9E'
SHARP	27GS80	N/A	DEAD SET	CHECK/REPLACE R706 (150?1/2 watt) (P/N# VRS-RG2HC151)
SHARP	27GS80	N/A	NO SOUND - PICTURE IS FINE	SHORT TP2001 AND TP2002 - ADVANCE ON-SCREEN REGISTER TO #33, - ADJUST SETTING TO #02 INSTEAD OF #00
SHARP	27GS80	N/A	RED 'T' IN THE UPPER RIGHT CORNER OF SCREEN CAUSE BY PRESSING '4' OF ANOTHER MANUFACTURES REMOTE	BEFORE REPL.IC2001, PRESS '4' KEY ON ORIG. REMOTE TO RESET CHECK/REPLACE IC2001 (P/N# RH-IX2552CEN2 OR RH-IX2599CEN2)
SHARP	27HS60	N/A	NO VERTICAL SWEEP	CHECK/REPLACE IC501 (P/N# VHITA8427K/-1) AND R466 (P/N# VRN-RL3DB1R8J)
SHARP	27HS80	N/A	NO VERTICAL SWEEP	CHECK/REPLACE IC501 (P/N# VHITA8427K/-1) AND R466 (P/N# VRN-RL3DB1R8J)
SHARP	27NL20	N/A	POWER RELAY FAILURE	INSTALL KIT # BQC-27RC399-1
SHARP	27NL30	N/A	POWER RELAY FAILURE	INSTALL KIT # BQC-27RC399-1
SHARP	27NL40	N/A	POWER RELAY FAILURE	INSTALL KIT # BQC-27SV70/-1
SHARP	27RC379	N/A	WON'T SHUT OFF - LOOKS LIKE A STUCK RELAY	CHECK Q1501 FOR SHORTS OR LEAKAGE
SHARP	27RC379	N/A	POWER RELAY FAILURE	INSTALL KIT # BQC-27SV70/-1
SHARP	27RC399	N/A	POWER RELAY FAILURE	INSTALL KIT # BQC-27RC399-1
SHARP	27RC480	N/A	POWER RELAY FAILURE	INSTALL KIT # BQC-27SV70/-1
SHARP	27RC480	N/A	WON'T SHUT OFF - LOOKS LIKE A STUCK RELAY	CHECK Q1501 FOR SHORTS OR LEAKAGE
SHARP	27RV629	N/A	POWER RELAY FAILURE	INSTALL KIT # BQC-27SV70/-1
SHARP	27RV629	N/A	WON'T SHUT OFF - LOOKS LIKE A STUCK RELAY	CHECK Q1501 FOR SHORTS OR LEAKAGE
SHARP	27RV629	27R2	DISTORTED SOUND AND USUALLY THERMAL	CHECK/REPLACE IC201 (TA8680N)
SHARP	27RV649	N/A	POWER RELAY FAILURE	INSTALL KIT # BQC-27SV70/-1
SHARP	27RV649	N/A	WON'T SHUT OFF - LOOKS LIKE A STUCK RELAY	CHECK Q1501 FOR SHORTS OR LEAKAGE
SHARP	27RV649	27R2	DISTORTED SOUND AND USUALLY THERMAL	CHECK/REPLACE IC201 (TA8680N)
SHARP	27RV69	N/A	POWER RELAY FAILURE	INSTALL KIT # BQC-27SV70/-1
SHARP	27RV69	N/A	WON'T SHUT OFF - LOOKS LIKE A STUCK RELAY	CHECK Q1501 FOR SHORTS OR LEAKAGE
SHARP	27RV69	27R2	DISTORTED SOUND AND USUALLY THERMAL	CHECK/REPLACE IC201 (TA8680N)
SHARP	27RV729	N/A	REPEATED FAILURE OF THE HORZ. OUTPUT XSTR.	CHECK/REPLACE Q2601,Q2602
SHARP	27RV729	N/A	POWER RELAY FAILURE	INSTALL KIT # BQC-27SV70/-1
SHARP	27RV729	N/A	WON'T SHUT OFF - LOOKS LIKE A STUCK RELAY	CHECK Q1501 FOR SHORTS OR LEAKAGE
SHARP	27RV729	27R2	DISTORTED SOUND AND USUALLY THERMAL	CHECK/REPLACE IC201 (TA8680N)
SHARP	27RV749	N/A	WON'T SHUT OFF - LOOKS LIKE A STUCK RELAY	CHECK Q1501 FOR SHORTS OR LEAKAGE
SHARP	27RV749	N/A	POWER RELAY FAILURE	INSTALL KIT # BQC-27SV70/-1
SHARP	27RV79	N/A	WON'T SHUT OFF - LOOKS LIKE A STUCK RELAY	CHECK Q1501 FOR SHORTS OR LEAKAGE
SHARP	27RV79	N/A	POWER RELAY FAILURE	INSTALL KIT # BQC-27SV70/-1
SHARP	27RV79	N/A	WHEN CHANNELS ARE CHANGED,SET DISPLAYS VIDEO MODE ON THE OSD AND THIS IS NOT A MONITOR MODEL.	CHECK/REPLACE MICROPROCESSOR IC
SHARP	27RV79	N/A	REPEATED FAILURE OF THE HORZ. OUTPUT XSTR.	CHECK/REPLACE Q2601,Q2602
SHARP	27RV79	27R2	DISTORTED SOUND AND USUALLY THERMAL	CHECK/REPLACE IC201 (TA8680N)
SHARP	27RV99	N/A	POWER RELAY FAILURE	INSTALL KIT # BQC-27RC399-1
SHARP	27SV65	N/A	DEAD SET - RELAY WILL NOT CLICK	CHECK/REPLACE Q1501 AND D2708 FOR SHORT
SHARP	27SV65	N/A	REPEATED FAILURE OF THE HORZ. OUTPUT XSTR.	CHECK/REPLACE Q2601,Q2602
SHARP	27SV65	N/A	WHEN CHANNELS ARE CHANGED,SET DISPLAYS VIDEO MODE ON THE OSD AND THIS IS NOT A MONITOR MODEL.	CHECK/REPLACE MICROPROCESSOR IC
SHARP	27SV65	N/A	WON'T SHUT OFF - LOOKS LIKE A STUCK RELAY	CHECK Q1501 FOR SHORTS OR LEAKAGE
SHARP	27SV65	N/A	POWER RELAY FAILURE	INSTALL KIT # BQC-27SV70/-1
SHARP	27SV65	27R2	DISTORTED SOUND AND USUALLY THERMAL	CHECK/REPLACE IC201 (TA8680N)
SHARP	27SV65B	N/A	POWER RELAY FAILURE	INSTALL KIT # BQC-27SV70/-1
SHARP	27SV70	N/A	POWER RELAY FAILURE	INSTALL KIT # BQC-27SV70/-1
SHARP	27SV729	N/A	POWER RELAY FAILURE	INSTALL KIT # BQC-27SV70/-1
SHARP	27SV79	N/A	POWER RELAY FAILURE	INSTALL KIT # BQC-27SV70/-1
SHARP	FF19663	N/A	INTERMITTENTLY CHANGES ITSELF TO CHANNEL 2	CHECK/CLEAN/REPLACE THE CATV/AIR SWITCH
SHARP	FF19663	N/A	SMEARY PIX AFTER FLYBACK REPL.--LOOKS LIKE CRT	CHECK R423 (10k) FOR OPEN
SHARP	FF19663	N/A	PIX TOO BRIGHT AND SCREEN CONTROL HAS NO AFFECT	CHECK/REPLACE D401
SHARP	FF19663	N/A	NO SOUND NO PIX.	CHECK/REPLACE R621,D601,R423 & H.O.T.
SHARP	FF19663	N/A	SHORT ON 18 VOLT SCAN SUPPLY	CHECK IC701 FOR SHORT
SHARP	FF19663	N/A	DEAD,SLOW TICKING,NO COLL. B+ TO HORZ. OUT	CHECK FOR OPEN FLYBACK WINDING
SHARP	FF19663	N/A	VERT JITTER OR ROLL WHEN COLD	C504,C510
SHARP	FF19663	N/A	VERTICAL FOLD OVER AT BOTTOM OF PIX	CHECK/REPLACE C510
SHARP	FF19663	N/A	VERTICAL JITTER	C510
SHARP	FF19663	N/A	VERTICAL OUTPUT PROMBLEMS	CHECK D503,R522,C504.C510
SHARP	FF19663	N/A	SLOW TICKING	IC801,R619
SHARP	FF19663	N/A	GASSY PIX--LOOKS LIKE CRT IS BAD	CHECK FOR LEAKY C856
SHARP	FF19663	N/A	NO COLOR;VERT SHADING BARS ON LEFT SIDE OF PIX	CHECK R425
SHARP	FF19663	N/A	NO COLOR	IC801
SHARP	FF19663	N/A	NO B/W PIX.	CHECK/REPLACE R422,R423
SHARP	FF19663	N/A	WHITE RASTER NO VIDEO OR SOUND	CHECK C220 FOR SHORTED CONDITION
SHARP	FF19663	N/A	SET WILL NOT START UP	R611
SHARP	FF19663	N/A	JAIL BARS ON SCREEN ALSO LACK OF COLOR	CHECK R425 (12k) FOR OPEN
SHARP	FF19663	N/A	NO VIDEO	R423 OPEN USUALLY AFTER FLYBACK GOES OUT
SHARP	FF19663	N/A	INTERMITTENT VERTICAL ROLL PIX ROLLS FIRSTFEW MI	CHECK / REPLACE C504 C510-470 UF50WV
SHARP	FF19663	N/A	SOUND AND CHROMA OK - NO VIDEO INFORMATION	CHECK/REPLACE R422 (100k) FOR OPEN
SHARP	FF19663	N/A	FUSE BLOWING	Q602,D701-D704
SHARP	FF19663	N/A	NO COLOR BUT MAY HAVE VERY WEAK COLOR BARS	CHECK/REPLACE C809 (TRIMMER CAPACITOR FOR 3.58MHz ADJUST)
SHARP	FF19663	N/A	NO PICTURE - HAS HV AND SOUND IS NORMAL	CHECK/REPLACE R422 (100k)
SHARP	FF19663	N/A	NO RASTER	CHECK/REPLACE C855,C856
SHARP	FF19663	N/A	NO SOUND NO PICTURE	IC801,R705
SHARP	FF19663	N/A	GASSY PIX-LOOKS LIKE CRT IS BAD	CHECK C856 FOR LEAKAGE--CHECKS OK FOR VALUE
SHARP	FF19663	N/A	SHORT VERT SWEEP	C506
SHARP	FF19663	N/A	BLACK BAR 1'TO 2' FROM BOTTOM OF PIX	CHECK/REPLACE C510
SHARP	FF19663	N/A	NO SOUND AND NO PIX - MAY POSSIBLY TICK	CHECK Q602 FOR LEAKY/SHORT AND R613 FOR OPEN
SHARP	FF19663	N/A	RAPIDLY PULSATES ON/OFF WHEN SET IS 1ST PLUG IN	CHECK THE SCR FOR LEAKY GATE
SHARP	FF19663	N/A	WHITE SHADING BAR ON RIGHT SIDE	DRESS LEADS AWAY FROM YOKE AND FLYBACK
SHARP	FF19663	N/A	DARK PICTURE AFTER CHANGING FLYBACK	CHECK OR REPLACE Q401,Q402,R423,C407
SHARP	FF19663	N/A	FAST TICKING	R715,D705
SHARP	XM2001	N/A	POWER RELAY FAILURE	INSTALL KIT # BQC-20RV99/-1
SHARP	XM2701	N/A	POWER RELAY FAILURE	INSTALL KIT # BQC-27SV70/-1
SONY	CCDV99	N/A	UNIT CUES AND REVIEWS AT THE LP SPEED	CHECK/REPLACE C833
SONY	CKV27DST1	N/A	WON'T STORE THE SERVICE SETTINGS	CHECK/REPLACE IC102 (8-759-251-04)
SONY	CKV27DST1	N/A	DEAD SET - MISSING 5 VOLT STANDBY VOLTAGE	CHECK/REPLACE IC602 (P/N# 8-759-805-37), R636 (1.5?- P/N# 1-249-383-11) AND D638 (P/N# 8-719-911-19)
SONY	CKV27HX1	N/A	WON'T STORE THE SERVICE SETTINGS	CHECK/REPLACE IC102 (8-759-251-04)
SONY	CKV27HX1	N/A	DEAD SET - MISSING 5 VOLT STANDBY VOLTAGE	CHECK/REPLACE IC602 (P/N# 8-759-805-37), R636 (1.5?- P/N# 1-249-383-11) AND D638 (P/N# 8-719-911-19)
SONY	CPD15SF1	N/A	RED SCREEN WITH RETRACE LINES	CHECK/REPLACE R118
SONY	FD10A	N/A	LOW AUDIO BUZZING SOUND	CHECK/REPLACE RV451
SONY	FD500	N/A	INTERMITTENT LINES IN PICTURE	CHECK/RESOLDER CONNECTIONS ON T801 (PIN#5)
SONY	FD510	N/A	RETRACE LINES IN PICTURE AND G1 VOLTAGE HIGH	CHECK/REPLACE CRT
SONY	FD555	N/A	INTERMITTENT PICTURE AND BRIGHTNESS	CHECK/RESOLDER CONNECTIONS ON C807
SONY	FDC290	N/A	CAN NOT SET CLOCK - TV WORKS FINE	CHECK/RESOLDER CONNECTIONS ON CN703
SONY	GDM20SE1	N/A	PICTURE JITTERS HORZ.	CHECK/RESOLDER CONNECTIONS ON CN910 PIN# 11 ON 'N' BOARD
SONY	GDM20SE1	N/A	UNIT SHUTS DOWN	CHECK/REPLACE D824 SHORTED AND PS500 OPEN
SONY	KP41EXR96	N/A	INTERMITTENT CLOSED CAPTION CHARACTER ERROR IN WEAK SIGNAL CONDITIONS - MAY SHOW A WHITE CHARACTER OR BLACK BOX	CHANGE VALUE OF R3443 FROM 470 TO A 100 (P/N# 1-216-025-00)
SONY	KP46V15	N/A	INTERMITTENT CLOSED CAPTION CHARACTER ERROR IN WEAK SIGNAL CONDITIONS - MAY SHOW A WHITE CHARACTER OR BLACK BOX	CHANGE VALUE OF R3443 FROM 470 TO A 100 (P/N# 1-216-025-00)
SONY	KP46V16	N/A	INTERMITTENT CLOSED CAPTION CHARACTER ERROR IN WEAK SIGNAL CONDITIONS - MAY SHOW A WHITE CHARACTER OR BLACK BOX	CHANGE VALUE OF R3443 FROM 470 TO A 100 (P/N# 1-216-025-00)
SONY	KP46XBR25	N/A	INTERMITTENT CLOSED CAPTION CHARACTER ERROR IN WEAK SIGNAL CONDITIONS - MAY SHOW A WHITE CHARACTER OR BLACK BOX	CHANGE VALUE OF R3443 FROM 470 TO A 100 (P/N# 1-216-025-00)
SONY	KP53V15	N/A	INTERMITTENT CLOSED CAPTION CHARACTER ERROR IN WEAK SIGNAL CONDITIONS - MAY SHOW A WHITE CHARACTER OR BLACK BOX	CHANGE VALUE OF R3443 FROM 470 TO A 100 (P/N# 1-216-025-00)
SONY	KP53V16	N/A	INTERMITTENT CLOSED CAPTION CHARACTER ERROR IN WEAK SIGNAL CONDITIONS - MAY SHOW A WHITE CHARACTER OR BLACK BOX	CHANGE VALUE OF R3443 FROM 470 TO A 100 (P/N# 1-216-025-00)
SONY	KP53XBR25	N/A	INTERMITTENT CLOSED CAPTION CHARACTER ERROR IN WEAK SIGNAL CONDITIONS - MAY SHOW A WHITE CHARACTER OR BLACK BOX	CHANGE VALUE OF R3443 FROM 470 TO A 100 (P/N# 1-216-025-00)
SONY	KP61V15	N/A	INTERMITTENT CLOSED CAPTION CHARACTER ERROR IN WEAK SIGNAL CONDITIONS - MAY SHOW A WHITE CHARACTER OR BLACK BOX	CHANGE VALUE OF R3443 FROM 470 TO A 100 (P/N# 1-216-025-00)
SONY	KP61XBR28	N/A	INTERMITTENT CLOSED CAPTION CHARACTER ERROR IN WEAK SIGNAL CONDITIONS - MAY SHOW A WHITE CHARACTER OR BLACK BOX	CHANGE VALUE OF R3443 FROM 470 TO A 100 (P/N# 1-216-025-00)
SONY	KPR41EXR95	N/A	STANDBY POWER SUPPLY DEAD	CHECK/REPLACE Q624,R669,R686,R675,IC606 - CHANGE C636 TO (P/N 1-136-121-00) AND CHANGE D639 TO (P/N 8-719-979-60)
SONY	KPR46EXR15	N/A	STANDBY POWER SUPPLY DEAD	CHECK/REPLACE Q624,R669,R686,R675,IC606 - CHANGE C636 TO (P/N 1-136-121-00) AND CHANGE D639 TO (P/N 8-719-979-60)
SONY	KPR46XBR15	N/A	STANDBY POWER SUPPLY DEAD	CHECK/REPLACE Q624,R669,R686,R675,IC606 - CHANGE C636 TO (P/N 1-136-121-00) AND CHANGE D639 TO (P/N 8-719-979-60)
SONY	KPR46XBR15	N/A	INTERMITTENT VOLUME IN THE SURROUND SOUND MODE	CHECK/REPLACE X-3 BOARD (P/N# A-1394-367-A)
SONY	KPR46XBR15	N/A	INTERMITTENT PICTURE BLANKING ON THE LEFT SIDE OF SCREEN	ADD A SHORT JUMPER FROM 18v SIDE OF R240 TO PIN 4 OF PLUG A-6
SONY	KPR53XBR15	N/A	INTERMITTENT PICTURE BLANKING ON THE LEFT SIDE OF SCREEN	ADD A SHORT JUMPER FROM 18v SIDE OF R240 TO PIN 4 OF PLUG A-6
SONY	KPR53XBR15	N/A	INTERMITTENT VOLUME IN THE SURROUND SOUND MODE	CHECK/REPLACE X-3 BOARD (P/N# A-1394-367-A)
SONY	KPR53XBR15	N/A	STANDBY POWER SUPPLY DEAD	CHECK/REPLACE Q624,R669,R686,R675,IC606 - CHANGE C636 TO (P/N 1-136-121-00) AND CHANGE D639 TO (P/N 8-719-979-60)
SONY	KV10FMR20	N/A	NO PICTURE BUT HAS SOUND	CHECK/REPLACE R835
SONY	KV10FMR20	N/A	SHUTS DOWN	CHECK/REPLACE FLYBACK TRANSFORMER
SONY	KV1326R	N/A	SCREEN GOES WHITE INTERMITTENTLY - GOES TO SNOWY PICTURE	CHECK/RESOLDER CONNECTIONS ON 'IF' TRANSFORMERS INSIDE 'IF BLOCK' ASSY.
SONY	KV1367	N/A	SCREEN GOES WHITE INTERMITTENTLY - GOES TO SNOWY PICTURE	CHECK/RESOLDER CONNECTIONS ON 'IF' TRANSFORMERS INSIDE 'IF BLOCK' ASSY.
SONY	KV1370R	N/A	NO SOUND	CHECK/REPLACE R255
SONY	KV1370R	N/A	NO SOUND	CHECK/REPLACE Q251,Q252 AND R255
SONY	KV1380R	N/A	VERTICAL ROLL	CHECK/REPLACE C230
SONY	KV1392	N/A	INTERMITTENT LOSS OF PICTURE AND SOUND AND SET GOES TO A WHITE RASTER	CHECK/REPLACE IF BLOCK (1-464-478-11) OR RESOLDER COLD SOLDER CONNECTIONS INSIDE ESPECIALLY ON 2 IF COILS
SONY	KV1392R	N/A	HORZ. TEARING LINES IN THE PICTURE	CHECK/REPLACE 'IF' BLOCK ASSY.
SONY	KV1393R	N/A	INTERMITTENT LOSS OF PICTURE AND SOUND - ONLY HAS A WHITE RASTER WHEN SET IS OUT	CHECK/REPLACE IF BLOCK (1-464-478-11)
SONY	KV1397	SCC648CA	NO SOUND	CHECK Q251,Q252,R255
SONY	KV1397R	N/A	HORZ. TEARING LINES IN THE PICTURE	CHECK/REPLACE 'IF' BLOCK ASSY.
SONY	KV13EXR90	N/A	INTERMITTENT PICTURE OR SNOW	CHECK/RESOLDER CONNECTIONS IN TUNER WHERE CASING IS SOLDERED TO PCB NEAR 4TH FEED THRU BACK FROM ANTENNA INPUT
SONY	KV13EXR90	N/A	AUDIO BUZZ FROM THE SPEAKERS	ADD WIRE BETWEEN A001 AND A004 AND BETWEEN A004 AND A003
SONY	KV13EXR91	N/A	HUM FROM SPEAKER AT LOW OR NO VOLUME	ADD A WIRE FROM A001 TO A004 AND ALSO A004 AND A003 ON THE 'A' BOARD
SONY	KV13EXR91	N/A	INTERMITTENT PICTURE OR SNOW	CHECK/RESOLDER CONNECTIONS IN TUNER WHERE CASING IS SOLDERED TO PCB NEAR 4TH FEED THRU BACK FROM ANTENNA INPUT
SONY	KV13M10	N/A	SET SHUTS DOWN INTERMITTENTLY	ENTER SERVICE MODE AND SELECT 'SHAP' AND CHANGE DATE FROM 7 TO 5 -IF THIS FAILS,THEN CHANGE IC301 (P/N# 8-752-069-09)
SONY	KV13TR10	N/A	INTERMITTENT LOSS OF PICTURE AND SOUND AND SET GOES TO A WHITE RASTER	CHECK/REPLACE IF BLOCK (1-464-478-11) OR RESOLDER COLD SOLDER CONNECTIONS INSIDE ESPECIALLY ON 2 IF COILS
SONY	KV13TR20	N/A	INTERMITTENT LOSS OF PICTURE AND SOUND AND SET GOES TO A WHITE RASTER	CHECK/REPLACE IF BLOCK (1-464-478-11) OR RESOLDER COLD SOLDER CONNECTIONS INSIDE ESPECIALLY ON 2 IF COILS
SONY	KV13TR21	N/A	SET LOSES AUDIO AND VIDEO INTERMITTENTLY - GOES TO WHITE SCREEN	CHECK/RESOLDER CONNECTIONS IN 'IF BLOCK' ON (3) IF XFRMS.
SONY	KV13TR24	N/A	INTERMITTENT PICTURE OR SNOW	CHECK/RESOLDER CONNECTIONS IN TUNER WHERE CASING IS SOLDERED TO PCB NEAR 4TH FEED THRU BACK FROM ANTENNA INPUT
SONY	KV13TR24	N/A	SNOWY PICTURE	CHECK/REPLACE TUNER
SONY	KV13TR28	N/A	POWER SUPPLY IMPROVEMENT - REDUCE AC SPARK WHEN SET IS PLUGGED IN	CHECK/REPLACE REMOVE JUMPERS AT JW603,JW604 AND REPLACE WITH 2.2 RESISTOR (P/N# 1-208-294-11)
SONY	KV13TR28	N/A	ROUND CIRCLE OF RED AND BLUE IN THE MIDDLE OF SCREEN WITH TV TURNED OFF.	CHECK/RESOLDER CONNECTIONS ON GROUND WIRE FROM 'C' BOARD TO CRT BOARD
SONY	KV13TR28	N/A	VERTICAL ROLL	CHECK/REPLACE C322
SONY	KV13TR28	N/A	SET SHUTS DOWN INTERMITTENTLY	ENTER SERVICE MODE AND SELECT 'SHAP' AND CHANGE DATE FROM 7 TO 5 -IF THIS FAILS,THEN CHANGE IC301 (P/N# 8-752-069-09)
SONY	KV13TR29	N/A	POWER SUPPLY IMPROVEMENT - REDUCE AC SPARK WHEN SET IS PLUGGED IN	CHECK/REPLACE REMOVE JUMPERS AT JW603,JW604 AND REPLACE WITH 2.2 RESISTOR (P/N# 1-208-294-11)
SONY	KV13TR29	N/A	SET SHUTS DOWN INTERMITTENTLY	ENTER SERVICE MODE AND SELECT 'SHAP' AND CHANGE DATE FROM 7 TO 5 -IF THIS FAILS,THEN CHANGE IC301 (P/N# 8-752-069-09)
SONY	KV13TR29	N/A	NO PICTURE AFTER A FEW MINUTES	CHECK/REPLACE Q631
SONY	KV13V50	N/A	POWER SUPPLY IMPROVEMENT - REDUCE AC SPARK WHEN SET IS PLUGGED IN	CHECK/REPLACE REMOVE JUMPERS AT JW603,JW604 AND REPLACE WITH 2.2 RESISTOR (P/N# 1-208-294-11)
SONY	KV13VM20	N/A	UNIT TICKS AND THEN SHUTSDOWN	CHECK/REPLACE Q1801 2SD1135-C (P/N# 8-729-301-42)
SONY	KV13VM20	N/A	CASSETTE WON'T LOAD - LOW AUDIO	CHECK/REPLACE FR1805 (0.68?@ 2w) RESISTOR
SONY	KV13VM20	N/A	DEAD SET	CHECK/REPLACE IC801
SONY	KV13VM21	N/A	UNIT TICKS AND THEN SHUTSDOWN	CHECK/REPLACE Q1801 2SD1135-C (P/N# 8-729-301-42)
SONY	KV1403R	N/A	INTERMITTENT LOSS OF PICTURE AND SOUND AND SET GOES TO A WHITE RASTER	CHECK/REPLACE IF BLOCK (1-464-478-11) OR RESOLDER COLD SOLDER CONNECTIONS INSIDE ESPECIALLY ON 2 IF COILS
SONY	KV1483RWP	N/A	INTERMITTENT LOSS OF PICTURE AND SOUND AND SET GOES TO A WHITE RASTER	CHECK/REPLACE IF BLOCK (1-464-478-11) OR RESOLDER COLD SOLDER CONNECTIONS INSIDE ESPECIALLY ON 2 IF COILS
SONY	KV1515	SCC350AA	WILL NOT TUNE ABOVE CHANNEL 3	CHECK Q101 FOR E-B SHORT
SONY	KV18R186WB	N/A	INTERMITTENT LOSS OF PICTURE AND SOUND AND SET GOES TO A WHITE RASTER	CHECK/REPLACE IF BLOCK (1-464-478-11) OR RESOLDER COLD SOLDER CONNECTIONS INSIDE ESPECIALLY ON 2 IF COILS
SONY	KV1914	N/A	HORIZONTAL LINES ACROSS TOP OF PICTURE	CHECK/REPLACE C529
SONY	KV1923	N/A	SHORT VERTICAL SWEEP - NARROW HORZ. ALSO	CHECK/RESOLDER CONNECTIONS ON L508
SONY	KV1928R	N/A	DEAD SET	CHECK/REPLACE D604 AND R613
SONY	KV1946	N/A	DEAD-NO 12V STANDBY VOLTAGE	CHECK R123 AND D007
SONY	KV1947RX	N/A	INTERMITTENT SHUTDOWN AFTER 1-2 HOURS	CHECK/REPLACE HVR STAT CONTROL
SONY	KV1952	N/A	RETRACE LINES AT TOP OF SCREEN	CHECK/REPLACE C531, C532 AND C534
SONY	KV1952	N/A	BRIGHT PIX W/RETRACE LINES	CHECK/REPLACE R721 FOR OPEN (680k)
SONY	KV1953	N/A	BRIGHT PIX W/RETRACE LINES	CHECK/REPLACE R721 FOR OPEN (680k)
SONY	KV1957R	N/A	INTERMITTENT SOUND OR RASPY SOUND	CHECK/REPLACE IC601
SONY	KV1957R	N/A	INTERMITTENTLY SHUTSDOWN	CHECK/REPLACE IC601
SONY	KV1957R	N/A	RETRACE LINES AT THE TOP OF SCREEN	CHECK/REPLACE C515 AND C532
SONY	KV19TR10	N/A	INTERMITTENT PICTURE OR SNOW	CHECK/RESOLDER CONNECTIONS IN TUNER WHERE CASING IS SOLDERED TO PCB NEAR 4TH FEED THRU BACK FROM ANTENNA INPUT
SONY	KV19TR20	N/A	BLACK LINES IN THE PICTURE	CHECK/REPLACE TUNER ASSEMBLY
SONY	KV19TR20	N/A	INTERMITTENT PICTURE OR SNOW	CHECK/RESOLDER CONNECTIONS IN TUNER WHERE CASING IS SOLDERED TO PCB NEAR 4TH FEED THRU BACK FROM ANTENNA INPUT
SONY	KV19TR20	N/A	INTERMITTENT NO RECEPTION - SNOW ONLY - WIGGLING COAX CONNECTOR ON REAR OF SET WILL RESTORE TEMPORARILY	CHECK/RESOLDER ALL FEED THRU CONNECTIONS INSIDE TUNER OR REPLACE TUNER (P/N# 1-465-371-11)
SONY	KV19TR20	N/A	UNIT SHUTS DOWN AFTER 30 SECONDS OF OPERATION	CHECK/REPLACE R568 FOR A CHANGE IN VALUE
SONY	KV19TS10	N/A	INTERMITTENT SHUTDOWN	CHECK/REPLACE R561 (P/N# 1-249-496-11)
SONY	KV19TS10	N/A	INTERMITTENT PICTURE OR SNOW	CHECK/RESOLDER CONNECTIONS IN TUNER WHERE CASING IS SOLDERED TO PCB NEAR 4TH FEED THRU BACK FROM ANTENNA INPUT
SONY	KV19TS20	N/A	AUTO PROGRAMMING NOT WORKING	READJUST THE AGC FOR PROPER LEVEL
SONY	KV19TS20	N/A	NO SOUND OR PICTURE BUT DOES HAVE OSD	CHECK/REPLACE IC301
SONY	KV19TS20	N/A	INTERMITTENT PICTURE OR SNOW	CHECK/RESOLDER CONNECTIONS IN TUNER WHERE CASING IS SOLDERED TO PCB NEAR 4TH FEED THRU BACK FROM ANTENNA INPUT
SONY	KV19TS20	N/A	INTERMITTENT SHUTDOWN WHEN BRIGHTNESS WAS CHANGED OR SCENE CHANGES	CHECK/REPLACE R568 (P/N# 1-216-390-15)
SONY	KV2084R	N/A	UNIT COMES ON THEN SHUTS DOWN	CHECK/REPLACE IC103
SONY	KV2084R	N/A	BRIGHT SCENES OVER DRIVEN	CHECK/REPLACE L922
SONY	KV20EXR10	N/A	DEAD SET WITH A BUZZ COMING FROM POWER SUPPLY	CHECK/REPLACE D625 (P/N# ECG588 OR 8-719-948-59)
SONY	KV20EXR10	N/A	RED RETRACE LINES APPEAR ON SCREEN ( SOMETIMES BLUE/GREEN)	CHECK/REPLACE IC701 (P/N# 8-759-980-59) ON THE 'C' BOARD
SONY	KV20EXR10	N/A	CLOCK RUNS TOO FAST	ADD 0.1uF TO BASE OF Q108 TO GROUND (P/N# 1-124-463-00)
SONY	KV20EXR10	N/A	INTERMITTENT LOSS OF VIDEO OR LUMINANCE	CHECK/REPLACE C305 (P/N# 1-124-791-11 OR 1-126-772-11)
SONY	KV20EXR10	N/A	CLOCK RUNS TOO FAST	CHANGE C125 TO A 0.1uF @ 50v CAPACITOR (P/N# 1-124-463-00)
SONY	KV20EXR20	N/A	NO AUDIO	CHECK/RESOLDER CONNECTIONS ON A24 PLUG
SONY	KV20EXR20	N/A	MECHANICAL BUZZ OR HUM AT 60Hz	CHECK/REPLACE T602 (P/N# 1-424-205-21) OR SILICONE ITS SHIELD IN PLACE
SONY	KV20EXR20	N/A	NO VIDEO - SOUND OK - NO FILAMENT	CHECK/REPLACE CRT SOCKET
SONY	KV20EXR20	N/A	DEAD SET WITH A BUZZ COMING FROM POWER SUPPLY	CHECK/REPLACE D625 (P/N# ECG588 OR 8-719-948-59)
SONY	KV20EXR20	N/A	NO PICTURE BUT SOUND OK	CHECK/REPLACE R702
SONY	KV20EXR20	N/A	CLOCK RUNS TOO FAST	ADD 0.1uF TO BASE OF Q108 TO GROUND (P/N# 1-124-463-00)
SONY	KV20EXR20	N/A	HIGH PITCHED SOUND WHICH GETS LOUDER AFTER 1-2 HOURS OF OPERATION	CHECK/REPLACE C507 (P/N# 1-136-904-11)
SONY	KV20M10	N/A	INTERMITTENT OR IMMEDIATE SHUTDOWN	CHECK/REPLACE C517
SONY	KV20M10	N/A	IMPROVEMENT OF POWER SUPPLY CIRCUIT	REPLACE JUMPERS LOCATED AT R603 WITH A 1 @ 10w RESISTOR (P/N# 1-205-998-11)
SONY	KV20M10	N/A	AFTER GLOW PROBLEM	THIS IS NORMAL BUT IF CUSTOMER WILL NOT ACCEPT THAT, THEN INSTALL KIT (P/N# T-9985-6731)
SONY	KV20M10	N/A	UNSTABLE PICTURE - NO PICTURE - POOR FOCUS OR BRIGHTNESS CHANGE	MARK ORIGINAL POSITIONS OF SCREEN AND FOCUS CONTROLS,TURN SCREEN TO MIN./FOCUS TO MAX.-ARCING MAY OCCUR - RESET CTRLS
SONY	KV20M10	N/A	SET SHUTS DOWN INTERMITTENTLY	ENTER SERVICE MODE AND SELECT 'SHAP' AND CHANGE DATE FROM 7 TO 5 -IF THIS FAILS,THEN CHANGE IC301 (P/N# 8-752-069-09)
SONY	KV20RA1	N/A	INTERMITTENT LOSS OF PICTURE AND SOUND AND SET GOES TO A WHITE RASTER	CHECK/REPLACE IF BLOCK (1-464-478-11) OR RESOLDER COLD SOLDER CONNECTIONS INSIDE ESPECIALLY ON 2 IF COILS
SONY	KV20S10	N/A	INTERMITTENTLY GOES TO SNOW OR LOOSES CHANNELS	CHECK/RESOLDER CONNECTIONS INSIDE TUNER WHERE THE CIRCUIT BOARD CONNECTS TO OUTER METAL FRAME
SONY	KV20S10	N/A	AFTER GLOW PROBLEM	THIS IS NORMAL BUT IF CUSTOMER WILL NOT ACCEPT THAT, THEN INSTALL KIT (P/N# T-9985-6731)
SONY	KV20S10	N/A	IMPROVEMENT OF POWER SUPPLY CIRCUIT	REPLACE JUMPERS LOCATED AT R603 WITH A 1 @ 10w RESISTOR (P/N# 1-205-998-11)
SONY	KV20S10	N/A	UNSTABLE PICTURE - NO PICTURE - POOR FOCUS OR BRIGHTNESS CHANGE	MARK ORIGINAL POSITIONS OF SCREEN AND FOCUS CONTROLS,TURN SCREEN TO MIN./FOCUS TO MAX.-ARCING MAY OCCUR - RESET CTRLS
SONY	KV20S10	N/A	SET SHUTS DOWN INTERMITTENTLY	ENTER SERVICE MODE AND SELECT 'SHAP' AND CHANGE DATE FROM 7 TO 5 -IF THIS FAILS,THEN CHANGE IC301 (P/N# 8-752-069-09)
SONY	KV20S11	N/A	AFTER GLOW PROBLEM	THIS IS NORMAL BUT IF CUSTOMER WILL NOT ACCEPT THAT, THEN INSTALL KIT (P/N# T-9985-6731)
SONY	KV20S11	N/A	IMPROVEMENT OF POWER SUPPLY CIRCUIT	REPLACE JUMPERS LOCATED AT R603 WITH A 1 @ 10w RESISTOR (P/N# 1-205-998-11)
SONY	KV20S11	N/A	UNSTABLE PICTURE - NO PICTURE - POOR FOCUS OR BRIGHTNESS CHANGE	MARK ORIGINAL POSITIONS OF SCREEN AND FOCUS CONTROLS,TURN SCREEN TO MIN./FOCUS TO MAX.-ARCING MAY OCCUR - RESET CTRLS
SONY	KV20S11	N/A	SET SHUTS DOWN INTERMITTENTLY	ENTER SERVICE MODE AND SELECT 'SHAP' AND CHANGE DATE FROM 7 TO 5 -IF THIS FAILS,THEN CHANGE IC301 (P/N# 8-752-069-09)
SONY	KV20S20	N/A	NO AUDIO AFTER CHANNEL IS CHANGED - AUDI MUTES	CHECK FOR PRESENCE OF R041 - IF IT EXISTS, REMOVE IT
SONY	KV20S20	N/A
SONY	KV20TR10	N/A	CLOCK RUNS TOO FAST	ADD 0.1uF TO BASE OF Q103 TO GROUND (P/N# 1-124-463-00)
SONY	KV20TR11	N/A	CLOCK RUNS TOO FAST	ADD 0.1uF TO BASE OF Q103 TO GROUND (P/N# 1-124-463-00)
SONY	KV20TR12	N/A	CLOCK RUNS TOO FAST	ADD 0.1uF TO BASE OF Q103 TO GROUND (P/N# 1-124-463-00)
SONY	KV20TR21	N/A	CLOCK RUNS TOO FAST	ADD 0.1uF TO BASE OF Q103 TO GROUND (P/N# 1-124-463-00)
SONY	KV20TR22	N/A	CLOCK RUNS TOO FAST	ADD 0.1uF IN PARALLEL WITH D104 (P/N# 1-124-463-00)
SONY	KV20TR22	N/A	INTERMITTENT PICTURE OR SNOW	CHECK/RESOLDER CONNECTIONS IN TUNER WHERE CASING IS SOLDERED TO PCB NEAR 4TH FEED THRU BACK FROM ANTENNA INPUT
SONY	KV20TR23	N/A	INTERMITTENT PINCUSHION BOW	CHECK/REPLACE R533
SONY	KV20TR23	N/A	POWER SUPPLY IMPROVEMENT - REDUCE AC SPARK WHEN SET IS PLUGGED IN	CHECK/REPLACE REMOVE JUMPERS AT JW603,JW604 AND REPLACE WITH 2.2 RESISTOR (P/N# 1-208-294-11)
SONY	KV20TS10	N/A	CLOCK RUNS TOO FAST	ADD 0.1uF TO BASE OF Q103 TO GROUND (P/N# 1-124-463-00)
SONY	KV20TS11	N/A	CLOCK RUNS TOO FAST	ADD 0.1uF TO BASE OF Q103 TO GROUND (P/N# 1-124-463-00)
SONY	KV20TS12	N/A	CLOCK RUNS TOO FAST	ADD 0.1uF TO BASE OF Q103 TO GROUND (P/N# 1-124-463-00)
SONY	KV20TS13	N/A	CLOCK RUNS TOO FAST	ADD 0.1uF TO BASE OF Q103 TO GROUND (P/N# 1-124-463-00)
SONY	KV20TS20	N/A	BUZZING SOUND AND SET WOULD SHUTDOWN	CHECK/REPLACE IC601
SONY	KV20TS20	N/A	INTERMITTENT LINES IN PICTURE	CHECK/RESOLDER CONNECTIONS IN 'IF' PACK ON TRANSFORMERS
SONY	KV20TS20	N/A	CLOCK RUNS TOO FAST	ADD 0.1uF TO BASE OF Q103 TO GROUND (P/N# 1-124-463-00)
SONY	KV20TS20	N/A	NO SOUND OR PICTURE BUT DOES HAVE OSD	CHECK/REPLACE IC301
SONY	KV20TS21	N/A	CLOCK RUNS TOO FAST	ADD 0.1uF TO BASE OF Q103 TO GROUND (P/N# 1-124-463-00)
SONY	KV20TS22	N/A	CLOCK RUNS TOO FAST	ADD 0.1uF TO BASE OF Q103 TO GROUND (P/N# 1-124-463-00)
SONY	KV20TS23	N/A	CLOCK RUNS TOO FAST	ADD 0.1uF TO BASE OF Q103 TO GROUND (P/N# 1-124-463-00)
SONY	KV20TS23	N/A	DEAD SET	CHECK/REPLACE RELAY,C605 AND D602
SONY	KV20TS24	N/A	CLOCK RUNS TOO FAST	ADD 0.1uF TO BASE OF Q103 TO GROUND (P/N# 1-124-463-00)
SONY	KV20TS27	N/A	CLOCK RUNS TOO FAST	ADD 0.1uF IN PARALLEL WITH D104 (P/N# 1-124-463-00)
SONY	KV20TS27	N/A	NO SOUND	CHECK/REPLACE IC101 (P/N# 8-759-636-45)
SONY	KV20TS27	N/A	INTERMITTENT PICTURE OR SNOW	CHECK/RESOLDER CONNECTIONS IN TUNER WHERE CASING IS SOLDERED TO PCB NEAR 4TH FEED THRU BACK FROM ANTENNA INPUT
SONY	KV20TS27	N/A	NO POWER - DEAD SET	CHECK/REPLACE D605 FOR SHORT
SONY	KV20TS27	N/A	BLACK LINES IN THE PICTURE	CHECK/REPLACE TUNER ASSEMBLY
SONY	KV20TS28	N/A	CLOCK RUNS TOO FAST	ADD 0.1uF IN PARALLEL WITH D104 (P/N# 1-124-463-00)
SONY	KV20TS28	N/A	INTERMITTENT PICTURE OR SNOW	CHECK/RESOLDER CONNECTIONS IN TUNER WHERE CASING IS SOLDERED TO PCB NEAR 4TH FEED THRU BACK FROM ANTENNA INPUT
SONY	KV20TS29	N/A	CHANNELS CHANGE BY THEMSELVES AND LOCK UP	CHECK/REPLACE X001
SONY	KV20TS29	N/A	POWER SUPPLY IMPROVEMENT - REDUCE AC SPARK WHEN SET IS PLUGGED IN	CHECK/REPLACE REMOVE JUMPERS AT JW603,JW604 AND REPLACE WITH 2.2 RESISTOR (P/N# 1-208-294-11)
SONY	KV20TS30	N/A	COLOR IS BAD	CHECK/RESOLDER CONNECTIONS ON TH-601
SONY	KV20TS30	N/A	CLOCK RUNS TOO FAST	ADD 0.1uF TO BASE OF Q103 TO GROUND (P/N# 1-124-463-00)
SONY	KV20TS32	N/A	'AFTER GLOW' OF CRT AFTER SET IS SHUT OFF	CHECK/REPLACE IC101 (P/N# 8-752-856-00) ALSO ID-0 CODE MUST BE CHANGED - No.#50 Disp. ID-0 New Data 105
SONY	KV20TS32	N/A	POWER SUPPLY IMPROVEMENT - REDUCE AC SPARK WHEN SET IS PLUGGED IN	CHECK/REPLACE REMOVE JUMPERS AT JW603,JW604 AND REPLACE WITH 2.2 RESISTOR (P/N# 1-208-294-11)
SONY	KV20TS32	N/A	UNSTABLE PICTURE - NO PICTURE - POOR FOCUS OR BRIGHTNESS CHANGE	MARK ORIGINAL POSITIONS OF SCREEN AND FOCUS CONTROLS,TURN SCREEN TO MIN./FOCUS TO MAX.-ARCING MAY OCCUR - RESET CTRLS
SONY	KV20TS32	N/A	INTERMITTENT AUDIO AND VIDEO	CHECK/RESOLDER CONNECTIONS ON JUMPER JW98
SONY	KV20TS50	N/A	POWER SUPPLY IMPROVEMENT - REDUCE AC SPARK WHEN SET IS PLUGGED IN	CHECK/REPLACE REMOVE JUMPERS AT JW603,JW604 AND REPLACE WITH 2.2 RESISTOR (P/N# 1-208-294-11)
SONY	KV20TX10	N/A	CLOCK RUNS TOO FAST	ADD 0.1uF TO BASE OF Q103 TO GROUND (P/N# 1-124-463-00)
SONY	KV20TX11	N/A	CLOCK RUNS TOO FAST	ADD 0.1uF TO BASE OF Q103 TO GROUND (P/N# 1-124-463-00)
SONY	KV20TX12	N/A	CLOCK RUNS TOO FAST	ADD 0.1uF TO BASE OF Q103 TO GROUND (P/N# 1-124-463-00)
SONY	KV20TX20	N/A	CLOCK RUNS TOO FAST	ADD 0.1uF TO BASE OF Q103 TO GROUND (P/N# 1-124-463-00)
SONY	KV20V50	N/A	'AFTER GLOW' OF CRT AFTER SET IS SHUT OFF	CHECK/REPLACE IC101 (P/N# 8-752-856-00) ALSO ID-0 CODE MUST BE CHANGED - No.#50 Disp. ID-0 New Data 121
SONY	KV20V50	N/A	UNSTABLE PICTURE - NO PICTURE - POOR FOCUS OR BRIGHTNESS CHANGE	MARK ORIGINAL POSITIONS OF SCREEN AND FOCUS CONTROLS,TURN SCREEN TO MIN./FOCUS TO MAX.-ARCING MAY OCCUR - RESET CTRLS
SONY	KV20V50	N/A	POWER SUPPLY IMPROVEMENT - REDUCE AC SPARK WHEN SET IS PLUGGED IN	CHECK/REPLACE REMOVE JUMPERS AT JW603,JW604 AND REPLACE WITH 2.2 RESISTOR (P/N# 1-208-294-11)
SONY	KV20V50	N/A	SET SHUTS DOWN INTERMITTENTLY	ENTER SERVICE MODE AND SELECT 'SHAP' AND CHANGE DATE FROM 7 TO 5 -IF THIS FAILS,THEN CHANGE IC301 (P/N# 8-752-069-09)
SONY	KV20VM20	N/A	CHIRPING SOUND AT HIGH AC LINE LEVELS	CHECK/REPLACE IC1803
SONY	KV20VM20	N/A	UNIT TICKS AND THEN SHUTSDOWN	CHECK/REPLACE Q1801 2SD1135-C (P/N# 8-729-301-42)
SONY	KV20XBR	N/A	INTERMITTENTLY GOES DEAD - DEAD SET - SHUTS OFF	CHECK/RESOLDER CONNECTIONS ON IC581 AND IC582
SONY	KV20XBR	SCC595CA	NO FUNCTIONS WILL WORK EXCEPT POWER BUTTON	CHECK/REPLACE IC1301
SONY	KV2145	N/A	DARK JAIL BARS ON THE LEFT SIDE AND FADE AS THEY GO TO THE RIGHT	CHECK/REPLACE C539 OPEN
SONY	KV25SXR10	N/A	DARK PICTURE AND RED - INTERMITTENT	CHECK/RESOLDER CONNECTIONS ON DL302
SONY	KV25XBR10	N/A	DARK PICTURE AND RED - INTERMITTENT	CHECK/RESOLDER CONNECTIONS ON DL302
SONY	KV25XBR10	N/A	INTERMITTENTLY GOES DEAD - DEAD SET - SHUTS OFF	CHECK/RESOLDER CONNECTIONS ON IC581 AND IC582
SONY	KV25XBR15	N/A	INTERMITTENTLY GOES DEAD - DEAD SET - SHUTS OFF	CHECK/RESOLDER CONNECTIONS ON IC581 AND IC582
SONY	KV25XBR15	N/A	DARK PICTURE AND RED - INTERMITTENT	CHECK/RESOLDER CONNECTIONS ON DL302
SONY	KV2601	N/A	UNABLE TO CONVERGE AFTER CRT REPLACEMENT	CHECK TO SEE IF SPRING INSIDE ANODE LEAD IS UPSIDE DOWN - FAT PART OF SPRING GOES TOWARDS CRT OPENING
SONY	KV2602R	N/A	UNABLE TO CONVERGE AFTER CRT REPLACEMENT	CHECK TO SEE IF SPRING INSIDE ANODE LEAD IS UPSIDE DOWN - FAT PART OF SPRING GOES TOWARDS CRT OPENING
SONY	KV2625R	N/A	UNABLE TO CONVERGE AFTER CRT REPLACEMENT	CHECK TO SEE IF SPRING INSIDE ANODE LEAD IS UPSIDE DOWN - FAT PART OF SPRING GOES TOWARDS CRT OPENING
SONY	KV2626R	N/A	UNABLE TO CONVERGE AFTER CRT REPLACEMENT	CHECK TO SEE IF SPRING INSIDE ANODE LEAD IS UPSIDE DOWN - FAT PART OF SPRING GOES TOWARDS CRT OPENING
SONY	KV2643R	N/A	UNABLE TO CONVERGE AFTER CRT REPLACEMENT	CHECK TO SEE IF SPRING INSIDE ANODE LEAD IS UPSIDE DOWN - FAT PART OF SPRING GOES TOWARDS CRT OPENING
SONY	KV2644R	N/A	UNABLE TO CONVERGE AFTER CRT REPLACEMENT	CHECK TO SEE IF SPRING INSIDE ANODE LEAD IS UPSIDE DOWN - FAT PART OF SPRING GOES TOWARDS CRT OPENING
SONY	KV2645R	N/A	UNABLE TO CONVERGE AFTER CRT REPLACEMENT	CHECK TO SEE IF SPRING INSIDE ANODE LEAD IS UPSIDE DOWN - FAT PART OF SPRING GOES TOWARDS CRT OPENING
SONY	KV2645RS	N/A	CRT FAILURE PREMATURELY (1-2 YEARS)	CHECK/REPLACE C719 AND L709 ALSO CRT
SONY	KV2645RS	N/A	UNABLE TO CONVERGE AFTER CRT REPLACEMENT	CHECK TO SEE IF SPRING INSIDE ANODE LEAD IS UPSIDE DOWN - FAT PART OF SPRING GOES TOWARDS CRT OPENING
SONY	KV2647R	N/A	UNABLE TO CONVERGE AFTER CRT REPLACEMENT	CHECK TO SEE IF SPRING INSIDE ANODE LEAD IS UPSIDE DOWN - FAT PART OF SPRING GOES TOWARDS CRT OPENING
SONY	KV2647RX	N/A	UNABLE TO CONVERGE AFTER CRT REPLACEMENT	CHECK TO SEE IF SPRING INSIDE ANODE LEAD IS UPSIDE DOWN - FAT PART OF SPRING GOES TOWARDS CRT OPENING
SONY	KV2648R	N/A	UNABLE TO CONVERGE AFTER CRT REPLACEMENT	CHECK TO SEE IF SPRING INSIDE ANODE LEAD IS UPSIDE DOWN - FAT PART OF SPRING GOES TOWARDS CRT OPENING
SONY	KV2649R	N/A	UNABLE TO CONVERGE AFTER CRT REPLACEMENT	CHECK TO SEE IF SPRING INSIDE ANODE LEAD IS UPSIDE DOWN - FAT PART OF SPRING GOES TOWARDS CRT OPENING
SONY	KV2650R	N/A	UNABLE TO CONVERGE AFTER CRT REPLACEMENT	CHECK TO SEE IF SPRING INSIDE ANODE LEAD IS UPSIDE DOWN - FAT PART OF SPRING GOES TOWARDS CRT OPENING
SONY	KV2650RX	N/A	UNABLE TO CONVERGE AFTER CRT REPLACEMENT	CHECK TO SEE IF SPRING INSIDE ANODE LEAD IS UPSIDE DOWN - FAT PART OF SPRING GOES TOWARDS CRT OPENING
SONY	KV2654R	N/A	UNABLE TO CONVERGE AFTER CRT REPLACEMENT	CHECK TO SEE IF SPRING INSIDE ANODE LEAD IS UPSIDE DOWN - FAT PART OF SPRING GOES TOWARDS CRT OPENING
SONY	KV2657R	N/A	UNABLE TO CONVERGE AFTER CRT REPLACEMENT	CHECK TO SEE IF SPRING INSIDE ANODE LEAD IS UPSIDE DOWN - FAT PART OF SPRING GOES TOWARDS CRT OPENING
SONY	KV2665R	N/A	UNABLE TO CONVERGE AFTER CRT REPLACEMENT	CHECK TO SEE IF SPRING INSIDE ANODE LEAD IS UPSIDE DOWN - FAT PART OF SPRING GOES TOWARDS CRT OPENING
SONY	KV2670R	N/A	UNABLE TO CONVERGE AFTER CRT REPLACEMENT	CHECK TO SEE IF SPRING INSIDE ANODE LEAD IS UPSIDE DOWN - FAT PART OF SPRING GOES TOWARDS CRT OPENING
SONY	KV2670RX	N/A	UNABLE TO CONVERGE AFTER CRT REPLACEMENT	CHECK TO SEE IF SPRING INSIDE ANODE LEAD IS UPSIDE DOWN - FAT PART OF SPRING GOES TOWARDS CRT OPENING
SONY	KV2675R	N/A	UNABLE TO CONVERGE AFTER CRT REPLACEMENT	CHECK TO SEE IF SPRING INSIDE ANODE LEAD IS UPSIDE DOWN - FAT PART OF SPRING GOES TOWARDS CRT OPENING
SONY	KV2676R	N/A	UNABLE TO CONVERGE AFTER CRT REPLACEMENT	CHECK TO SEE IF SPRING INSIDE ANODE LEAD IS UPSIDE DOWN - FAT PART OF SPRING GOES TOWARDS CRT OPENING
SONY	KV2680R	N/A	UNABLE TO CONVERGE AFTER CRT REPLACEMENT	CHECK TO SEE IF SPRING INSIDE ANODE LEAD IS UPSIDE DOWN - FAT PART OF SPRING GOES TOWARDS CRT OPENING
SONY	KV2681R	N/A	UNABLE TO CONVERGE AFTER CRT REPLACEMENT	CHECK TO SEE IF SPRING INSIDE ANODE LEAD IS UPSIDE DOWN - FAT PART OF SPRING GOES TOWARDS CRT OPENING
SONY	KV2686R	N/A	UNABLE TO CONVERGE AFTER CRT REPLACEMENT	CHECK TO SEE IF SPRING INSIDE ANODE LEAD IS UPSIDE DOWN - FAT PART OF SPRING GOES TOWARDS CRT OPENING
SONY	KV2690R	N/A	UNABLE TO CONVERGE AFTER CRT REPLACEMENT	CHECK TO SEE IF SPRING INSIDE ANODE LEAD IS UPSIDE DOWN - FAT PART OF SPRING GOES TOWARDS CRT OPENING
SONY	KV2691R	N/A	UNABLE TO CONVERGE AFTER CRT REPLACEMENT	CHECK TO SEE IF SPRING INSIDE ANODE LEAD IS UPSIDE DOWN - FAT PART OF SPRING GOES TOWARDS CRT OPENING
SONY	KV2697R	N/A	UNABLE TO CONVERGE AFTER CRT REPLACEMENT	CHECK TO SEE IF SPRING INSIDE ANODE LEAD IS UPSIDE DOWN - FAT PART OF SPRING GOES TOWARDS CRT OPENING
SONY	KV27	ALL 27'' SETS	HIGH PITCHED NOISE OR BUZZING FROM THE YOKE ORIGINAL YOKE P/N# 1-451-275-31	CHECK/REPLACE WITH NEW TYPE (P/N# 1-451-275-41)
SONY	KV2726R	N/A	INTERMITTENT TUNER OPERATION	CHECK/RESOLDER CONNECTIONS ON ALL IF TRANSFORMERS IN 'IF' BLOCK
SONY	KV2781R	N/A	INTERMITTENT PICTURE,VOLUME, CHANNEL UP/DOWN BUTTONS	CHECK/REPLACE CP-104 CAPACITOR PACK FOR LEAKAGE - REPLACE WITH INDIVIDUAL CAPACITORS (4) (P/N# 1-102-978-00)
SONY	KV2790R	N/A	WON'T LOCK ON STATION - AFT PROBLEM	READJUST T203
SONY	KV2792R	N/A	WON'T TUNE AT ALL	CHECK/REPLACE Q1411 AND Q1412
SONY	KV27DS21	N/A	AFT PROBLEMS OR INTERMITTENT SOUND AND PICTURE	CHECK/RESOLDER CONNECTIONS ON 'IF' COILS IN 'IF BLOCK' ASSEMBLY
SONY	KV27DST1	N/A	DEAD SET - MISSING 5 VOLT STANDBY VOLTAGE	CHECK/REPLACE IC602 (P/N# 8-759-805-37), R636 (1.5?- P/N# 1-249-383-11) AND D638 (P/N# 8-719-911-19)
SONY	KV27DST1	N/A	WON'T STORE THE SERVICE SETTINGS	CHECK/REPLACE IC102 (8-759-251-04)
SONY	KV27EXR10	N/A	PICTURE BLINKS ON AND OFF WHEN FIRST TURNED ON	CHECK/REPLACE R702 ON 'C' BOARD (1m )
SONY	KV27EXR10	N/A	DEAD SET - RELAY WILL NOT CLICK	CHECK/REPLACE RY601 RELAY (P/N# 1-515-738-11)
SONY	KV27EXR10	N/A	DEAD SET WITH A BUZZ COMING FROM POWER SUPPLY	CHECK/REPLACE D625 (P/N# ECG588 OR 8-719-948-59)
SONY	KV27EXR10	N/A	CLOCK RUNS TOO FAST	CHANGE C125 TO A 0.1uF @ 50v CAPACITOR (P/N# 1-124-463-00)
SONY	KV27EXR10	N/A	CLOCK RUNS TOO FAST	ADD 0.1uF TO BASE OF Q108 TO GROUND (P/N# 1-124-463-00)
SONY	KV27EXR10	N/A	IMMEDIATE SHUTDOWN - DISABLING PROTECTION CIRCUIT WILL ALLOW SET TO RUN NORMALLY - ALL VOLTAGES FINE	CHECK/REPLACE Q607 (P/N# 8-729-423-37) OR ECG289A AND ALSO Q608 (P/N# 8-729-423-44) OR ECG290A
SONY	KV27EXR15	N/A	CLOCK RUNS TOO FAST	ADD 0.1uF TO BASE OF Q108 TO GROUND (P/N# 1-124-463-00)
SONY	KV27EXR15	N/A	CLOCK RUNS TOO FAST	CHANGE C125 TO A 0.1uF @ 50v CAPACITOR (P/N# 1-124-463-00)
SONY	KV27EXR15	N/A	PICTURE GETS DARK INTERMITTENTLY - COLOR ONLY	CHECK/RESOLDER CONNECTIONS ON R739 AND Q711
SONY	KV27EXR15	N/A	DEAD SET WITH A BUZZ COMING FROM POWER SUPPLY	CHECK/REPLACE D625 (P/N# ECG588 OR 8-719-948-59)
SONY	KV27EXR15	N/A	DEAD SET - RELAY WILL NOT CLICK	CHECK/REPLACE RY601 RELAY (P/N# 1-515-738-11)
SONY	KV27EXR15	N/A	IMMEDIATE SHUTDOWN - DISABLING PROTECTION CIRCUIT WILL ALLOW SET TO RUN NORMALLY - ALL VOLTAGES FINE	CHECK/REPLACE Q607 (P/N# 8-729-423-37) OR ECG289A AND ALSO Q608 (P/N# 8-729-423-44) OR ECG290A
SONY	KV27EXR20	N/A	CLOCK RUNS TOO FAST	CHANGE C125 TO A 0.1uF @ 50v CAPACITOR (P/N# 1-124-463-00)
SONY	KV27EXR20	N/A	DEAD SET WITH A BUZZ COMING FROM POWER SUPPLY	CHECK/REPLACE D625 (P/N# ECG588 OR 8-719-948-59)
SONY	KV27EXR20	N/A	NO HORZ. DRIVE FROM IC301 PIN 37	CHECK/REPLACE D307
SONY	KV27EXR20	N/A	IMMEDIATE SHUTDOWN - DISABLING PROTECTION CIRCUIT WILL ALLOW SET TO RUN NORMALLY - ALL VOLTAGES FINE	CHECK/REPLACE Q607 (P/N# 8-729-423-37) OR ECG289A AND ALSO Q608 (P/N# 8-729-423-44) OR ECG290A
SONY	KV27EXR20	N/A	SOUND BUT NO PICTURE	CHECK/REPLACE C536
SONY	KV27EXR20	N/A	DEAD SET - RELAY WILL NOT CLICK	CHECK/REPLACE RY601 RELAY (P/N# 1-515-738-11)
SONY	KV27EXR20	N/A	CLOCK RUNS TOO FAST	ADD 0.1uF TO BASE OF Q108 TO GROUND (P/N# 1-124-463-00)
SONY	KV27EXR20	N/A	LOUD BUZZING SOUND AND NO LEFT CHANNEL AUDIO	CHECK/REPLACE IC405
SONY	KV27EXR20	N/A	SOUND OK BUT PICTURE IS INTERMITTENT - MAY BE WORST WHEN SET IS COLD	CHECK/REPLACE C536 (10uF @ 50v)
SONY	KV27EXR20	N/A	WILL NOT TURN ON WHEN COLD	CHECK/REPLACE C655
SONY	KV27EXR25	N/A	IMMEDIATE SHUTDOWN - DISABLING PROTECTION CIRCUIT WILL ALLOW SET TO RUN NORMALLY - ALL VOLTAGES FINE	CHECK/REPLACE Q607 (P/N# 8-729-423-37) OR ECG289A AND ALSO Q608 (P/N# 8-729-423-44) OR ECG290A
SONY	KV27EXR25	N/A	CLOCK RUNS TOO FAST	ADD 0.1uF TO BASE OF Q108 TO GROUND (P/N# 1-124-463-00)
SONY	KV27EXR25	N/A	DEAD SET - RELAY DOES CLICK	CHECK/REPLACE IC651 (P/N# 8-749-920-81 OR STR-S6301A)
SONY	KV27EXR25	N/A	DEAD SET - RELAY WILL NOT CLICK	CHECK/REPLACE RY601 RELAY (P/N# 1-515-738-11)
SONY	KV27EXR25	N/A	CLOCK RUNS TOO FAST	CHANGE C125 TO A 0.1uF @ 50v CAPACITOR (P/N# 1-124-463-00)
SONY	KV27EXR25	N/A	DEAD SET WITH A BUZZ COMING FROM POWER SUPPLY	CHECK/REPLACE D625 (P/N# ECG588 OR 8-719-948-59)
SONY	KV27EXR90	N/A	DEAD SET WITH A BUZZ COMING FROM POWER SUPPLY	CHECK/REPLACE D625 (P/N# ECG588 OR 8-719-948-59)
SONY	KV27EXR90	N/A	CLOCK RUNS TOO FAST	ADD 0.1uF TO BASE OF Q108 TO GROUND (P/N# 1-124-463-00)
SONY	KV27EXR95	N/A	CLOCK RUNS TOO FAST	ADD 0.1uF TO BASE OF Q108 TO GROUND (P/N# 1-124-463-00)
SONY	KV27EXR95	N/A	DEAD SET WITH A BUZZ COMING FROM POWER SUPPLY	CHECK/REPLACE D625 (P/N# ECG588 OR 8-719-948-59)
SONY	KV27FX10	N/A	CLOCK RUNS TOO FAST	CHANGE C125 TO A 0.1uF @ 50v CAPACITOR (P/N# 1-124-463-00)
SONY	KV27FX10	N/A	CLOCK RUNS TOO FAST	ADD 0.1uF IN PARALLEL WITH D104 (P/N# 1-124-463-00)
SONY	KV27HFR10	N/A	CLOCK RUNS TOO FAST	CHANGE C125 TO A 0.1uF @ 50v CAPACITOR (P/N# 1-124-463-00)
SONY	KV27HFR15	N/A	CLOCK RUNS TOO FAST	CHANGE C125 TO A 0.1uF @ 50v CAPACITOR (P/N# 1-124-463-00)
SONY	KV27HFR20	N/A	CLOCK RUNS TOO FAST	CHANGE C125 TO A 0.1uF @ 50v CAPACITOR (P/N# 1-124-463-00)
SONY	KV27HFR25	N/A	CLOCK RUNS TOO FAST	CHANGE C125 TO A 0.1uF @ 50v CAPACITOR (P/N# 1-124-463-00)
SONY	KV27HSR10	N/A	VERTICAL FOLDOVER AT TOP OF PICTURE	CHECK/REPLACE C501
SONY	KV27HSR10	N/A	HORZ RED,BLUE AND GREEN LINES IN THE PICTURE	CHECK/REPLACE R517 (P/N# 1-216-355-91) , IC500,IC301
SONY	KV27HSR10	N/A	DEAD SET - POWER SUPPLY SQUEALS	CHECK/REPLACE Q503 (2SD1555) SHORTED
SONY	KV27HSR10	N/A	DEAD SET	CHECK/RESOLDER CONNECTIONS ON IC581 AND IC582
SONY	KV27HSR10	N/A	PINCUSHION DISTORTION	CHECK/REPLACE L501,R571 AND Q505 AND CHECK TO SEE IF D512 IS PENETRATING THRU CIRCUIT BOARD
SONY	KV27HSR10	N/A	UNABLE TO EXIT THE SERVICE MODE	CLEAN CONNECTOR U20
SONY	KV27HSR10	N/A	PICTURE BLANKS ON IN-ACTIVE STATIONS	CHECK/REPLACE D303 ON THE 'A' BOARD
SONY	KV27HSR10	N/A	MANUAL POWER BUTTON WILL NOT WORK	CHECK/REPLACE C125 - REPLACE WITH A BI-POLAR TYPE (P/N# 1-124-272-91)
SONY	KV27HSR10	N/A	DEAD SET BUT RELAY DOES CLICK	CHECK/REPLACE IC651 (P/N# 8-749-920-81 OR STR-S6301A)
SONY	KV27HSR10	N/A	DEAD SET WITH A THUMP THUMP IN SPEAKERS - NO HIGH VOLTAGE	CHECK/REPLACE Q604 (P/N# 8-729-119-78)
SONY	KV27HSR10	N/A	RETRACE LINES VISIBLE AT THE TOP OF SCREEN	CHECK TO SEE IF SERVICE MODE 'REF' IS SET CORRECTLY - IT SHOULD BE SET AT 1 BUT RETRACE WILL APPEAR WHEN SET TO 0
SONY	KV27HSR10	N/A	CLOCK RUNS TOO FAST	ADD 0.1uF TO BASE OF Q105 TO GROUND (P/N# 1-124-463-00)
SONY	KV27HSR10	ANU1	REPLACED COMB FILTER WITH NEW TYPE AND SET HAD NO VIDEO	ADD R1367 (1.2k) AND R1369 (1.2k)
SONY	KV27HSR10	ANU1	REPEATED FAILURE OF THE HORZ. OUTPUT XSTR.	CHECK/REPLACE WITH NEW TYPE P/N# 8-729-016-32 AND CHANGE R523 TO A 0.68 ohm P/N# 1-216-347-11
SONY	KV27HX1	N/A	DEAD SET - MISSING 5 VOLT STANDBY VOLTAGE	CHECK/REPLACE IC602 (P/N# 8-759-805-37), R636 (1.5?- P/N# 1-249-383-11) AND D638 (P/N# 8-719-911-19)
SONY	KV27HX1	N/A	WON'T STORE THE SERVICE SETTINGS	CHECK/REPLACE IC102 (8-759-251-04)
SONY	KV27S10	N/A	SPEAKERS RATTLE	CHECK TO SEE IF 'SONY' LOGO IS LOOSE, IF SO GLUE IN PLACE - ALSO APPLY A SMALL AMOUNT OF RTV CEMENT TO SPEAKER GROMMETS
SONY	KV27S10	N/A	IMPROVEMENT OF POWER SUPPLY CIRCUIT	CHECK/REPLACE JUMPER WIRE LOCATED AT R683 AND R684 WITH A 1 @ 10w RESISTOR (P/N# 1-205-998-11)
SONY	KV27S10	N/A	DEAD SET	CHECK/REPLACE DEFLECTION YOKE
SONY	KV27S10	N/A	SQUEAL FROM HORIZONTAL LINEARITY COIL	CHECK/REPLACE L509 (P/N# 1-409-861-11)
SONY	KV27S10	N/A	DEAD SET	CHECK R607 (P/N# 120293361), Q601/Q602 (P/N# 872901951), VDR601 (P/N# 180728811), VDR602,VDR603 (P/N# 181005311)
SONY	KV27S10	N/A	INSUFFICIENT VERTICAL DEFLECTION	CHECK/REPLACE DEFLECTION YOKE
SONY	KV27S10	N/A	REPEATED FAILURE OF THE HORZ. DRIVER TRANSISTOR	REMOVE JUMPER ACROSS R515 AND INSTALL A .33 @ 2w. RESISTOR
SONY	KV27S10	N/A	NO PICTURE DUE TO FAILURE OF IC301	CHECK/REPLACE IC301 AND ADD D308 (P/N# 8-719-110-17) 10v ZENER - CATHODE TO IC301 PIN #37 AND ANODE TO GROUND
SONY	KV27S10	N/A	SET SHUTS DOWN INTERMITTENTLY	ENTER SERVICE MODE AND SELECT 'SHAP' AND CHANGE DATE FROM 7 TO 5 -IF THIS FAILS,THEN CHANGE IC301 (P/N# 8-752-069-09)
SONY	KV27S15	N/A	NO PICTURE DUE TO FAILURE OF IC301	CHECK/REPLACE IC301 AND ADD D308 (P/N# 8-719-110-17) 10v ZENER - CATHODE TO IC301 PIN #37 AND ANODE TO GROUND
SONY	KV27S15	N/A	SQUEAL FROM HORIZONTAL LINEARITY COIL	CHECK/REPLACE L509 (P/N# 1-409-861-11)
SONY	KV27S15	N/A	SPEAKERS RATTLE	CHECK TO SEE IF 'SONY' LOGO IS LOOSE, IF SO GLUE IN PLACE - ALSO APPLY A SMALL AMOUNT OF RTV CEMENT TO SPEAKER GROMMETS
SONY	KV27S15	N/A	DEAD SET	CHECK R607 (P/N# 120293361), Q601/Q602 (P/N# 872901951), VDR601 (P/N# 180728811), VDR602,VDR603 (P/N# 181005311)
SONY	KV27S15	N/A	IMPROVEMENT OF POWER SUPPLY CIRCUIT	CHECK/REPLACE JUMPER WIRE LOCATED AT R683 AND R684 WITH A 1 @ 10w RESISTOR (P/N# 1-205-998-11)
SONY	KV27S20	N/A	INTERMITTENT OR CONSTANT NO SOUND/PICTURE OR NOISE IN SOUND AND PICTURE	CHECK/RESOLDER CONNECTIONS ON PINS #1 THRU #6 ON TUNER - IF THIS DOESN'T SOLVE THE PROBLEM, REPLACE TUNER
SONY	KV27S20	N/A
SONY	KV27S25	N/A	NO HIGH VOLTAGE - SOUND OK	CHECK/REPLACE IC351
SONY	KV27S25	N/A	INTERMITTENT OR CONSTANT NO SOUND/PICTURE OR NOISE IN SOUND AND PICTURE	CHECK/RESOLDER CONNECTIONS ON PINS #1 THRU #6 ON TUNER - IF THIS DOESN'T SOLVE THE PROBLEM, REPLACE TUNER
SONY	KV27S25	N/A
SONY	KV27S35	N/A	INTERMITTENT LOSS OF CHANNELS OR NO TUNING ON MAIN PIX TUNER	CHECK/RESOLDER CONNECTIONS ON TU102 WHERE TUNER IS SOLDER TO MAIN PCB
SONY	KV27S35	N/A	INTERMITTENT OR CONSTANT NO SOUND/PICTURE OR NOISE IN SOUND AND PICTURE	CHECK/RESOLDER CONNECTIONS ON PINS #1 THRU #6 ON TUNER - IF THIS DOESN'T SOLVE THE PROBLEM, REPLACE TUNER
SONY	KV27S35	N/A	NO AUDIO FROM THE LEFT CHANNEL	CHECK/REPLACE IC1401
SONY	KV27SXR10	N/A	CLOCK RUNS TOO FAST	ADD 0.1uF TO BASE OF Q103 TO GROUND (P/N# 1-124-463-00)
SONY	KV27SXR10	N/A	INTERMITTENT LOSS OF VIDEO	CHECK/RESOLDER CONNECTIONS ON DL301
SONY	KV27SXR10	N/A	INTERMITTENT LOSS OF VIDEO - CHROMA AND AUDIO ARE NORMAL	CHECK/RESOLDER CONNECTIONS ON DL302
SONY	KV27SXR11	N/A	CLOCK RUNS TOO FAST	ADD 0.1uF TO BASE OF Q103 TO GROUND (P/N# 1-124-463-00)
SONY	KV27TR10	N/A	CLOCK RUNS TOO FAST	ADD 0.1uF TO BASE OF Q103 TO GROUND (P/N# 1-124-463-00)
SONY	KV27TR20	N/A	CLOCK RUNS TOO FAST	ADD 0.1uF TO BASE OF Q103 TO GROUND (P/N# 1-124-463-00)
SONY	KV27TR21	N/A	CLOCK RUNS TOO FAST	ADD 0.1uF TO BASE OF Q103 TO GROUND (P/N# 1-124-463-00)
SONY	KV27TR22	N/A	CLOCK RUNS TOO FAST	ADD 0.1uF TO BASE OF Q103 TO GROUND (P/N# 1-124-463-00)
SONY	KV27TS11	N/A	VERY DARK PICTURE	CHECK/REPLACE C570
SONY	KV27TS11	N/A	CLOCK RUNS TOO FAST	ADD 0.1uF TO BASE OF Q103 TO GROUND (P/N# 1-124-463-00)
SONY	KV27TS11	N/A	REPEATED FAILURE OF Q501 (HORZ. OUTPUT XSTR.)	CHECK/RESOLDER CONNECTIONS ON T502
SONY	KV27TS20	N/A	CLOCK RUNS TOO FAST	ADD 0.1uF TO BASE OF Q103 TO GROUND (P/N# 1-124-463-00)
SONY	KV27TS20	N/A	NO HORZ. SYNC - VERTICAL SYNC OK BUT DOES TRY TO FOLDOVER	CHECK/REPLACE C509
SONY	KV27TS20	N/A	REPEATED FAILURE OF Q501 (HORZ. OUTPUT XSTR.)	CHECK/RESOLDER CONNECTIONS ON T502
SONY	KV27TS20	N/A	VERY DARK PICTURE -- G1 CONTROL HAS NO EFFECT	CHECK/REPLACE D518 (P/N# ECG551) AND R587 (1.8k?@ 1watt)
SONY	KV27TS20	N/A	DEAD SET - NO CLICK	CHECK/REPLACE D601 BRIDGE RECTIFIER AND F601 FUSE
SONY	KV27TS21	N/A	REPEATED FAILURE OF Q501 (HORZ. OUTPUT XSTR.)	CHECK/RESOLDER CONNECTIONS ON T502
SONY	KV27TS21	N/A	CLOCK RUNS TOO FAST	ADD 0.1uF TO BASE OF Q103 TO GROUND (P/N# 1-124-463-00)
SONY	KV27TS21	N/A	DISTORTED PINCUSHION	CHECK/REPLACE D513
SONY	KV27TS22	N/A	CLOCK RUNS TOO FAST	ADD 0.1uF TO BASE OF Q103 TO GROUND (P/N# 1-124-463-00)
SONY	KV27TS22	N/A	REPEATED FAILURE OF Q501 (HORZ. OUTPUT XSTR.)	CHECK/RESOLDER CONNECTIONS ON T502
SONY	KV27TS23	N/A	REPEATED FAILURE OF Q501 (HORZ. OUTPUT XSTR.)	CHECK/RESOLDER CONNECTIONS ON T502
SONY	KV27TS23	N/A	CLOCK RUNS TOO FAST	ADD 0.1uF TO BASE OF Q103 TO GROUND (P/N# 1-124-463-00)
SONY	KV27TS24	N/A	CLOCK RUNS TOO FAST	ADD 0.1uF TO BASE OF Q103 TO GROUND (P/N# 1-124-463-00)
SONY	KV27TS24	N/A	REPEATED FAILURE OF Q501 (HORZ. OUTPUT XSTR.)	CHECK/RESOLDER CONNECTIONS ON T502
SONY	KV27TS25	N/A	REPEATED FAILURE OF Q501 (HORZ. OUTPUT XSTR.)	CHECK/RESOLDER CONNECTIONS ON T502
SONY	KV27TS25	N/A	CLOCK RUNS TOO FAST	ADD 0.1uF TO BASE OF Q103 TO GROUND (P/N# 1-124-463-00)
SONY	KV27TS25	N/A	DARK PICTURE	CHECK/REPLACE R587 AND D518
SONY	KV27TS26	N/A	CLOCK RUNS TOO FAST	ADD 0.1uF TO BASE OF Q103 TO GROUND (P/N# 1-124-463-00)
SONY	KV27TS26	N/A	REPEATED FAILURE OF Q501 (HORZ. OUTPUT XSTR.)	CHECK/RESOLDER CONNECTIONS ON T502
SONY	KV27TS27	N/A	INTERMITTENT PICTURE OR SNOW	CHECK/RESOLDER CONNECTIONS IN TUNER WHERE CASING IS SOLDERED TO PCB NEAR 4TH FEED THRU BACK FROM ANTENNA INPUT
SONY	KV27TS27	N/A	REPEATED FAILURE OF Q501 (HORZ. OUTPUT XSTR.)	CHECK/RESOLDER CONNECTIONS ON T502
SONY	KV27TS27	N/A	INTERMITTENT NO RECEPTION - SNOW ONLY - WIGGLING COAX CONNECTOR ON REAR OF SET WILL RESTORE TEMPORARILY	CHECK/RESOLDER ALL FEED THRU CONNECTIONS INSIDE TUNER OR REPLACE TUNER (P/N# 1-465-371-11)
SONY	KV27TS27	N/A	DEAD SET - NO RELAY CLICK	CHECK/REPLACE D622 (8-719-510-02) OR ECG552 AND ALSO R647 (1-249-385-11) 2.2 1/2w.
SONY	KV27TS27	N/A	SOUND IS MUFFLED AND VOLUME IS LOW	CHECK/REPLACE MM201 (P/N# 8-741-637-11)
SONY	KV27TS27	N/A	TUNER DRIFTS/AFC PROBLEM - A NEW TUNER HAS BEEN TRIED	CHECK/REPLACE IC606 (5 VOLT REGULATOR)
SONY	KV27TS27	N/A	INTERMITTENT POWER UP - NO PICTURE	CHECK/REPLACE VERTICAL OUTPUT IC
SONY	KV27TS27	N/A	DEAD WITH NO STANDBY VOLTAGES	CHECK/REPLACE R647,Q601,Q602,D622,C650
SONY	KV27TS27	N/A	DEAD SET	CHECK/REPLACE Q614 AND IC607
SONY	KV27TS27	N/A	FAILURE OR REPEATED FAILURE OF Q601 AND Q602	CHECK/REPLACE Q601,Q602 AND CHANGE R647 TO NEW PART (P/N 1-249-381-11)
SONY	KV27TS27	N/A	VERY DARK PICTURE	CHECK/REPLACE Q301
SONY	KV27TS27	N/A	CLOCK RUNS TOO FAST	ADD 0.1uF IN PARALLEL WITH C121 (P/N# 1-124-463-00)
SONY	KV27TS29	N/A	NO PICTURE DUE TO FAILURE OF IC301	CHECK/REPLACE IC301 AND ADD D308 (P/N# 8-719-110-17) 10v ZENER - CATHODE TO IC301 PIN #37 AND ANODE TO GROUND
SONY	KV27TS29	N/A	HIGH PITCHED SQEAUL FROM CHASSIS CHANGE C503 (1-124-557-11), T501 (1-453-146-11) AND	CHANGE L509 (1-460-173-21),L510 (1-406-607-11), MOVE C519 & C548 AWAY FROM SHIELD, SILICONE JW505 BETWEEN R527 & L508
SONY	KV27TS29	N/A	IMPROVEMENT OF POWER SUPPLY CIRCUIT	CHECK/REPLACE JUMPER WIRE LOCATED AT R683 AND R684 WITH A 1 @ 10w RESISTOR (P/N# 1-205-998-11)
SONY	KV27TS29	N/A	RETRACE LINES IN PICTURE AND DISTORTED SOUND WITH POPPING	CHECK/REPLACE FLYBACK XFRM.

LAMSON Digital Electronics Address: 1324-1326 Jose Abad Santos Ave.,Manila, Philippines TEL:00632-2559675  TEL/FAX:00632-2568130 Cellular:0922-8867809 0922-8867810 E-mail:[email protected]    YAHOO MESSENGER ID : myrna_q_ng or saishu_ng SKYPE ID: myrna_q_ng or saishu_ng (old) Lamson Importers & Exporters Trading <We will not be using the old address and phone no. in the future. Please be noted when calling us, sending letters, parcels or buying our products> OLD Address: 681 Carmen Building, Ronquillo St. Quiapo, Manila, Philippines Phone:00632-7332936 7332940 Fax:00632-7332940 E-mail: