VCR REPAIR TIPS PAGE 2

MAKE	MODEL	CHASSIS	SYMPTOM	CURE
GE	1CVD5023X	N/A	ERRATIC REEL MOTOR--MAY ALSO HAVE A HIGH PITCHED WHINE	CHECK C2523 FOR OPEN
GE	1CVT645	N/A	DISPLAY MISSING--NO FUNCTIONS	CHECK C7507 FOR LEAKAGE
GE	1VCR3000X	N/A	NO SPEED SELECT	IC601
GE	1VCR4012X	N/A	DEAD WITH OPEN FUSE	CHECK D1001,Q1001,R1003
GE	1VCR4012X	N/A	PIX JITTERS ON SPECIAL EFFECTS	CHECK V-LOCK ADJUSTMENT-WORN HEADS-PG SHIFTERS TR.FIX
GE	1VCR4012X	N/A	ALL MODES OPERATIONAL NO FIP DISPLAY	CHECK FILAMENT VOLT.MISSING CHECKPINS7&8 OF T1001
GE	1VCR4012X	N/A	WHEN PLAY IS PRESSED,VCR RUNS FOR 2-5 SECONDS THEN SHUTS OFF-NEVER SWITCHES FROM TUNER TO VCR-LOADING MOTOR RUNS ON	CHECK/REPLACE MODE SELECT SWITCH
GE	1VCR4012X	N/A	WEAK AUDIO (PLAYBACK ONLY)	CHECK C4014
GE	1VCR4012X	N/A	NO EE OR VV VIDEO AUDIO OK	CHECK/REPLACE IC3101
GE	1VCR4012X	N/A	CAPSTAN MOTOR RUNS ABOUT 8SEC. THEN SHUTS DOWN	CHECK R6070
GE	1VCR4012X	N/A	VIDEO FROM RF VIDEO OUTLOOKS SCRAMBLED	CHECK VIDEO SIGNAL ON BOTH SIDES OF C3014
GE	1VCR4012X	N/A	SQUEL FROM THE POWER SUPP WHEN PLUGGED IN	CHECK D1023
GE	1VCR4012X	N/A	WILL NOT RECORD WHEN TIMER IS SET	CHECK/CLEAN ERASE PROTECT SWITCH CONTACTS
GE	1VCR4012X	N/A	NO POWER UP--FIP OK,POWER SUPPLY OK	CK PIN #16 OF IC6001 (4-5V)--IF LOW,CK C6009
GE	1VCR4012X	N/A	GARBLED AUDIO IN LP AND SLP	CHECK PINCH ROLLER,CLUTCH ASSY.;IDLER
GE	1VCR4012X	N/A	TRACKING ADJUSTMENTS	MOST ACCURATELY PERFORMED IN SP MODE.
GE	1VCR4012X	N/A	EXCESSIVE WOW AND FLUTTER	CHECK/REPLACE C2004 (BREAKING DOWN UNDER LOAD OR HIGH ESR)
GE	1VCR4012X	N/A	POWERS UP-LOADS TAPE-NO PLAY,REC,EJECT,FF,REW	REPLACE IC7501
GE	1VCR4012X	N/A	CAPSTAN MOTOR OSCILLATES BACK & FORTH	REPLACE IC2002
GE	1VCR4012X	N/A	STARTS PLAYING THEN STOPS;COUNTER DOESN'T WORK	CHECK IC1551
GE	1VCR4012X	N/A	NO COLOR ON PLAYBACK OF PRE-RECORDED TAPES	CHECK/REPLACE IC8101 (MN6163)
GE	1VCR4012X	N/A	AFTER POWER IS APPLIED CAPSTAN SPINS FORFEW SECS	CHECK/ REPLACE Q6003 IN MICROPROCESSOR CIRCUIT
GE	1VCR4012X	N/A	NO COLOR IN PLAY BACK ONLY	REPLACE IC3502 ON THE HEAD AMP CBA
GE	1VCR4012X	N/A	AFTER POWER IS APPLIED CAPSTAN SPINS FOR A FEW S	CHECK / REPLACE Q6003 IN MICROPROCESSOR CIRCUIT
GE	1VCR4012X	N/A	NO AUDIO	CHECK/REPLACE Q7010 & Q7002
GE	1VCR4012X	N/A	FAILURE TO PASS LEAKAGE CURRENT HOT CHECK	CHECK OR REPLACE C1005
GE	1VCR4012X	N/A	DISTORTION OF CASSETTE TRAY SIDE PLATE	CHECK R6070 RC00043,PLOO144,IC6001
GE	1VCR4012X	N/A	POWER SUPPLY TICKS WHEN PLUGGED IN AND ALL SECONDARY VOLTAGES ARE LOW.	CHECK R1002 (680k) FOR OPEN
GE	1VCR4012X	N/A	PUSH PLAY AND TAPE GOES TO REWIND	CHECK/REPLACE END SENSORS
GE	1VCR4012X	N/A	SNOWY PIX IN PLAYBACK ONLY AUDIO OK	CHECK Q3001
GE	1VCR4012X	N/A	TOP & BOTTOM 2' OF PIX. OK CENTER SNOWY	CHECK OR REPLACE IC8102
GE	1VCR4012X	N/A	NO TRACKING CONTROL MAY LOCK IN BRIEFLY	CHECK/REPLACE IC2002
GE	1VCR4012X	N/A	UNIT TICKS WHEN PLUGGED IN NO FIP	R1039
GE	1VCR4012X	N/A	INTERMITTENTLY STOPS PLAYING W/KNOWN GOOD TAPE	CHECK Q1552 (SUPPLY PHOTO XSTR)
GE	1VCR4012X	N/A	NO COLOR	ADJUST VCO,VXO--CHECK 3.58MHZ,4.2MHZ,629KHZ
GE	1VCR4012X	N/A	WON'T RECORD -- MANUAL OR OTR	CLEAN OR REPLACE ERASE PROTECT SWITCH
GE	1VCR4012X	N/A	WON'T POWER UP--DRUM RUNS CONTINUOUSLY	REPLACE IC6001 (MN15846VRG)
GE	1VCR4012X	N/A	REDUCED CLOCK & DAY BRILLIANCE	CHECK R1215
GE	1VCR4012X	N/A	NO AUTO STOP AT END OF TAPE IN PLAY FAST FOR REW	CHECK/REPLACE Q6008
GE	1VCR5002X	N/A	PIX JITTERS ON SPECIAL EFFECTS	CHECK V-LOCK ADJUSTMENT-WORN HEADS-PG SHIFTERS TR.FIX
GE	1VCR5002X	N/A	PLAYBACK/RECORD ONLY IN SP LP&SLP CAPSTAN QUIVER	READJUSTMENT OF THE FG HEAD
GE	1VCR5002X	N/A	TAPE LEFT HANGING FROM CASSETTE;IDLER OK	CHECK MODE SELECT SWITCH
GE	1VCR5002X	N/A	PLAYS HALF OF TAPE CAPSTAN DRIVE IC HOT	REPLACE CAPSTAN BEARING ASSEMBLY
GE	1VCR5002X	N/A	TRACKING ADJUSTMENTS	MOST ACCURATELY PERFORMED IN SP MODE.
GE	1VCR5002X	N/A	NO FIPS OPERATION CYLD. MOTOR RUNS ALL THE TIME	IF POWER SUPPLY VOLTAGES ARE LOW CHECK D1006
GE	1VCR5002X	N/A	NO POWER NO DISPLAY FUSE OK	CHECK FOR DEFECTIVE Q1 INTHE POWER SUPPLY
GE	1VCR5002X	N/A	DEAD SET BUT NO FUSES BLOWN	CHECK/REPLACE Q1001,D1007 AND D1005
GE	1VCR5002X	N/A	WILL NOT TIME RECORD	CLEAN THE POINTS ON AND/OR REPLACE THE SAFETY SWITCH
GE	1VCR5002X	N/A	STOPS OR SHUTDOWN AFTER 1 TO 2 HOURS OF PLAYING	REPLACE THE CAPSTAN HOUSING
GE	1VCR5002X	N/A	EXCESSIVE BRIGHTNESS IN PLAYBACK;E-E PIX OK	ADJUST WHITE CLIP R3101 (REFER TO MANUAL)
GE	1VCR5002X	N/A	ERRATIC FUNCTIONS--PLAY>STOP RESULTS PLAY>REWIND	CHECK FOR DIRTY MODE SELECT SWITCH OR SWITCH TIMING.
GE	1VCR5002X	N/A	WILL NOT RECORD OR PLAYBACK AUDIO	CHECK/REPLACE IC4003
GE	1VCR5002X	N/A	ERRATIC CAPSTAN MOTOR OPERATION	CHECK/REPLACE IC2601
GE	1VCR5002X	N/A	INTERMITTENT NORMAL PIX TO SNOW AFTER SEVERAL HO	REPLACE IC2001
GE	1VCR5002X	N/A	CAPSTAN STOPS AFTER 1/2 HOUR--IC VERY HOT!!!	CHECK CAPSTAN BEARINGS OR FLYWHEEL FOR SCARS
GE	1VCR5002X	N/A	TAPE LOADS IS IMMEDIATELY EJECTED	CHECK D6013 FOR LEAKAGE
GE	1VCR5002X	N/A	HORIZ. ROLLING LINES IN PIX WITH VCR OFF	CHECK OR REPLACE THE VHF BLOCK
GE	1VCR5002X	N/A	WHEN PLAY BUTTON IS PRESSED ALL DISP. SEG. GOOUT	CHECK Q1001
GE	1VCR5002X	N/A	WILL NOT GO INTO RECORD MAY CONT UNLOAD AND LOAD	REPLACE THE MODE SELECT SWITCH
GE	1VCR5002X	N/A	REACTION TIME TO ALL FUNCTIONS IS SLOW	CHECK MODE SELECT SWITCH
GE	1VCR5002X	N/A	LEAVES THE TAPE HANGING FROM EJECTED CASSETTE	CHECK THE FELT ON THE TENSION BAND UNIT
GE	1VCR5002X	N/A	FIP INDCATES PROPER MODE CAPSTAN FAILS TO RUN	CHECK Q2005
GE	1VCR5002X	N/A	POWER BUTTON INOPERATIVE-WILL NOT TURN OFF	CHECK D6049 (MAY CHECK OK IN CIRCUIT)
GE	1VCR5002X	N/A	UNIT POWERS UP NO PLAY FF REWIND	CHECK/REPLACE C6032
GE	1VCR5002X	N/A	SLUGGISH AUDIO;NOISE BARS IN PIX;WILL NOT ADJUST	CHECK THE CAPSTAN IC OR FLYWHEEL BEARINGS
GE	1VCR5002X	N/A	UNIT WILL NOT ALWAYS LOAD	CHECK 'C' RING WHICH HOLDS THE CAM GEAR IN PLACE
GE	1VCR5002X	N/A	GARBLED AUDIO IN LP AND SLP	CHECK IC4705,PINCH ROLLER,CLUTCH ASSY.;IDLER
GE	1VCR5002X	N/A	DD CYLND.SHUTS OFF AFTER LOADING IS FINAL	REPLACE D6054
GE	1VCR5002X	N/A	TAPE LOAD/UNLOAD SLUGGISH-LEAVE TAPE HANGING OUT	CHECK Q1013 AND D1022 FOR SHORTS OR OPENS
GE	1VCR5002X	N/A	WHILE PLAYING GOES INTO REVIEW	CHECK/REPLACE IC6001
GE	1VCR5002X	N/A	IMMEDIATELY SHUTS OFF WITH POWER UP OF UNIT	CHECK OR REPLACE IC7001,21011,21013
GE	1VCR5002X	N/A	PLAY ENGAGED,LOADS,COUNTER FAILS TO COUNT,STOPS	Q6020,D6022
GE	1VCR5002X	N/A	NO COLOR IN PLAYBACK LIGHT HORINZ. BAR BEHIND VI	CHECK C5 IN THE POWER SUPPLY
GE	1VCR5002X	N/A	VERY BRIGHT FIP	CHECK D1015 IN POWER SUPPLY
GE	1VCR5002X	N/A	INTERMITTENT COLOR SMEAR AND WHITE LINES IN PB	CHECK Q1009,Q1010 ESPECIALLY IF IC1001 IS SHORTED
GE	1VCR5002X	N/A	COMPLETELY DEAD	CHECK R1001,R1034,R1006 FOR OPEN CONDITIONS
GE	1VCR5002X	N/A	WON'T RECORD -- MANUAL OR OTR	CLEAN OR REPLACE ERASE PROTECT SWITCH
GE	1VCR5002X	N/A	LOADING MOTOR WILL NOT RUN ALL FUNCT INOPERABLE	CHECK Q6009
GE	1VCR5002X	N/A	INTERMITTENTLY SHUTS DOWN	CHECK FOR DEFECTIVE DD CYLINDER
GE	1VCR5002X	N/A	NO FIP DISPLAY	CHECK R1030
GE	1VCR5002X	N/A	FF/CUE WILL NOT RELEASE UNTIL STOP IS PRESSED	REPLACE IC2601
GE	1VCR5002X	N/A	WILL NOT REWIND OR FAST FORWARD - NO CAPSTAN OPERATIONS	CHECK/REPLACE Q2005
GE	1VCR5002X	N/A	NO VIDEO-TUNER LEDS AND CHANNEL CHANGE OK	CHECK R1023
GE	1VCR5002X	N/A	NO COLOR	ADJUST VCO,VXO--CHECK 3.58MHZ,4.2MHZ,629KHZ
GE	1VCR5002X	N/A	PLAYS 3 TO 4 SECONDS THEN GOES TO STOP	CHECK D6021 D6022 D6023 AND D6024 FOR LEAKY SHORTCOND
GE	1VCR5002X	N/A	ERRATIC FUNCTIONS	CHECK/CLEAN/REPLACE MODE SELECT SWITCH
GE	1VCR5002X	N/A	LOADS TAPE AROUND HEAD WHEN EITHER FF/REW PUSHED	REPLACE MODE SELECT SWITCH
GE	1VCR5011X	N/A	DROPOUTS IN AUDIO AND SOMETIMES VIDEO WHEN VIEWING A RECORDING - MAY TAKE MINUTES OR HOURS TO SHOW UP	CHECK/REPLACE INTERMITTENT ERASE PROTECT SWITCH
GE	1VCR6004	N/A	FAILURE TO PASS LEAKAGE CURRENT HOT CHECK	CHECK OR REPLACE C1005
GE	1VCR6004	N/A	NO EE OR VV VIDEO AUDIO OK	CHECK/REPLACE IC3101
GE	1VCR6004	N/A	DEAD WITH OPEN FUSE	CHECK D1001,Q1001,R1003
GE	1VCR6004	N/A	TRACKING ADJUSTMENTS	MOST ACCURATELY PERFORMED IN SP MODE.
GE	1VCR6004	N/A	NO COLOR IN PLAY BACK ONLY	REPLACE IC3502 ON THE HEAD AMP CBA
GE	1VCR6004	N/A	REDUCED CLOCK & DAY BRILLIANCE	CHECK R1215
GE	1VCR6004	N/A	PUSH PLAY AND TAPE GOES TO REWIND	CHECK/REPLACE END SENSORS
GE	1VCR6004	N/A	WILL NOT RECORD WHEN TIMER IS SET	CHECK/CLEAN ERASE PROTECT SWITCH CONTACTS
GE	1VCR6004	N/A	SNOWY PIX IN PLAYBACK ONLY AUDIO OK	CHECK Q3001
GE	1VCR6004	N/A	VIDEO FROM RF VIDEO OUTLOOKS SCRAMBLED	CHECK VIDEO SIGNAL ON BOTH SIDES OF C3014
GE	1VCR6004	N/A	NO POWER UP--FIP OK,POWER SUPPLY OK	CK PIN #16 OF IC6001 (4-5V)--IF LOW,CK C6009
GE	1VCR6004	N/A	POWER SUPPLY TICKS WHEN PLUGGED IN AND ALL SECONDARY VOLTAGES ARE LOW.	CHECK R1002 (680k) FOR OPEN
GE	1VCR6004	N/A	ALL MODES OPERATIONAL NO FIP DISPLAY	CHECK FILAMENT VOLT.MISSING CHECKPINS7&8 OF T1001
GE	1VCR6004	N/A	GARBLED AUDIO IN LP AND SLP	CHECK PINCH ROLLER,CLUTCH ASSY.;IDLER
GE	1VCR6004	N/A	EXCESSIVE WOW AND FLUTTER	CHECK/REPLACE C2004 (BREAKING DOWN UNDER LOAD OR HIGH ESR)
GE	1VCR6004	N/A	WON'T POWER UP--DRUM RUNS CONTINUOUSLY	REPLACE IC6001 (MN15846VRG)
GE	1VCR6004	N/A	WHEN PLAY IS PRESSED,VCR RUNS FOR 2-5 SECONDS THEN SHUTS OFF-NEVER SWITCHES FROM TUNER TO VCR-LOADING MOTOR RUNS ON	CHECK/REPLACE MODE SELECT SWITCH
GE	1VCR6004	N/A	WEAK AUDIO (PLAYBACK ONLY)	CHECK C4014
GE	1VCR6004	N/A	STARTS PLAYING THEN STOPS;COUNTER DOESN'T WORK	CHECK IC1551
GE	1VCR6004	N/A	WON'T RECORD -- MANUAL OR OTR	CLEAN OR REPLACE ERASE PROTECT SWITCH
GE	1VCR6004	N/A	UNIT TICKS WHEN PLUGGED IN NO FIP	R1039
GE	1VCR6004	N/A	DISTORTION OF CASSETTE TRAY SIDE PLATE	CHECK R6070 RC00043,PLOO144,IC6001
GE	1VCR6004	N/A	NO COLOR ON PLAYBACK OF PRE-RECORDED TAPES	CHECK/REPLACE IC8101 (MN6163)
GE	1VCR6004	N/A	TOP & BOTTOM 2' OF PIX. OK CENTER SNOWY	CHECK OR REPLACE IC8102
GE	1VCR6004	N/A	NO TRACKING CONTROL MAY LOCK IN BRIEFLY	CHECK/REPLACE IC2002
GE	1VCR6004	N/A	SQUEL FROM THE POWER SUPP WHEN PLUGGED IN	CHECK D1023
GE	1VCR6004	N/A	POWERS UP-LOADS TAPE-NO PLAY,REC,EJECT,FF,REW	REPLACE IC7501
GE	1VCR6004	N/A	NO COLOR	ADJUST VCO,VXO--CHECK 3.58MHZ,4.2MHZ,629KHZ
GE	1VCR6004	N/A	AFTER POWER IS APPLIED CAPSTAN SPINS FOR A FEW S	CHECK / REPLACE Q6003 IN MICROPROCESSOR CIRCUIT
GE	1VCR6004	N/A	INTERMITTENTLY STOPS PLAYING W/KNOWN GOOD TAPE	CHECK Q1552 (SUPPLY PHOTO XSTR)
GE	1VCR6004	N/A	PIX JITTERS ON SPECIAL EFFECTS	CHECK V-LOCK ADJUSTMENT-WORN HEADS-PG SHIFTERS TR.FIX
GE	1VCR6004	N/A	CAPSTAN MOTOR RUNS ABOUT 8SEC. THEN SHUTS DOWN	CHECK R6070
GE	1VCR6004	N/A	CAPSTAN MOTOR OSCILLATES BACK & FORTH	REPLACE IC2002
GE	1VCR6004	N/A	NO AUDIO	CHECK/REPLACE Q7010 & Q7002
GE	1VCR6004	N/A	AFTER POWER IS APPLIED CAPSTAN SPINS FORFEW SECS	CHECK/ REPLACE Q6003 IN MICROPROCESSOR CIRCUIT
GE	1VCR6004	N/A	NO AUTO STOP AT END OF TAPE IN PLAY FAST FOR REW	CHECK/REPLACE Q6008
GE	1VCR6010X	N/A	PUSH PLAY AND TAPE GOES TO REWIND	CHECK/REPLACE END SENSORS
GE	1VCR6010X	N/A	TRACKING ADJUSTMENTS	MOST ACCURATELY PERFORMED IN SP MODE.
GE	1VCR6010X	N/A	FAILURE TO PASS LEAKAGE CURRENT HOT CHECK	CHECK OR REPLACE C1005
GE	1VCR6010X	N/A	ALL MODES OPERATIONAL NO FIP DISPLAY	CHECK FILAMENT VOLT.MISSING CHECKPINS7&8 OF T1001
GE	1VCR6010X	N/A	WHEN PLAY IS PRESSED,VCR RUNS FOR 2-5 SECONDS THEN SHUTS OFF-NEVER SWITCHES FROM TUNER TO VCR-LOADING MOTOR RUNS ON	CHECK/REPLACE MODE SELECT SWITCH
GE	1VCR6010X	N/A	NO COLOR IN PLAY BACK ONLY	REPLACE IC3502 ON THE HEAD AMP CBA
GE	1VCR6010X	N/A	NO EE OR VV VIDEO AUDIO OK	CHECK/REPLACE IC3101
GE	1VCR6010X	N/A	NO COLOR ON PLAYBACK OF PRE-RECORDED TAPES	CHECK/REPLACE IC8101 (MN6163)
GE	1VCR6010X	N/A	SQUEL FROM THE POWER SUPP WHEN PLUGGED IN	CHECK D1023
GE	1VCR6010X	N/A	GARBLED AUDIO IN LP AND SLP	CHECK PINCH ROLLER,CLUTCH ASSY.;IDLER
GE	1VCR6010X	N/A	INTERMITTENTLY STOPS PLAYING W/KNOWN GOOD TAPE	CHECK Q1552 (SUPPLY PHOTO XSTR)
GE	1VCR6010X	N/A	CAPSTAN MOTOR RUNS ABOUT 8SEC. THEN SHUTS DOWN	CHECK R6070
GE	1VCR6010X	N/A	NO AUDIO	CHECK/REPLACE Q7010 & Q7002
GE	1VCR6010X	N/A	VIDEO FROM RF VIDEO OUTLOOKS SCRAMBLED	CHECK VIDEO SIGNAL ON BOTH SIDES OF C3014
GE	1VCR6010X	N/A	NO POWER UP--FIP OK,POWER SUPPLY OK	CK PIN #16 OF IC6001 (4-5V)--IF LOW,CK C6009
GE	1VCR6010X	N/A	DISTORTION OF CASSETTE TRAY SIDE PLATE	CHECK R6070 RC00043,PLOO144,IC6001
GE	1VCR6010X	N/A	POWER SUPPLY TICKS WHEN PLUGGED IN AND ALL SECONDARY VOLTAGES ARE LOW.	CHECK R1002 (680k) FOR OPEN
GE	1VCR6010X	N/A	POWERS UP-LOADS TAPE-NO PLAY,REC,EJECT,FF,REW	REPLACE IC7501
GE	1VCR6010X	N/A	EXCESSIVE WOW AND FLUTTER	CHECK/REPLACE C2004 (BREAKING DOWN UNDER LOAD OR HIGH ESR)
GE	1VCR6010X	N/A	NO TRACKING CONTROL MAY LOCK IN BRIEFLY	CHECK/REPLACE IC2002
GE	1VCR6010X	N/A	TOP & BOTTOM 2' OF PIX. OK CENTER SNOWY	CHECK OR REPLACE IC8102
GE	1VCR6010X	N/A	WON'T RECORD -- MANUAL OR OTR	CLEAN OR REPLACE ERASE PROTECT SWITCH
GE	1VCR6010X	N/A	WON'T POWER UP--DRUM RUNS CONTINUOUSLY	REPLACE IC6001 (MN15846VRG)
GE	1VCR6010X	N/A	REDUCED CLOCK & DAY BRILLIANCE	CHECK R1215
GE	1VCR6010X	N/A	NO COLOR	ADJUST VCO,VXO--CHECK 3.58MHZ,4.2MHZ,629KHZ
GE	1VCR6010X	N/A	SNOWY PIX IN PLAYBACK ONLY AUDIO OK	CHECK Q3001
GE	1VCR6010X	N/A	NO AUTO STOP AT END OF TAPE IN PLAY FAST FOR REW	CHECK/REPLACE Q6008
GE	1VCR6010X	N/A	WILL NOT RECORD WHEN TIMER IS SET	CHECK/CLEAN ERASE PROTECT SWITCH CONTACTS
GE	1VCR6010X	N/A	UNIT TICKS WHEN PLUGGED IN NO FIP	R1039
GE	1VCR6010X	N/A	STARTS PLAYING THEN STOPS;COUNTER DOESN'T WORK	CHECK IC1551
GE	1VCR6010X	N/A	CAPSTAN MOTOR OSCILLATES BACK & FORTH	REPLACE IC2002
GE	1VCR6010X	N/A	WEAK AUDIO (PLAYBACK ONLY)	CHECK C4014
GE	1VCR6010X	N/A	AFTER POWER IS APPLIED CAPSTAN SPINS FORFEW SECS	CHECK/ REPLACE Q6003 IN MICROPROCESSOR CIRCUIT
GE	1VCR6010X	N/A	AFTER POWER IS APPLIED CAPSTAN SPINS FOR A FEW S	CHECK / REPLACE Q6003 IN MICROPROCESSOR CIRCUIT
GE	1VCR6010X	N/A	DEAD WITH OPEN FUSE	CHECK D1001,Q1001,R1003
GE	1VCR6010X	N/A	PIX JITTERS ON SPECIAL EFFECTS	CHECK V-LOCK ADJUSTMENT-WORN HEADS-PG SHIFTERS TR.FIX
GE	1VCR6011X	N/A	NO AUTO STOP AT END OF TAPE IN PLAY FAST FOR REW	CHECK/REPLACE Q6008
GE	1VCR6011X	N/A	EXCESSIVE WOW AND FLUTTER	CHECK/REPLACE C2004 (BREAKING DOWN UNDER LOAD OR HIGH ESR)
GE	1VCR6011X	N/A	NO AUDIO	CHECK/REPLACE Q7010 & Q7002
GE	1VCR6011X	N/A	WON'T RECORD -- MANUAL OR OTR	CLEAN OR REPLACE ERASE PROTECT SWITCH
GE	1VCR6011X	N/A	SNOWY PIX IN PLAYBACK ONLY AUDIO OK	CHECK Q3001
GE	1VCR6011X	N/A	NO COLOR ON PLAYBACK OF PRE-RECORDED TAPES	CHECK/REPLACE IC8101 (MN6163)
GE	1VCR6011X	N/A	INTERMITTENTLY STOPS PLAYING W/KNOWN GOOD TAPE	CHECK Q1552 (SUPPLY PHOTO XSTR)
GE	1VCR6011X	N/A	NO COLOR IN PLAY BACK ONLY	REPLACE IC3502 ON THE HEAD AMP CBA
GE	1VCR6011X	N/A	TOP & BOTTOM 2' OF PIX. OK CENTER SNOWY	CHECK OR REPLACE IC8102
GE	1VCR6011X	N/A	CAPSTAN MOTOR RUNS ABOUT 8SEC. THEN SHUTS DOWN	CHECK R6070
GE	1VCR6011X	N/A	WEAK AUDIO (PLAYBACK ONLY)	CHECK C4014
GE	1VCR6011X	N/A	FAILURE TO PASS LEAKAGE CURRENT HOT CHECK	CHECK OR REPLACE C1005
GE	1VCR6011X	N/A	CAPSTAN MOTOR OSCILLATES BACK & FORTH	REPLACE IC2002
GE	1VCR6011X	N/A	DISTORTION OF CASSETTE TRAY SIDE PLATE	CHECK R6070 RC00043,PLOO144,IC6001
GE	1VCR6011X	N/A	GARBLED AUDIO IN LP AND SLP	CHECK PINCH ROLLER,CLUTCH ASSY.;IDLER
GE	1VCR6011X	N/A	POWERS UP-LOADS TAPE-NO PLAY,REC,EJECT,FF,REW	REPLACE IC7501
GE	1VCR6011X	N/A	ALL MODES OPERATIONAL NO FIP DISPLAY	CHECK FILAMENT VOLT.MISSING CHECKPINS7&8 OF T1001
GE	1VCR6011X	N/A	WILL NOT RECORD WHEN TIMER IS SET	CHECK/CLEAN ERASE PROTECT SWITCH CONTACTS
GE	1VCR6011X	N/A	WHEN PLAY IS PRESSED,VCR RUNS FOR 2-5 SECONDS THEN SHUTS OFF-NEVER SWITCHES FROM TUNER TO VCR-LOADING MOTOR RUNS ON	CHECK/REPLACE MODE SELECT SWITCH
GE	1VCR6011X	N/A	AFTER POWER IS APPLIED CAPSTAN SPINS FOR A FEW S	CHECK / REPLACE Q6003 IN MICROPROCESSOR CIRCUIT
GE	1VCR6011X	N/A	PIX JITTERS ON SPECIAL EFFECTS	CHECK V-LOCK ADJUSTMENT-WORN HEADS-PG SHIFTERS TR.FIX
GE	1VCR6011X	N/A	POWER SUPPLY TICKS WHEN PLUGGED IN AND ALL SECONDARY VOLTAGES ARE LOW.	CHECK R1002 (680k) FOR OPEN
GE	1VCR6011X	N/A	STARTS PLAYING THEN STOPS;COUNTER DOESN'T WORK	CHECK IC1551
GE	1VCR6011X	N/A	TRACKING ADJUSTMENTS	MOST ACCURATELY PERFORMED IN SP MODE.
GE	1VCR6011X	N/A	NO POWER UP--FIP OK,POWER SUPPLY OK	CK PIN #16 OF IC6001 (4-5V)--IF LOW,CK C6009
GE	1VCR6011X	N/A	VIDEO FROM RF VIDEO OUTLOOKS SCRAMBLED	CHECK VIDEO SIGNAL ON BOTH SIDES OF C3014
GE	1VCR6011X	N/A	DEAD WITH OPEN FUSE	CHECK D1001,Q1001,R1003
GE	1VCR6011X	N/A	REDUCED CLOCK & DAY BRILLIANCE	CHECK R1215
GE	1VCR6011X	N/A	NO COLOR	ADJUST VCO,VXO--CHECK 3.58MHZ,4.2MHZ,629KHZ
GE	1VCR6011X	N/A	NO TRACKING CONTROL MAY LOCK IN BRIEFLY	CHECK/REPLACE IC2002
GE	1VCR6011X	N/A	AFTER POWER IS APPLIED CAPSTAN SPINS FORFEW SECS	CHECK/ REPLACE Q6003 IN MICROPROCESSOR CIRCUIT
GE	1VCR6011X	N/A	NO EE OR VV VIDEO AUDIO OK	CHECK/REPLACE IC3101
GE	1VCR6011X	N/A	SQUEL FROM THE POWER SUPP WHEN PLUGGED IN	CHECK D1023
GE	1VCR6011X	N/A	UNIT TICKS WHEN PLUGGED IN NO FIP	R1039
GE	1VCR6011X	N/A	WON'T POWER UP--DRUM RUNS CONTINUOUSLY	REPLACE IC6001 (MN15846VRG)
GE	1VCR6011X	N/A	PUSH PLAY AND TAPE GOES TO REWIND	CHECK/REPLACE END SENSORS
GE	1VCR6013	N/A	DISTORTION OF CASSETTE TRAY SIDE PLATE	CHECK R6070 RC00043,PLOO144,IC6001
GE	1VCR6013	N/A	REDUCED CLOCK & DAY BRILLIANCE	CHECK R1215
GE	1VCR6013	N/A	PUSH PLAY AND TAPE GOES TO REWIND	CHECK/REPLACE END SENSORS
GE	1VCR6013	N/A	SQUEL FROM THE POWER SUPP WHEN PLUGGED IN	CHECK D1023
GE	1VCR6013	N/A	GARBLED AUDIO IN LP AND SLP	CHECK PINCH ROLLER,CLUTCH ASSY.;IDLER
GE	1VCR6013	N/A	NO COLOR IN PLAY BACK ONLY	REPLACE IC3502 ON THE HEAD AMP CBA
GE	1VCR6013	N/A	AFTER POWER IS APPLIED CAPSTAN SPINS FOR A FEW S	CHECK / REPLACE Q6003 IN MICROPROCESSOR CIRCUIT
GE	1VCR6013	N/A	INTERMITTENTLY STOPS PLAYING W/KNOWN GOOD TAPE	CHECK Q1552 (SUPPLY PHOTO XSTR)
GE	1VCR6013	N/A	POWER SUPPLY TICKS WHEN PLUGGED IN AND ALL SECONDARY VOLTAGES ARE LOW.	CHECK R1002 (680k) FOR OPEN
GE	1VCR6013	N/A	UNIT TICKS WHEN PLUGGED IN NO FIP	R1039
GE	1VCR6013	N/A	CAPSTAN MOTOR RUNS ABOUT 8SEC. THEN SHUTS DOWN	CHECK R6070
GE	1VCR6013	N/A	TOP & BOTTOM 2' OF PIX. OK CENTER SNOWY	CHECK OR REPLACE IC8102
GE	1VCR6013	N/A	POWERS UP-LOADS TAPE-NO PLAY,REC,EJECT,FF,REW	REPLACE IC7501
GE	1VCR6013	N/A	CAPSTAN MOTOR OSCILLATES BACK & FORTH	REPLACE IC2002
GE	1VCR6013	N/A	NO COLOR	ADJUST VCO,VXO--CHECK 3.58MHZ,4.2MHZ,629KHZ
GE	1VCR6013	N/A	WEAK AUDIO (PLAYBACK ONLY)	CHECK C4014
GE	1VCR6013	N/A	SNOWY PIX IN PLAYBACK ONLY AUDIO OK	CHECK Q3001
GE	1VCR6013	N/A	NO POWER UP--FIP OK,POWER SUPPLY OK	CK PIN #16 OF IC6001 (4-5V)--IF LOW,CK C6009
GE	1VCR6013	N/A	STARTS PLAYING THEN STOPS;COUNTER DOESN'T WORK	CHECK IC1551
GE	1VCR6013	N/A	VIDEO FROM RF VIDEO OUTLOOKS SCRAMBLED	CHECK VIDEO SIGNAL ON BOTH SIDES OF C3014
GE	1VCR6013	N/A	WILL NOT RECORD WHEN TIMER IS SET	CHECK/CLEAN ERASE PROTECT SWITCH CONTACTS
GE	1VCR6013	N/A	TRACKING ADJUSTMENTS	MOST ACCURATELY PERFORMED IN SP MODE.
GE	1VCR6013	N/A	NO EE OR VV VIDEO AUDIO OK	CHECK/REPLACE IC3101
GE	1VCR6013	N/A	AFTER POWER IS APPLIED CAPSTAN SPINS FORFEW SECS	CHECK/ REPLACE Q6003 IN MICROPROCESSOR CIRCUIT
GE	1VCR6013	N/A	WON'T POWER UP--DRUM RUNS CONTINUOUSLY	REPLACE IC6001 (MN15846VRG)
GE	1VCR6013	N/A	ALL MODES OPERATIONAL NO FIP DISPLAY	CHECK FILAMENT VOLT.MISSING CHECKPINS7&8 OF T1001
GE	1VCR6013	N/A	NO TRACKING CONTROL MAY LOCK IN BRIEFLY	CHECK/REPLACE IC2002
GE	1VCR6013	N/A	EXCESSIVE WOW AND FLUTTER	CHECK/REPLACE C2004 (BREAKING DOWN UNDER LOAD OR HIGH ESR)
GE	1VCR6013	N/A	DEAD WITH OPEN FUSE	CHECK D1001,Q1001,R1003
GE	1VCR6013	N/A	WON'T RECORD -- MANUAL OR OTR	CLEAN OR REPLACE ERASE PROTECT SWITCH
GE	1VCR6013	N/A	NO AUDIO	CHECK/REPLACE Q7010 & Q7002
GE	1VCR6013	N/A	PIX JITTERS ON SPECIAL EFFECTS	CHECK V-LOCK ADJUSTMENT-WORN HEADS-PG SHIFTERS TR.FIX
GE	1VCR6013	N/A	WHEN PLAY IS PRESSED,VCR RUNS FOR 2-5 SECONDS THEN SHUTS OFF-NEVER SWITCHES FROM TUNER TO VCR-LOADING MOTOR RUNS ON	CHECK/REPLACE MODE SELECT SWITCH
GE	1VCR6013	N/A	FAILURE TO PASS LEAKAGE CURRENT HOT CHECK	CHECK OR REPLACE C1005
GE	1VCR6013	N/A	NO AUTO STOP AT END OF TAPE IN PLAY FAST FOR REW	CHECK/REPLACE Q6008
GE	1VCR6013	N/A	NO COLOR ON PLAYBACK OF PRE-RECORDED TAPES	CHECK/REPLACE IC8101 (MN6163)
GE	97100	N/A	DEW INDICATOR ILLUMINATES AND UNIT SHUTS DOWN	LOOSE CONNECTIONS ONTHE P3 PLUG
GE	97100	N/A	GARBLED AUDIO IN LP AND SLP	CHECK PINCH ROLLER,CLUTCH ASSY.;IDLER
GE	97100	N/A	CAPSTAN AND DRUM MOTORS WILL NOT RUN	CHECK FOR OPEN PR1 ON CAPSTAN/DRUM MOTOR DRIVE CBA
GE	97100	N/A	DEAD WITH OPEN FUSE	CHECK D1001,Q1001,R1003
GE	97100	N/A	DEAD	CHECK/REPLACE Q1001 AND IC1001
GE	97100	N/A	LOADING MOTOR SLOW OR SLUGGISH	CHECK/REPLACE C1015 OR C1016
GE	97100	N/A	DEAD	CHECK/REPLACE D1014 AND D1010 (MAY CHECK GOOD)
GE	97100	N/A	PIX JITTERS ON SPECIAL EFFECTS	CHECK V-LOCK ADJUSTMENT-WORN HEADS-PG SHIFTERS TR.FIX
GE	97100	N/A	WON'T RECORD -- MANUAL OR OTR	CLEAN OR REPLACE ERASE PROTECT SWITCH
GE	97100	N/A	NO PLAYBACK VIDEO AND APPEARS THAT HEADS ARE DIRTY	CHECK/REPLACE C3003 FOR SHORT
GE	97100	N/A	NO PICTURE THRU THE TUNER BUT PLAYS TAPE OK	CHECK/REPLACE IC7001
GE	97100	N/A	NO AUDIO FROM TUNER-PLAYBACK AUDIO OK	REPL. IC4001
GE	97100	N/A	QUITS PLAYING & SQUELS FROM POWER SUPPLY	CHECK/REPLACE FILTER CAP C1006
GE	97100	N/A	NO DRUM/NO CAPSTAN	CHECK PR1 (CIRCUIT PROTECTOR) MOTOR DRIVE BOARD
GE	97100	N/A	POOR CAPSTAN SPEED OR AUDIO QUIVER ON SP AND CAPSTAN PULSATES BACK AND FORTH ON LP AND SLP	CHECK/REPLACE C1015,C1016,C1018 AND C1019 IN POWER SUPPLY
GE	97100	N/A	HORZ LINES-DRUM MOTOR RUNNING TOO FAST	REPLACE DD CYL. MOTOR
GE	97100	N/A	NO FIP LOADING MOTOR ENGAGES OK	CHECK/REPLACE C1020 C1021 L1005
GE	97100	N/A	COLOR FADES IN AND OUT	CHECK/REPLACE UPPER CYLINDER UNIT
GE	97100	N/A	TRACKING ADJUSTMENTS	MOST ACCURATELY PERFORMED IN SP MODE.
GE	97100	N/A	NO COLOR	ADJUST VCO,VXO--CHECK 3.58MHZ,4.2MHZ,629KHZ
GE	97100	N/A	UNIT ACCEPTS TAPE BUT NO OTHER FUNCTIONS WILL WORK	CHECK/REPLACE LED SENSOR LAMP UNIT
GE	97100	N/A	WOW & FLUTTER MOSTLY IN SLP SPEED	CHECK/REPLACE PINCH ROLLER
GE	97100	N/A	VCR DOESN'T ERASE OLD AUDIO	CHECK/REPLACE C4023
GE	97100	N/A	PICTURE GETS DARKER OR LIGHTER ON PLAYBACK ONLY AND MAY ALSO LOSE COLOR	CHECK/RESOLDER GROUND CONNECTIONS ON R3122
GE	97100	N/A	NO PICTURE DURING PLAYBACK-ONLY GREY SCREEN	CHECK/REPLACE C3009 FOR SHORT
GE	97100	N/A	DRUM SERVO SPEED IS TOO FAST-SLOWING DRUM DOWN BY HAND WILL CAUSE A PICTURE TO APPEAR.	CHECK C2010 AND C2011 FOR LEAKAGE/OPEN/SHORT
GE	97120	N/A	NO VV OR EE VIDEO AUDIO OK BOTH MODES	CHECK FOR OPEN L3101 COIL
GE	97120	N/A	TRACKING ADJUSTMENTS	MOST ACCURATELY PERFORMED IN SP MODE.
GE	97120	N/A	TUNER VIDEO PRESENT WHILE PLAYING TAPE	REPLACE IC3101
GE	97120	N/A	TUNES CHANNELS MANUALLY BUT WON'T HOLD CHANNEL MEMORY	CHECK/REPLACE IC7603
GE	97120	N/A	NO PICTURE THRU THE TUNER BUT PLAYS TAPE OK	CHECK/REPLACE IC7001
GE	97120	N/A	UNIT ACCEPTS TAPE BUT NO OTHER FUNCTIONS WILL WORK	CHECK/REPLACE LED SENSOR LAMP UNIT
GE	97120	N/A	NO DRUM/NO CAPSTAN	CHECK PR1 (CIRCUIT PROTECTOR) MOTOR DRIVE BOARD
GE	97120	N/A	DEAD	CHECK/REPLACE Q1001 AND IC1001
GE	97120	N/A	CAPSTAN AND DRUM MOTORS WILL NOT RUN	CHECK FOR OPEN PR1 ON CAPSTAN/DRUM MOTOR DRIVE CBA
GE	97120	N/A	VCR DOESN'T ERASE OLD AUDIO	CHECK/REPLACE C4023
GE	97120	N/A	WON'T RECORD -- MANUAL OR OTR	CLEAN OR REPLACE ERASE PROTECT SWITCH
GE	97120	N/A	WILL NOT LOAD CARRIAGE MOTOR OR TAPE TRANSPORT MOTOR - POWER SHUTS OFF AFTER 5 SECONDS	CHECK/REPLACE Q1203 FOR SHORT
GE	97120	N/A	WOW & FLUTTER MOSTLY IN SLP SPEED	CHECK/REPLACE PINCH ROLLER
GE	97120	N/A	PIX JITTERS ON SPECIAL EFFECTS	CHECK V-LOCK ADJUSTMENT-WORN HEADS-PG SHIFTERS TR.FIX
GE	97120	N/A	WARBLE IN THE AUDIO ON ALL SPEEDS AND SOME COLOR FLASHING IN/OUT	CHECK/REPLACE C1015,C1016,C1018 AND C1019 FOR OPEN
GE	97120	N/A	DEAD	CHECK/REPLACE D1014 AND D1010 (MAY CHECK GOOD)
GE	97120	N/A	CASSETTE LOADS OK DD CYLINDER STARTS	REPLACE IC2001
GE	97120	N/A	PICTURE GETS DARKER OR LIGHTER ON PLAYBACK ONLY AND MAY ALSO LOSE COLOR	CHECK/RESOLDER GROUND CONNECTIONS ON R3122
GE	97120	N/A	COLOR FADES IN AND OUT	CHECK/REPLACE UPPER CYLINDER UNIT
GE	97120	N/A	NO AUDIO FROM TUNER-PLAYBACK AUDIO OK	REPL. IC4001
GE	97120	N/A	NO VIDEO IN VCR MODE AUDIO OK LOSS OF VIDEO Bt.	CHECK AND OR REPLACE L3101
GE	97120	N/A	NO PICTURE DURING PLAYBACK-ONLY GREY SCREEN	CHECK/REPLACE C3009 FOR SHORT
GE	97120	N/A	NO VIDEO - LOOKS LIKE A BAD VIDEO HEAD - AUDIO IS NORMAL	CHECK/REPLACE C3009 FOR SHORT
GE	97120	N/A	INT. GOOD PIX. / SNOW IN PLAYBACK	CHECK IC2003
GE	97120	N/A	NO PLAYBACK VIDEO AND APPEARS THAT HEADS ARE DIRTY	CHECK/REPLACE C3003 FOR SHORT
GE	97120	N/A	DRUM SERVO SPEED IS TOO FAST-SLOWING DRUM DOWN BY HAND WILL CAUSE A PICTURE TO APPEAR.	CHECK C2010 AND C2011 FOR LEAKAGE/OPEN/SHORT
GE	97120	N/A	LOADING MOTOR SLOW OR SLUGGISH	CHECK/REPLACE C1015 OR C1016
GE	97120	N/A	QUITS PLAYING & SQUELS FROM POWER SUPPLY	CHECK/REPLACE FILTER CAP C1006
GE	97120	N/A	SNOWY PIX-TUNING DRIFTS-MAY IMPROVE AFTER WARM	CHECK IC701
GE	97120	N/A	NO COLOR	ADJUST VCO,VXO--CHECK 3.58MHZ,4.2MHZ,629KHZ
GE	97120	N/A	HORZ LINES-DRUM MOTOR RUNNING TOO FAST	REPLACE DD CYL. MOTOR
GE	97120	N/A	GARBLED AUDIO IN LP AND SLP	CHECK PINCH ROLLER AND CLUTCH ASSY OR IDLER
GE	97120	N/A	DEAD WITH OPEN FUSE	CHECK D1001,Q1001,R1003
GE	97120	N/A	POOR CAPSTAN SPEED OR AUDIO QUIVER ON SP AND CAPSTAN PULSATES BACK AND FORTH ON LP AND SLP	CHECK/REPLACE C1015,C1016,C1018 AND C1019 IN POWER SUPPLY
GE	97120	N/A	NO VIDEO IN TUNER MODE WITH RF INPUT AUDIO OK	CHECK D4401 OR D4052
GE	97135	N/A	NO PICTURE DURING PLAYBACK-ONLY GREY SCREEN	CHECK/REPLACE C3009 FOR SHORT
GE	97135	N/A	DEAD	CHECK/REPLACE D1014 AND D1010 (MAY CHECK GOOD)
GE	97135	N/A	DEAD WITH OPEN FUSE	CHECK D1001,Q1001,R1003
GE	97135	N/A	LOADING MOTOR SLOW OR SLUGGISH	CHECK/REPLACE C1015 OR C1016
GE	97135	N/A	GARBLED AUDIO IN LP AND SLP	CHECK PINCH ROLLER,CLUTCH ASSY.;IDLER
GE	97135	N/A	NO PLAYBACK VIDEO AND APPEARS THAT HEADS ARE DIRTY	CHECK/REPLACE C3003 FOR SHORT
GE	97135	N/A	NO AUDIO FROM TUNER-PLAYBACK AUDIO OK	REPL. IC4001
GE	97135	N/A	DEAD	CHECK/REPLACE Q1001 AND IC1001
GE	97135	N/A	NO DRUM LOCK - PIX HAS HORZ. LINES	CHECK/REPLACE C2010 AND C2011 FOR LEAKAGE OR A CHANGE IN VALUE.
GE	97135	N/A	HORZ LINES-DRUM MOTOR RUNNING TOO FAST	REPLACE DD CYL. MOTOR
GE	97135	N/A	NO PICTURE THRU THE TUNER BUT PLAYS TAPE OK	CHECK/REPLACE IC7001
GE	97135	N/A	NO VIDEO - LOOKS LIKE A BAD VIDEO HEAD - AUDIO IS NORMAL	CHECK/REPLACE C3009 FOR SHORT
GE	97135	N/A	CAPSTAN AND DRUM MOTORS WILL NOT RUN	CHECK FOR OPEN PR1 ON CAPSTAN/DRUM MOTOR DRIVE CBA
GE	97135	N/A	NO DRUM/NO CAPSTAN	CHECK PR1 (CIRCUIT PROTECTOR) MOTOR DRIVE BOARD
GE	97135	N/A	PIX JITTERS ON SPECIAL EFFECTS	CHECK V-LOCK ADJUSTMENT-WORN HEADS-PG SHIFTERS TR.FIX
GE	97135	N/A	DD CYL. MOTOR ROTATES VERY SLOW/ROTATE BACK FORT	CHECK OR REPLACE THE DD CYL.
GE	97135	N/A	WON'T RECORD -- MANUAL OR OTR	CLEAN OR REPLACE ERASE PROTECT SWITCH
GE	97135	N/A	NO COLOR	ADJUST VCO,VXO--CHECK 3.58MHZ,4.2MHZ,629KHZ
GE	97135	N/A	VCR DOESN'T ERASE OLD AUDIO	CHECK/REPLACE C4023
GE	97135	N/A	POOR CAPSTAN SPEED OR AUDIO QUIVER ON SP AND CAPSTAN PULSATES BACK AND FORTH ON LP AND SLP	CHECK/REPLACE C1015,C1016,C1018 AND C1019 IN POWER SUPPLY
GE	97135	N/A	UNIT ACCEPTS TAPE BUT NO OTHER FUNCTIONS WILL WORK	CHECK/REPLACE LED SENSOR LAMP UNIT
GE	97135	N/A	WOW & FLUTTER MOSTLY IN SLP SPEED	CHECK/REPLACE PINCH ROLLER
GE	97135	N/A	COLOR FADES IN AND OUT	CHECK/REPLACE UPPER CYLINDER UNIT
GE	97135	N/A	PICTURE GETS DARKER OR LIGHTER ON PLAYBACK ONLY AND MAY ALSO LOSE COLOR	CHECK/RESOLDER GROUND CONNECTIONS ON R3122
GE	97135	N/A	TRACKING ADJUSTMENTS	MOST ACCURATELY PERFORMED IN SP MODE.
GE	97135	N/A	NO DRUM LOCK - PIX HAS HORZ. LINES	CHECK/REPLACE C2010 AND C2011 FOR LEAKAGE OR A CHANGE IN VALUE.
GE	97140	N/A	UNIT ACCEPTS TAPE BUT NO OTHER FUNCTIONS WILL WORK	CHECK/REPLACE LED SENSOR LAMP UNIT
GE	97140	N/A	NO AUDIO FROM TUNER-PLAYBACK AUDIO OK	REPL. IC4001
GE	97140	N/A	TRACKING ADJUSTMENTS	MOST ACCURATELY PERFORMED IN SP MODE.
GE	97140	N/A	NO DRUM LOCK - PIX HAS HORZ. LINES	CHECK/REPLACE C2010 AND C2011 FOR LEAKAGE OR A CHANGE IN VALUE.
GE	97140	N/A	PIX JITTERS ON SPECIAL EFFECTS	CHECK V-LOCK ADJUSTMENT-WORN HEADS-PG SHIFTERS TR.FIX
GE	97140	N/A	WOW & FLUTTER MOSTLY IN SLP SPEED	CHECK/REPLACE PINCH ROLLER
GE	97140	N/A	TUNES CHANNELS MANUALLY BUT WON'T HOLD CHANNEL MEMORY	CHECK/REPLACE IC7603
GE	97140	N/A	WARBLE IN THE AUDIO ON ALL SPEEDS AND SOME COLOR FLASHING IN/OUT	CHECK/REPLACE C1015,C1016,C1018 AND C1019 FOR OPEN
GE	97140	N/A	COLOR FADES IN AND OUT	CHECK/REPLACE UPPER CYLINDER UNIT
GE	97140	N/A	WON'T RECORD -- MANUAL OR OTR	CLEAN OR REPLACE ERASE PROTECT SWITCH
GE	97140	N/A	NO PICTURE THRU THE TUNER BUT PLAYS TAPE OK	CHECK/REPLACE IC7001
GE	97140	N/A	POOR CAPSTAN SPEED OR AUDIO QUIVER ON SP AND CAPSTAN PULSATES BACK AND FORTH ON LP AND SLP	CHECK/REPLACE C1015,C1016,C1018 AND C1019 IN POWER SUPPLY
GE	97140	N/A	NO DRUM/NO CAPSTAN	CHECK PR1 (CIRCUIT PROTECTOR) MOTOR DRIVE BOARD
GE	97140	N/A	CAPSTAN AND DRUM MOTORS WILL NOT RUN	CHECK FOR OPEN PR1 ON CAPSTAN/DRUM MOTOR DRIVE CBA
GE	97140	N/A	PICTURE GETS DARKER OR LIGHTER ON PLAYBACK ONLY AND MAY ALSO LOSE COLOR	CHECK/RESOLDER GROUND CONNECTIONS ON R3122
GE	97140	N/A	LOADING MOTOR SLOW OR SLUGGISH	CHECK/REPLACE C1015 OR C1016
GE	97140	N/A	VCR DOESN'T ERASE OLD AUDIO	CHECK/REPLACE C4023
GE	97140	N/A	DEAD	CHECK/REPLACE D1014 AND D1010 (MAY CHECK GOOD)
GE	97140	N/A	GARBLED AUDIO IN LP AND SLP	CHECK PINCH ROLLER,CLUTCH ASSY.;IDLER
GE	97140	N/A	NO PICTURE DURING PLAYBACK-ONLY GREY SCREEN	CHECK/REPLACE C3009 FOR SHORT
GE	97140	N/A	NO DRUM LOCK - PIX HAS HORZ. LINES	CHECK/REPLACE C2010 AND C2011 FOR LEAKAGE OR A CHANGE IN VALUE.
GE	97140	N/A	DEAD	CHECK/REPLACE Q1001 AND IC1001
GE	97140	N/A	NO VIDEO - LOOKS LIKE A BAD VIDEO HEAD - AUDIO IS NORMAL	CHECK/REPLACE C3009 FOR SHORT
GE	97140	N/A	HORZ LINES-DRUM MOTOR RUNNING TOO FAST	REPLACE DD CYL. MOTOR
GE	97140	N/A	DD CYL. MOTOR ROTATES VERY SLOW/ROTATE BACK FORT	CHECK OR REPLACE THE DD CYL.
GE	97140	N/A	NO PLAYBACK VIDEO AND APPEARS THAT HEADS ARE DIRTY	CHECK/REPLACE C3003 FOR SHORT
GE	97140	N/A	NO COLOR	ADJUST VCO,VXO--CHECK 3.58MHZ,4.2MHZ,629KHZ
GE	97140	N/A	DEAD WITH OPEN FUSE	CHECK D1001,Q1001,R1003
GE	97175	N/A	LOADING MOTOR SLOW OR SLUGGISH	CHECK/REPLACE C1015 OR C1016
GE	97175	N/A	NO VIDEO IN TUNER MODE WITH RF INPUT AUDIO OK	CHECK D4401 OR D4052
GE	97175	N/A	UNIT ACCEPTS TAPE BUT NO OTHER FUNCTIONS WILL WORK	CHECK/REPLACE LED SENSOR LAMP UNIT
GE	97175	N/A	DEAD	CHECK/REPLACE D1014 AND D1010 (MAY CHECK GOOD)
GE	97175	N/A	NO FIP NO CHANNEL CHANGE	CHECK/ REPLACE R1211
GE	97175	N/A	POOR CAPSTAN SPEED OR AUDIO QUIVER ON SP AND CAPSTAN PULSATES BACK AND FORTH ON LP AND SLP	CHECK/REPLACE C1015,C1016,C1018 AND C1019 IN POWER SUPPLY
GE	97175	N/A	PIX JITTERS ON SPECIAL EFFECTS	CHECK V-LOCK ADJUSTMENT-WORN HEADS-PG SHIFTERS TR.FIX
GE	97175	N/A	WILL NOT LOAD CARRIAGE MOTOR OR TAPE TRANSPORT MOTOR - POWER SHUTS OFF AFTER 5 SECONDS	CHECK/REPLACE Q1203 FOR SHORT
GE	97175	N/A	CAPSTAN AND DRUM MOTORS WILL NOT RUN	CHECK FOR OPEN PR1 ON CAPSTAN/DRUM MOTOR DRIVE CBA
GE	97175	N/A	VCR DOESN'T ERASE OLD AUDIO	CHECK/REPLACE C4023
GE	97175	N/A	DEAD	CHECK/REPLACE Q1001 AND IC1001
GE	97175	N/A	TUNES CHANNELS MANUALLY BUT WON'T HOLD CHANNEL MEMORY	CHECK/REPLACE IC7603
GE	97175	N/A	NO PAUSE,CUE OR REVIEW;PLAY AND RECORD IS OK	CHECK R2031 AND Q3005
GE	97175	N/A	NO PLAYBACK VIDEO AND APPEARS THAT HEADS ARE DIRTY	CHECK/REPLACE C3003 FOR SHORT
GE	97175	N/A	NO PICTURE DURING PLAYBACK-ONLY GREY SCREEN	CHECK/REPLACE C3009 FOR SHORT
GE	97175	N/A	NO VIDEO - LOOKS LIKE A BAD VIDEO HEAD - AUDIO IS NORMAL	CHECK/REPLACE C3009 FOR SHORT
GE	97175	N/A	PICTURE GETS DARKER OR LIGHTER ON PLAYBACK ONLY AND MAY ALSO LOSE COLOR	CHECK/RESOLDER GROUND CONNECTIONS ON R3122
GE	97175	N/A	DRUM SERVO SPEED IS TOO FAST-SLOWING DRUM DOWN BY HAND WILL CAUSE A PICTURE TO APPEAR.	CHECK C2010 AND C2011 FOR LEAKAGE/OPEN/SHORT
GE	97175	N/A	COLOR FADES IN AND OUT	CHECK/REPLACE UPPER CYLINDER UNIT
GE	97175	N/A	QUITS PLAYING & SQUELS FROM POWER SUPPLY	CHECK/REPLACE FILTER CAP C1006
GE	97175	N/A	CASSETTE LOADS OK DD CYLINDER STARTS	REPLACE IC2001
GE	97175	N/A	NO PICTURE THRU THE TUNER BUT PLAYS TAPE OK	CHECK/REPLACE IC7001
GE	97250	N/A	NO DRUM/NO CAPSTAN	CHECK PR1 (CIRCUIT PROTECTOR) MOTOR DRIVE BOARD
GE	97250	N/A	NO VIDEO IN TUNER MODE WITH RF INPUT AUDIO OK	CHECK D4401 OR D4052
GE	97250	N/A	WILL NOT LOAD CARRIAGE MOTOR OR TAPE TRANSPORT MOTOR - POWER SHUTS OFF AFTER 5 SECONDS	CHECK/REPLACE Q1203 FOR SHORT
GE	97250	N/A	DEAD WITH OPEN FUSE	CHECK D1001,Q1001,R1003
GE	97250	N/A	DRUM SERVO SPEED IS TOO FAST-SLOWING DRUM DOWN BY HAND WILL CAUSE A PICTURE TO APPEAR.	CHECK C2010 AND C2011 FOR LEAKAGE/OPEN/SHORT
GE	97250	N/A	CASSETTE LOADS OK DD CYLINDER STARTS	REPLACE IC2001
GE	97250	N/A	CASSETTE LOADS OK UNIT WILL NOT TURN ON	CHECK IC6001
GE	97250	N/A	NO AUDIO FROM TUNER-PLAYBACK AUDIO OK	REPL. IC4001
GE	97250	N/A	HORZ LINES-DRUM MOTOR RUNNING TOO FAST	REPLACE DD CYL. MOTOR
GE	97250	N/A	TUNES CHANNELS MANUALLY BUT WON'T HOLD CHANNEL MEMORY	CHECK/REPLACE IC7603
GE	97250	N/A	INT. GOOD PIX. / SNOW IN PLAYBACK	CHECK IC2003
GE	97250	N/A	WOW & FLUTTER MOSTLY IN SLP SPEED	CHECK/REPLACE PINCH ROLLER
GE	97250	N/A	LOADING MOTOR SLOW OR SLUGGISH	CHECK/REPLACE C1015 OR C1016
GE	97250	N/A	POWER BUTTON INOPERATIVE AFTER WARM UP	CHECK/REPLACE R7639
GE	97250	N/A	NO VIDEO - LOOKS LIKE A BAD VIDEO HEAD - AUDIO IS NORMAL	CHECK/REPLACE C3009 FOR SHORT
GE	97250	N/A	POOR CAPSTAN SPEED OR AUDIO QUIVER ON SP AND CAPSTAN PULSATES BACK AND FORTH ON LP AND SLP	CHECK/REPLACE C1015,C1016,C1018 AND C1019 IN POWER SUPPLY
GE	97250	N/A	QUITS PLAYING & SQUELS FROM POWER SUPPLY	CHECK/REPLACE FILTER CAP C1006
GE	97250	N/A	CAPSTAN AND DRUM MOTORS WILL NOT RUN	CHECK FOR OPEN PR1 ON CAPSTAN/DRUM MOTOR DRIVE CBA
GE	97450	N/A	TV CHANNEL DRIFTS INTERMITTENTLY	CHECK FL405 (VIDEO DETECT) NEAR IC401 PIN #13
GE	97515	N/A	INSERT TAPE,MACHINE LOADS TAPE AROUND HEADS BUT NO MOTORS ARE RUNNING,THEN UNLOADS LEAVING TAPE HANGING FROM TAPE.	CHECK/CLEAN MODE SELECT SWITCH
GE	97515	N/A	GARBLED AUDIO	CHECK Q0501,R0501,C0502,L0501
GE	97515	N/A	SHUTS OFF ON RECORD INTERMITTENT-SOMETIMES VCR WILL KICK THE TAPE OUT.	CHECK/CLEAN THE ERASE PROTECT SWITCH
GE	97515	N/A	NOISY VIDEO,NOISE BANDS OR STREAKS IN PLAYBACK VIDEO	REMOVE VIDEO HEAD AND INSTALL (2) LOCK WASHERS (210807) ON SCREWS LOCATED UNDER DRUM.
GE	97515	N/A	AUDIO MISSING IN PLAYBACK--NOT ERASING OLD AUDIO	CHECK IC601
GE	97515	N/A	NO VIDEO BUT OSD WORKS NORMALLY	CHECK C317 FOR LEAKAGE
GE	97515	N/A	CAPSTAN HAS INTERMITTENT SPEED CONTROL	CHECK/RESOLDER CONNECTIONS ON PATH BETWEEN IC601 PIN 26 AND R611
GE	97515	N/A	FRONT PANEL LOCKS UP - LOSS OF REMOTE OPERATION - MAY BE INTERMITTENT.	CHECK IC0601-IF THE TYPE NUMBER IS NOT UPD75116CW-091 THEN REPLACE WITH 195143-CHECK ALSO IR RECVR.192280
GE	97520	N/A	GARBLED AUDIO-TUNER AUDIO NOT SWITCHING ON P.B.	REPLACE IC4001
GE	97520	N/A	SUPPLY REELS START TURNING AS SOON AS UNIT IS PLUGGED IN BUT WILL NOT STAY ON - WILL NOT LOAD CASSETTE	CHECK/REPLACE R1010,D1008 AND C1011
GE	97520	N/A	DD CYLINDER RUNS FOR ABOUT 1 MINUTE - CHANNEL NUMBERS CHANGE BUT RECEIVES ONLY SNOW	CHECK/REPLACE D1008 AND R1010
GE	97520	N/A	WHEN UNIT IS PLUGGED IN,CAPSTAN RUNS 4-5 SECONDS AND SHUTS DOWN.	CHECK/REPLACE D1008 AND R1010
GE	97520	N/A	CAPSTAN MOTOR FLIP FLOPS BACK AND FORTH	CHECK IC8101
GE	97520	N/A	CAPSTAN SPINS THEN POWER SHUTS OFF (AT POWER UP)	CHECK IC6001 AND IC6002
GE	97520	N/A	CAPSTAN SPINS A FEW TIMES THEN UNIT SHUTS DOWN	CHECK /REPLACE R1010 Q606
GE	97520	N/A	TRACKING PROBLEMS IN SP MODE AND 'DONALD DUCK' IN LP AND SLP MODES	CHECK/REPLACE C2023 FOR SHORT
GE	97520	N/A	DEAD SET AND SHORT ON THE 5 VOLT LINE	CHECK/REPLACE C3137 AND PR1001
GE	97520	N/A	TV/VCR FUNCTIONS DOESN'T WORK BUT INDICATOR DOES LIGHT IN THE FIP DISPLAY	CHECK/REPLACE IC7601
GE	97520	N/A	ONE TICK FROM POWER SUPPLY-NO DISPLAY-NO POWER	CHECK PR1001,L1003,D1011,C1015 AND C1016
GE	97520	N/A	INTERMITTENT LOW NO AUDIO IN E/E PLAYBACK AUD,OK	REPLACE IC4001
GE	97520	N/A	SUPPLY REEL STARTS TURNING WHEN UNIT IS PLUGGED	CHECK/REPLACE R1010 D1008 C1011
GE	97520	N/A	DRUM MOTOR WILL NOT RUN	CHECK/REPLACE IC2603
GE	97520	N/A	WOW & FLUTTER MOSTLY IN SLP SPEED	CHECK/REPLACE PINCH ROLLER
GE	97520	N/A	NO TUNER VIDEO BUT PLAYS A TAPE OK	CHECK/REPLACE L708,R721 AND C723
GE	97520	N/A	TRACKING ADJUSTMENTS	MOST ACCURATELY PERFORMED IN SP MODE.
GE	97520	N/A	GARBLED AUDIO IN LP AND SLP	CHECK PINCH ROLLER,CLUTCH ASSY.;IDLER
GE	97520	N/A	WON'T RECORD -- MANUAL OR OTR	CLEAN OR REPLACE ERASE PROTECT SWITCH
GE	97520	N/A	DEAD WITH NO BLOWN FUSE OR REGULATOR TRANSISTOR	CHECK/REPLACE D1007 FOR SHORT (6.2V ZENER)
GE	97520	N/A	SNOW TO NORMAL PIX ON SELF RECORDED TAPES	CHECK CONNECTIONS ON IC2001 (ESPEC. PIN #2)
GE	97520	N/A	NO TUNER VIDEO BUT PLAYS A TAPE OK	CHECK/REPLACE L708,R721 AND C723
GE	97520	N/A	NO COLOR	ADJUST VCO,VXO--CHECK 3.58MHZ,4.2MHZ,629KHZ
GE	97520	N/A	AFTER UNIT RUNS FOR 1/2 TO 1 HOUR, DISPLAY GOES OUT AND VCR LOCKS UP - WON'T TAKE ANY COMMANDS	CHECK/REPLACE IC7502 (MN1280-R) RESET IC
GE	97520	N/A	PICTURE WOULD GO FROM GOOD TO SNOW-GOOD TO SNOW	CHECK/REPLACE C2023
GE	97520	N/A	NO CYLINDER OR CAPSTAN ACTION UNIT SHUTS DOWN	CHECK ICP-F38 (PR206)FOR OPEN CONDITION
GE	97520	N/A	NO FIP D1205 ON MAIN PWB BEING DRIVEN BEYOND TOL	CHECK C1018 FOR SHORTED CONDITION
GE	97520	N/A	NO DISPLAY AND NO FUSES BLOWN	CHECK/REPLACE C1015 AND C1016 (330uF @ 16v)
GE	97520	N/A	PIX JITTERS ON SPECIAL EFFECTS	CHECK V-LOCK ADJUSTMENT-WORN HEADS-PG SHIFTERS TR.FIX
GE	97520	N/A	FLOURESCENT DISPLAY VERY ERRATIC OR OUT COMPLETELY	CHECK/REPLACE C1004
GE	97520	N/A	POWER SUPPLY IS TICKING	CHECK D1007 FOR SHORT OR LEAKAGE
GE	97620	N/A	NO DISPLAY AND NO FUSES BLOWN	CHECK/REPLACE C1015 AND C1016 (330uF @ 16v)
GE	97655	N/A	DEAD - NO DISPLAY	CHECK/REPLACE C1015 AND C1016 (RCA P/N# 186753)
GE	97720	N/A	CAPSTAN SPINS THEN POWER SHUTS OFF (AT POWER UP)	CHECK IC6001 AND IC6002
GE	97720	N/A	PICTURE WOULD GO FROM GOOD TO SNOW-GOOD TO SNOW	CHECK/REPLACE C2023
GE	97720	N/A	DD CYLINDER RUNS FOR ABOUT 1 MINUTE - CHANNEL NUMBERS CHANGE BUT RECEIVES ONLY SNOW	CHECK/REPLACE D1008 AND R1010
GE	97720	N/A	TRACKING PROBLEMS IN SP MODE AND 'DONALD DUCK' IN LP AND SLP MODES	CHECK/REPLACE C2023 FOR SHORT
GE	97720	N/A	GARBLED AUDIO-TUNER AUDIO NOT SWITCHING ON P.B.	REPLACE IC4001
GE	97720	N/A	POWER SUPPLY IS TICKING	CHECK D1007 FOR SHORT OR LEAKAGE
GE	97720	N/A	TRACKING ADJUSTMENTS	MOST ACCURATELY PERFORMED IN SP MODE.
GE	97720	N/A	SUPPLY REELS START TURNING AS SOON AS UNIT IS PLUGGED IN BUT WILL NOT STAY ON - WILL NOT LOAD CASSETTE	CHECK/REPLACE R1010,D1008 AND C1011
GE	97720	N/A	DEAD SET AND SHORT ON THE 5 VOLT LINE	CHECK/REPLACE C3137 AND PR1001
GE	97720	N/A	PIX JITTERS ON SPECIAL EFFECTS	CHECK V-LOCK ADJUSTMENT-WORN HEADS-PG SHIFTERS TR.FIX
GE	97720	N/A	FLOURESCENT DISPLAY VERY ERRATIC OR OUT COMPLETELY	CHECK/REPLACE C1004
GE	97720	N/A	TV/VCR FUNCTIONS DOESN'T WORK BUT INDICATOR DOES LIGHT IN THE FIP DISPLAY	CHECK/REPLACE IC7601
GE	97720	N/A	GARBLED AUDIO IN LP AND SLP	CHECK PINCH ROLLER,CLUTCH ASSY.;IDLER
GE	97720	N/A	DEAD WITH NO BLOWN FUSE OR REGULATOR TRANSISTOR	CHECK/REPLACE D1007 FOR SHORT (6.2V ZENER)
GE	97720	N/A	WHEN UNIT IS PLUGGED IN,CAPSTAN RUNS 4-5 SECONDS AND SHUTS DOWN.	CHECK/REPLACE D1008 AND R1010
GE	97720	N/A	NO COLOR	ADJUST VCO,VXO--CHECK 3.58MHZ,4.2MHZ,629KHZ
GE	97720	N/A	AFTER UNIT RUNS FOR 1/2 TO 1 HOUR, DISPLAY GOES OUT AND VCR LOCKS UP - WON'T TAKE ANY COMMANDS	CHECK/REPLACE IC7502 (MN1280-R) RESET IC
GE	97720	N/A	WON'T RECORD -- MANUAL OR OTR	CLEAN OR REPLACE ERASE PROTECT SWITCH
GE	97720	N/A	ONE TICK FROM POWER SUPPLY-NO DISPLAY-NO POWER	CHECK PR1001,L1003,D1011,C1015 AND C1016
GE	97720	N/A	NO TUNER VIDEO BUT PLAYS A TAPE OK	CHECK/REPLACE L708,R721 AND C723
GE	97720	N/A	WOW & FLUTTER MOSTLY IN SLP SPEED	CHECK/REPLACE PINCH ROLLER
GE	97720	N/A	DEAD SET AND SHORT ON THE 5 VOLT LINE	CHECK/REPLACE C3137 AND PR1001
GE	97720	N/A	NO DISPLAY AND NO FUSES BLOWN	CHECK/REPLACE C1015 AND C1016 (330uF @ 16v)
GE	97720	N/A	DRUM MOTOR WILL NOT RUN	CHECK/REPLACE IC2603
GE	97720	N/A	NO AUDIO RECORDED AT ANY SPEED	CHECK IC4001
GE	97885	N/A	DEAD EXCEPT HI-FI LED'S FLASH	CHECK/REPLACE PR1 ON MAIN POWER SUPPLY
GE	97885	N/A	PLAYBACK PIX APPEARS SCRAMBLED	CHECK C3106
GE	97885	N/A	TUNER/PLAYBACK VIDEO FLUTTERS OR FLASHES	CHECK/REPLACE C1414,C1415,C1416 ON DIGITAL POWER SUPPLY-LOCATED BEHIND VIDEO DRUM AREA.
GE	97885	N/A	TUNER/PLAYBACK VIDEO FLUTTERS OR FLASHES	CHECK/REPLACE C1414,C1415,C1416 ON DIGITAL POWER SUPPLY-LOCATED BEHIND VIDEO DRUM AREA.
GE	97885	N/A	DEAD EXCEPT HI-FI LED'S FLASH	CHECK/REPLACE PR1 ON MAIN POWER SUPPLY
GE	97885	N/A	NO PLAYBACK CHROMA -MAY BE INTERMITTENT	CHECK/REPLACE IC8301-MAY BE THERMAL (AN3494NK)
GE	97885	N/A	NO PLAYBACK CHROMA -MAY BE INTERMITTENT	CHECK/REPLACE IC8301-MAY BE THERMAL (AN3494NK)
GE	VG2001	N/A	CASSETTE HANGS UP OR DOESN'T SIT PROPERLY WHEN TAPE IS LOADED	CHECK/REPLACE ITEM H552 (P/N# 210845), H573 (P/N# 207798), AND H556 (P/N# 201977)
GE	VG2001	N/A	WILL NOT ACCEPT TAPES	CHECK/REPLACE D112 AND D114 (IF PRESENT)
GE	VG2001	N/A	VCR WON'T ACCEPT SOME TAPES	CHECK/REPLACE ITEM H552 (P/N# 210845) WITH IMPROVED VERSION
GE	VG2001	N/A	INSERT TAPE,MACHINE LOADS TAPE AROUND HEADS BUT NO MOTORS ARE RUNNING,THEN UNLOADS LEAVING TAPE HANGING FROM TAPE.	CHECK/CLEAN MODE SELECT SWITCH
GE	VG2001	N/A	NO TUNER OPERATION--PLAYS TAPES OK	CHECK Q7 ON TUNER/IF BOARD
GE	VG2001	N/A	SLP SPEED VERY SLOW - WON'T TRACK SP AND LP GOOD	CHECK/REPLACE DRUM ASSEMBLY OR STATOR UNIT
GE	VG2001	N/A	NO TUNER - DRUM WILL NOT ROTATE - WON'T EJECT	CHECK/REPLACE Q108
GE	VG2001	N/A	PRESS PLAY AND UNIT SHUTS OFF IN 5 SECONDS	CLEAN DRIED MOLYTONE FOR GEAR DRIVE ASSY.-LUBRICATE
GE	VG2001	N/A	WON'T ACCEPT TAPE - IF MANUALLY LOADED, IT WON'T PLAY,REW, OR FAST FORWARD	CHECK/REPLACE D112
GE	VG2001	N/A	NO CAPSTAN MOTOR IN ANY FUNCTION OR MODE	CHECK/REPLACE R230 OPEN (MAY CHECK OK IN CIRCUIT)
GE	VG2001	N/A	DEAD - NO DISPLAY OR FUNCTIONS	CHECK/REPLACE C102
GE	VG2001	N/A	VCR WON'T ACCEPT SOME TAPES	CHECK/REPLACE ITEM H552 (P/N# 210845) WITH IMPROVED VERSION
GE	VG2001	N/A	INSERT TAPE,MACHINE LOADS TAPE AROUND HEADS BUT NO MOTORS ARE RUNNING,THEN UNLOADS LEAVING TAPE HANGING FROM TAPE.	CHECK/CLEAN MODE SELECT SWITCH
GE	VG2001	N/A	VCR IS SQUEALING WHILE PLAYING OR RECORDING - NOT PLAYING OR REWINDING TO END OF TAPE - UNIT MAY STOP INTERMITTENTLY	CHECK/REPLACE TAKE-UP REEL (P/N# 207491) AND SUPPLY REEL (P/N# 207492) - BOTH PARTS HAVE BEEN REVISED
GE	VG2001	N/A	PLAYS AND RECORDS BAD IN SLP ONLY	CHECK/REPLACE CAPSTAN MOTOR
GE	VG2001	N/A	WILL NOT ACCEPT TAPES	CHECK/REPLACE D112 AND D114 (IF PRESENT)
GE	VG2001	N/A	POOR AUDIO--AUDIO QUIVER--ESPECIALLY ON SLP	REPLACE CLUTCH ASSEMBLY (861-646-04)
GE	VG2001	N/A	MOTOR NOISE IN E-E WHEN LOADING OR UNLOADING A TAPE IN PB	CHECK/RESOLDER CONNECTIONS ON C112
GE	VG2001	N/A	WARBLE IN THE AUDIO ON ALL SPEEDS	CHECK/RESOLDER CONNECTIONS ON C112
GE	VG2001	N/A	CASSETTE HANGS UP OR DOESN'T SIT PROPERLY WHEN TAPE IS LOADED	CHECK/REPLACE ITEM H552 (P/N# 210845), H573 (P/N# 207798), AND H556 (P/N# 201977)
GE	VG2001	N/A	NO CAPSTAN MOTOR IN ANY FUNCTION OR MODE	CHECK/REPLACE R230 OPEN (MAY CHECK OK IN CIRCUIT)
GE	VG2007	N/A	SET TURNS ON/OFF - AS TAPE LOADS,DRUM RUNS TO FAST THEN SHUTS DOWN	CHECK/RESOLDER CONNECTIONS ON CN202 AND CN205 (SCRAPE PINS CLEAN)
GE	VG2007	N/A	VCR WON'T ACCEPT SOME TAPES	CHECK/REPLACE ITEM H552 (P/N# 210845) WITH IMPROVED VERSION
GE	VG2007	N/A	CASSETTE WILL NOT EJECT - NO FUNCTIONS	CHECK/REPLACE JOINT GEAR (65203-605-330) LOCATED ON THE RIGHT SIDE OF THE CARRIAGE (IF NOT METAL,REPLACE)
GE	VG2007	N/A	LOADS TAPE THEN UNLOADS - CAPSTAN AND DRUM MOTORS DON'T RUN	CHECK/REPLACE Q109
GE	VG2007	N/A	INSERT TAPE,MACHINE LOADS TAPE AROUND HEADS BUT NO MOTORS ARE RUNNING,THEN UNLOADS LEAVING TAPE HANGING FROM TAPE.	CHECK/CLEAN MODE SELECT SWITCH
GE	VG2007	N/A	LINES IN THE VIDEO DURING E-E MODE (TUNER MODE)	CHECK/RESOLDER CONNECTIONS ON COAX CABLE FROM THE TUNER TO THE RF CONVERTER
GE	VG2007	N/A	INTERFERENCE IN PIX - LOOKS LIKE MOTOR NOISE - NOISE STOPS WHEN CAPSTAN MOTOR STOPS	CHECK/REPLACE C112 FOR OPEN
GE	VG2007	N/A	LOADS TAPE THEN UNLOADS - CAPSTAN AND DRUM MOTORS DON'T RUN	CHECK/REPLACE Q109
GE	VG2007	N/A	WILL NOT ACCEPT TAPES	CHECK/REPLACE D112 AND D114 (IF PRESENT)
GE	VG2007	N/A	CASSETTE WILL NOT EJECT - NO FUNCTIONS	CHECK/REPLACE JOINT GEAR (65203-605-330) LOCATED ON THE RIGHT SIDE OF THE CARRIAGE (IF NOT METAL,REPLACE)
GE	VG2007	N/A	INSERT TAPE,MACHINE LOADS TAPE AROUND HEADS BUT NO MOTORS ARE RUNNING,THEN UNLOADS LEAVING TAPE HANGING FROM TAPE.	CHECK/CLEAN MODE SELECT SWITCH
GE	VG2007	N/A	WILL NOT ACCEPT TAPES	CHECK/REPLACE D112 AND D114 (IF PRESENT)
GE	VG2007	N/A	UNIT LOADS VERY SLOW	CHECK/REPLACE C102
GE	VG2007	N/A	VCR IS SQUEALING WHILE PLAYING OR RECORDING - NOT PLAYING OR REWINDING TO END OF TAPE - UNIT MAY STOP INTERMITTENTLY	CHECK/REPLACE TAKE-UP REEL (P/N# 207491) AND SUPPLY REEL (P/N# 207492) - BOTH PARTS HAVE BEEN REVISED
GE	VG2007	N/A	RADIATED INTERFERENCE	CHECK/REPLACE C112
GE	VG2007	N/A	NO FLOURESCENT DISPLAY	CHECK/REPLACE R102,R103,R116 AND ZD101
GE	VG2007	N/A	NO FLOURESCENT DISPLAY	CHECK/REPLACE R102,R103,R116 AND ZD101
GE	VG2007	N/A	LOADS SLOWLY	CHECK/REPLACE C102
GE	VG2007	N/A	CASSETTE HANGS UP OR DOESN'T SIT PROPERLY WHEN TAPE IS LOADED	CHECK/REPLACE ITEM H552 (P/N# 210845), H573 (P/N# 207798), AND H556 (P/N# 201977)
GE	VG2007	N/A	VCR WON'T ACCEPT SOME TAPES	CHECK/REPLACE ITEM H552 (P/N# 210845) WITH IMPROVED VERSION
GE	VG2010	N/A	DEAD - NO POWER	CHECK/REPLACE D1103 AND D1104
GE	VG2010	N/A	NO DISPLAY	CHECK/REPLACE D105 AND D106
GE	VG2010	N/A	TAPE WON'T LOAD	CHECK/REPLACE D111 AND D112
GE	VG2010	N/A	VCR WON'T ACCEPT SOME TAPES	CHECK/REPLACE ITEM H552 (P/N# 210845) WITH IMPROVED VERSION
GE	VG2010	N/A	LOUD GRINDING NOISE IN FAST FORWARD OR REWIND	CHECK/REPLACE DRIVE CLUTCH WHEEL (210841)
GE	VG2010	N/A	WILL NOT ACCEPT TAPES	CHECK/REPLACE D112 AND D114 (IF PRESENT)
GE	VG2010	N/A	TAPE WON'T LOAD	CHECK/REPLACE D111 AND D112
GE	VG2010	N/A	WILL FF AND REW BUT WILL NOT PLAY - EATS TAPES WHEN EJECTED	CHECK/REPLACE D108, D109, D110
GE	VG2010	N/A	VCR IS SQUEALING WHILE PLAYING OR RECORDING - NOT PLAYING OR REWINDING TO END OF TAPE - UNIT MAY STOP INTERMITTENTLY	CHECK/REPLACE TAKE-UP REEL (P/N# 207491) AND SUPPLY REEL (P/N# 207492) - BOTH PARTS HAVE BEEN REVISED
GE	VG2010	N/A	LOUD GRINDING NOISE IN FAST FORWARD OR REWIND	CHECK/REPLACE DRIVE CLUTCH WHEEL (210841)
GE	VG2010	N/A	CAPSTAN WON'T RUN IN THE PLAY MODE - REW/FF ARE OK	CHECK/REPLACE Q102
GE	VG2010	N/A	NO DISPLAY	CHECK/REPLACE D105 AND D106
GE	VG2010	N/A	DEAD	CHECK/REPLACE D1103 AND D1104
GE	VG2010	N/A	VCR WON'T ACCEPT SOME TAPES	CHECK/REPLACE ITEM H552 (P/N# 210845) WITH IMPROVED VERSION
GE	VG2010	N/A	CASSETTE HANGS UP OR DOESN'T SIT PROPERLY WHEN TAPE IS LOADED	CHECK/REPLACE ITEM H552 (P/N# 210845), H573 (P/N# 207798), AND H556 (P/N# 201977)
GE	VG2010	N/A	WILL FF AND REW BUT WILL NOT PLAY - EATS TAPES WHEN EJECTED	CHECK/REPLACE D108, D109, D110
GE	VG2010	N/A	DEAD - NO POWER	CHECK/REPLACE D1103 AND D1104
GE	VG2010	N/A	CASSETTE HANGS UP OR DOESN'T SIT PROPERLY WHEN TAPE IS LOADED	CHECK/REPLACE ITEM H552 (P/N# 210845), H573 (P/N# 207798), AND H556 (P/N# 201977)
GE	VG2010	N/A	CAPSTAN MOTOR WON'T RUN	CHECK/REPLACE D108,D109,D110
GE	VG2011	N/A	CAPSTAN MOTOR RUNS AT ERRATIC JERKING SPEED-IC2502 GETS HOT	CHECK/REPLACE OPEN FG HEAD ON CAPSTAN STATOR UNIT
GE	VG2013	N/A	CAPSTAN MOTOR RUNS AT ERRATIC JERKING SPEED-IC2502 GETS HOT	CHECK/REPLACE OPEN FG HEAD ON CAPSTAN STATOR UNIT
GE	VG2014	N/A	RIGHT CASSETTE HOLDER LOOSE AND GEARS MIS-ALIGNED	INSTALL TAB SUPPORT SPRING (210652)
GE	VG2016	N/A	VCR WON'T ACCEPT SOME TAPES	CHECK/REPLACE ITEM H552 (P/N# 210845) WITH IMPROVED VERSION
GE	VG2016	N/A	NO DISPLAY	CHECK/REPLACE D105 AND D106
GE	VG2016	N/A	WILL NOT ACCEPT TAPES	CHECK/REPLACE D112 AND D114 (IF PRESENT)
GE	VG2016	N/A	WILL FF AND REW BUT WILL NOT PLAY - EATS TAPES WHEN EJECTED	CHECK/REPLACE D108, D109, D110
GE	VG2016	N/A	VCR IS SQUEALING WHILE PLAYING OR RECORDING - NOT PLAYING OR REWINDING TO END OF TAPE - UNIT MAY STOP INTERMITTENTLY	CHECK/REPLACE TAKE-UP REEL (P/N# 207491) AND SUPPLY REEL (P/N# 207492) - BOTH PARTS HAVE BEEN REVISED
GE	VG2016	N/A	WILL NOT ACCEPT TAPES	CHECK/REPLACE D112 AND D114 (IF PRESENT)
GE	VG2016	N/A	DISPLAY AND TUNER OK BUT TRANSPORT WON'T RUN	CHECK/REPLACE IC1101
GE	VG2016	N/A	TAPE WON'T LOAD	CHECK/REPLACE D111 AND D112
GE	VG2016	N/A	UNIT DEAD - NO CASSETTE IN UNIT BUT CASSETTE INDICATOR IS ON	CHECK/REPLACE R637 (4.7k)
GE	VG2016	N/A	TAPE WON'T LOAD	CHECK/REPLACE D111 AND D112
GE	VG2016	N/A	LOUD GRINDING NOISE IN FAST FORWARD OR REWIND	CHECK/REPLACE DRIVE CLUTCH WHEEL (210841)
GE	VG2016	N/A	NO DISPLAY	CHECK/REPLACE D105 AND D106
GE	VG2016	N/A	E-E AND PLAYBACK VIDEO LEVEL LOW AND DISTORTED - VIDEO VERY WASHED OUT	CHECK/REPLACE IC302
GE	VG2016	N/A	CAPSTAN MOTOR WON'T RUN	CHECK/REPLACE D108,D109,D110
GE	VG2016	N/A	CAPSTAN SPEED IS TOO SLOW	CHECK/REPLACE IC201
GE	VG2016	N/A	WILL FF AND REW BUT WILL NOT PLAY - EATS TAPES WHEN EJECTED	CHECK/REPLACE D108, D109, D110
GE	VG2016	N/A	VCR WON'T ACCEPT SOME TAPES	CHECK/REPLACE ITEM H552 (P/N# 210845) WITH IMPROVED VERSION
GE	VG2016	N/A	NO DISPLAY AND NO FUNCTIONS WORK	CHECK/REPLACE R609
GE	VG2016	N/A	LOUD GRINDING NOISE IN FAST FORWARD OR REWIND	CHECK/REPLACE DRIVE CLUTCH WHEEL (210841)
GE	VG2016	N/A	DEAD - NO POWER	CHECK/REPLACE D1103 AND D1104
GE	VG2016	N/A	CAPSTAN MOTOR WON'T RUN	CHECK/REPLACE D108,D109,D110
GE	VG2016	N/A	INSERT TAPE,MACHINE LOADS TAPE AROUND HEADS BUT NO MOTORS ARE RUNNING,THEN UNLOADS LEAVING TAPE HANGING FROM TAPE.	CHECK/CLEAN MODE SELECT SWITCH
GE	VG2016	N/A	CASSETTE HANGS UP OR DOESN'T SIT PROPERLY WHEN TAPE IS LOADED	CHECK/REPLACE ITEM H552 (P/N# 210845), H573 (P/N# 207798), AND H556 (P/N# 201977)
GE	VG2016	N/A	CASSETTE HANGS UP OR DOESN'T SIT PROPERLY WHEN TAPE IS LOADED	CHECK/REPLACE ITEM H552 (P/N# 210845), H573 (P/N# 207798), AND H556 (P/N# 201977)
GE	VG2016	N/A	DEAD - NO POWER	CHECK/REPLACE D1103 AND D1104
GE	VG2021	N/A	PLAYBACK SPEED INCORRECT OR DISPLAY INDICATES THE WRONG SPEED	IF CAPSTAN MOTOR HAS BEEN REPLACED, BE SURE IT IS THE CORRECT TYPE - SHOULD BE (P/N# 212502)
GE	VG2021	N/A	DEAD - FRONT DISPLAY PULSATES ON AND OFF	CHECK/REPLACE C14 (220uF @ 16v - P/N# 189978)
GE	VG2021	N/A	CASSETTE TAPE WILL NOT LOAD OR EJECT OR CARRIAGE IS OUT OF TIME	CHECK/REPLACE RIGHT SIDE PLATE (P/N# 221066)
GE	VG2030	N/A	UNSTABLE OR WAVING PICTURE WHEN USING THE VCR'S RF CONVERTER	CHANGE R7005 TO A 200 1/4w. RESISTOR
GE	VG2030	N/A	TAPE SLACK OCCURS WHEN GOING FROM F/F OR REW TO STOP MODE	CHECK/REPLACE 'T' BRAKE SPRING (P/N# 228959)
GE	VG2035	N/A	PLAYBACK SPEED INCORRECT OR DISPLAY INDICATES THE WRONG SPEED	IF CAPSTAN MOTOR HAS BEEN REPLACED, BE SURE IT IS THE CORRECT TYPE - SHOULD BE (P/N# 220990)
GE	VG2056	N/A	NO DISPLAY - VCR WORKS FINE OTHERWISE	CHECK/REPLACE R62 (18?@ 1/10w)
GE	VG2058	N/A	VCR ONLY RECORDS NOISE ON CHANNELS ABOVE 13 WHEN USING THE VCR PLUS MODE	CHECK/REPLACE IC601 (P/N# 235539)
GE	VG2058	N/A	NO DISPLAY - VCR WORKS FINE OTHERWISE	CHECK/REPLACE R62 (18?@ 1/10w)
GE	VG4005	N/A	DISTORTED E-E AUDIO/VIDEO - VCR SHUTSDOWN WHEN GOING TO PLAY MODE	CHECK/REPLACE C102 IN POWER SUPPLY
GE	VG4005	N/A	AUDIO AND VIDEO ARE DISTORTED IN THE E-E MODE AND VCR SHUTS DOWN WHEN PRESSING PLAY	CHECK/REPLACE C102 (330uF @ 35v)
GE	VG4005	N/A	NO DISPLAY BUT UNIT DOES OPERATE FINE	CHECK/REPLACE R102 AND R103
GE	VG4005	N/A	WON'T RECORD VIDEO	CHECK/REPLACE C331 IN Y/C CIRCUIT
GE	VG4005	N/A	SLOW TURNING DRUM - INTERMITTENT FUNCTIONS	CHECK/REPLACE C102 (3300uF @ 25v)
GE	VG4005	N/A	VCR WON'T ACCEPT SOME TAPES	CHECK/REPLACE ITEM H552 (P/N# 210845) WITH IMPROVED VERSION
GE	VG4005	N/A	PIX OK - SOUND OK ON VOICE BUT DRAGS ON MUSIC	CHECK ALIGNMENT OF AUDIO/CTRL HEAD (HORZ 2 POSITION)
GE	VG4005	N/A	CASSETTE HANGS UP OR DOESN'T SIT PROPERLY WHEN TAPE IS LOADED	CHECK/REPLACE ITEM H552 (P/N# 210845), H573 (P/N# 207798), AND H556 (P/N# 201977)
GE	VG4005	N/A	IN THE PLAY MODE,DRUM SPEED INCREASES AND SHUTS DOWN	CHECK/REPLACE INTERMITTENT MOTOR STATOR (T305)
GE	VG4005	N/A	WILL NOT ACCEPT TAPES	CHECK/REPLACE D112 AND D114 (IF PRESENT)
GE	VG4005	N/A	VCR WON'T ACCEPT SOME TAPES	CHECK/REPLACE ITEM H552 (P/N# 210845) WITH IMPROVED VERSION
GE	VG4005	N/A	DRUM RUN-AWAY	CHECK/RESOLDER CONNECTIONS ON STAPLES OR JUMPERS LOCATED ON DRUM STATOR UNIT
GE	VG4005	N/A	VCR IS SQUEALING WHILE PLAYING OR RECORDING - NOT PLAYING OR REWINDING TO END OF TAPE - UNIT MAY STOP INTERMITTENTLY	CHECK/REPLACE TAKE-UP REEL (P/N# 207491) AND SUPPLY REEL (P/N# 207492) - BOTH PARTS HAVE BEEN REVISED
GE	VG4005	N/A	CASSETTE HANGS UP OR DOESN'T SIT PROPERLY WHEN TAPE IS LOADED	CHECK/REPLACE ITEM H552 (P/N# 210845), H573 (P/N# 207798), AND H556 (P/N# 201977)
GE	VG4005	N/A	UNIT SHUTS DOWN WHEN PLAY OR RECORD MODE IS SELECTED	CHECK/REPLACE DRUM MOTOR STATOR ASSEMBLY
GE	VG4005	N/A	WILL NOT ACCEPT TAPES	CHECK/REPLACE D112 AND D114 (IF PRESENT)
GE	VG4005	N/A	TAPE LOADS BUT NO OTHER FUNCTIONS WORK - DISPLAY OK	CHECK/REPLACE C103 (3300uF @ 35v)
GE	VG4005	N/A	LP AND SLP RECORDING PLAYED BACK SNOW ONLY - SP IS FINE - LOOKS LIKE A BAD HEAD	CHECK/REPLACE IC6101
GE	VG4011	N/A	MICROPROCESSOR LOCK-UP OR IMPROPER RESET	CHANGE C6001 TO A 1uF @ 50v
GE	VG4011	N/A	MICROPROCESSOR LOCK-UP OR IMPROPER RESET	CHANGE C6001 TO A 1uF @ 50v
GE	VG4011	N/A	RIGHT CASSETTE HOLDER LOOSE AND GEARS MIS-ALIGNED	INSTALL TAB SUPPORT SPRING (210652)
GE	VG4011	N/A	NO AUDIO OR VIDEO FROM TUNER OR TAPE	CHECK/REPLACE Q1201
GE	VG4012	N/A	RIGHT CASSETTE HOLDER LOOSE AND GEARS MIS-ALIGNED	INSTALL TAB SUPPORT SPRING (210652)
GE	VG4014	N/A	PLAYBACK SPEED INCORRECT OR DISPLAY INDICATES THE WRONG SPEED	IF CAPSTAN MOTOR HAS BEEN REPLACED, BE SURE IT IS THE CORRECT TYPE - SHOULD BE (P/N# 212502)
GE	VG4014	N/A	AUDIO BUT NO PICTURE IN PLAYBACK MODE	CHECK/REPLACE D303 AND D306 FOR OPEN
GE	VG4014	N/A	NO CHROMA ON RECORD - WILL PLAYBACK COLOR FROM A KNOWN GOOD TAPE	CHECK/REPLACE IC302
GE	VG4014	N/A	INTERMITTENTLY EATS TAPES OR DOESN'T WANT TO LOAD TAPES OR MAY SHUTDOWN	CHECK/REPLACE MODE SELECT SWITCH
GE	VG4014	N/A	UNIT ACCEPTS TAPE BUT WILL NOT LOAD OR UNLOAD TAPE AROUND HEADS	CHECK/REPLACE IC101
GE	VG4014	N/A	DEAD - FRONT DISPLAY PULSATES ON AND OFF	CHECK/REPLACE C14 (220uF @ 16v - P/N# 189978)
GE	VG4014	N/A	PLAYBACK SPEED INCORRECT OR DISPLAY INDICATES THE WRONG SPEED	IF CAPSTAN MOTOR HAS BEEN REPLACED, BE SURE IT IS THE CORRECT TYPE - SHOULD BE (P/N# 212502)
GE	VG4014	N/A	DEAD WITH OR WITHOUT FUSE BLOWN	CHECK/REPLACE Q1,Q2 AND D02 IN POWER SUPPLY
GE	VG4014	N/A	CASSETTE TAPE WILL NOT LOAD OR EJECT OR CARRIAGE IS OUT OF TIME	CHECK/REPLACE RIGHT SIDE PLATE (P/N# 221066)
GE	VG4014	N/A	CASSETTE TAPE WILL NOT LOAD OR EJECT OR CARRIAGE IS OUT OF TIME	CHECK/REPLACE RIGHT SIDE PLATE (P/N# 221066)
GE	VG4014	N/A	DEAD - FRONT DISPLAY PULSATES ON AND OFF	CHECK/REPLACE C14 (220uF @ 16v - P/N# 189978)
GE	VG4014	N/A	ERRATIC OPERATION - MAY LOAD TAPE BUT NOT EJECT OR JUMP OUT OF TIME ON LOAD/UNLOADING OF TAPE	CHECK/REPLACE CAM SWITCH (P/N# 212516)
GE	VG4016	N/A	VCR IS SQUEALING WHILE PLAYING OR RECORDING - NOT PLAYING OR REWINDING TO END OF TAPE - UNIT MAY STOP INTERMITTENTLY	CHECK/REPLACE TAKE-UP REEL (P/N# 207491) AND SUPPLY REEL (P/N# 207492) - BOTH PARTS HAVE BEEN REVISED
GE	VG4016	N/A	CAPSTAN MOTOR WON'T RUN	CHECK/REPLACE D108,D109,D110
GE	VG4016	N/A	PRE-RECORDED TAPES PLAY OK BUT TAPES RECORDED ON ANOTHER VCR HAVE TRACKING LINES IN PICTURE	CHECK/REPLACE IC201
GE	VG4016	N/A	CAPSTAN MOTOR WON'T RUN IN PLAY MODE	CHECK/REPLACE D111
GE	VG4016	N/A	WILL NOT ACCEPT TAPES	CHECK/REPLACE D112 AND D114 (IF PRESENT)
GE	VG4016	N/A	WILL FF AND REW BUT WILL NOT PLAY - EATS TAPES WHEN EJECTED	CHECK/REPLACE D108, D109, D110
GE	VG4016	N/A	TAPE WON'T LOAD	CHECK/REPLACE D111 AND D112
GE	VG4016	N/A	NO DISPLAY	CHECK/REPLACE D105 AND D106
GE	VG4016	N/A	ALL TAPES ENTER PLAY MODE - PRESSING THE RECORD BUTTON CAUSES TAPES TO EJECT	CHECK/REPLACE R645 OPEN
GE	VG4016	N/A	INTERMITTENT REWIND AND MAKING A LOUD NOISE	CHECK FOR MISSING WASHER ON CLUTCH ASSY. (#956)
GE	VG4016	N/A	CASSETTE HANGS UP OR DOESN'T SIT PROPERLY WHEN TAPE IS LOADED	CHECK/REPLACE ITEM H552 (P/N# 210845), H573 (P/N# 207798), AND H556 (P/N# 201977)
GE	VG4016	N/A	AS SOON AS AC IS PLUGGED IN, CAPSTAN MOTOR AND LOADING MOTOR TURN IN REVERSE	CHECK/REPLACE START AND END SENSORS
GE	VG4016	N/A	LOUD GRINDING NOISE IN FAST FORWARD OR REWIND	CHECK/REPLACE DRIVE CLUTCH WHEEL (210841)
GE	VG4016	N/A	TAPE WON'T LOAD	CHECK/REPLACE D111 AND D112
GE	VG4016	N/A	VCR WON'T ACCEPT SOME TAPES	CHECK/REPLACE ITEM H552 (P/N# 210845) WITH IMPROVED VERSION
GE	VG4016	N/A	WILL NOT ACCEPT TAPES	CHECK/REPLACE D112 AND D114 (IF PRESENT)
GE	VG4016	N/A	DEAD SET	CHECK/REPLACE XT601
GE	VG4016	N/A	VCR WON'T ACCEPT SOME TAPES	CHECK/REPLACE ITEM H552 (P/N# 210845) WITH IMPROVED VERSION
GE	VG4016	N/A	CASSETTE HANGS UP OR DOESN'T SIT PROPERLY WHEN TAPE IS LOADED	CHECK/REPLACE ITEM H552 (P/N# 210845), H573 (P/N# 207798), AND H556 (P/N# 201977)
GE	VG4016	N/A	LOADS TAPE THEN VCR SHUTS OFF - LOOKS LIKE MODE SELECT SWITCH OR SYSCON PROBLEM	CHECK/REPLACE SERVO IC (KA8319) P/N# 207792
GE	VG4016	N/A	VCR LOOSES CLOCK AND POWER INTERMITTENTLY	CHECK/REPLACE D602 AND IC602
GE	VG4016	N/A	CAPSTAN MOTOR WON'T RUN	CHECK/REPLACE D108,D109,D110
GE	VG4016	N/A	NO AUDIO ON PLAYBACK - TUNER AUDIO IS NORMAL	CHECK/REPLACE R514
GE	VG4016	N/A	NO DISPLAY	CHECK/REPLACE D105 AND D106
GE	VG4016	N/A	LOUD GRINDING NOISE IN FAST FORWARD OR REWIND	CHECK/REPLACE DRIVE CLUTCH WHEEL (210841)
GE	VG4016	N/A	VERTICAL JITTER ON PLAYBACK OF ALL TAPES	CHECK/REPLACE IC302
GE	VG4016	N/A	DEAD - NO POWER	CHECK/REPLACE D1103 AND D1104
GE	VG4016	N/A	DEAD - NO POWER	CHECK/REPLACE D1103 AND D1104
GE	VG4018	N/A	CLOCK LOSES ABOUT 15 MINUTES PER DAY	CHECK FOR A SOLDER BRIDGE BETWEEN PINS 23 AND 24 OF IC751
GE	VG4018	N/A	WON'T ALWAYS LOAD TAPE - TAPE SPEED TOO FAST IN SP MODE - WHEN GOING TO EJECT,MACHINE SHUTS DOWN INSTEAD	CHECK/REPLACE CAPSTAN MOTOR
GE	VG4018	N/A	WILL NOT ACCEPT TAPES	CHECK/REPLACE D112 AND D114 (IF PRESENT)
GE	VG4018	N/A	VERY NOISY ON REWIND/FAST FORWARD/EJECT	LUBRICATE CAPSTAN MOTOR SHAFT
GE	VG4018	N/A	MISCELLANEOUS CONTROL PROBLEMS - ERRATIC OPERATIONS - DAMAGES TAPE - WON'T EJECT	CLEAN EXCESSIVE FLUX FROM THE PINS OF IC751 AND SURROUNDING AREA
GE	VG4018	N/A	WON'T ALWAYS LOAD TAPE - TAPE SPEED TOO FAST IN SP MODE - WHEN GOING TO EJECT,MACHINE SHUTS DOWN INSTEAD	CHECK/REPLACE CAPSTAN MOTOR
GE	VG4018	N/A	NO COLOR ON PLAYBACK	HARDWIRE P6833/P6233 PIN 1
GE	VG4018	N/A	INTERMITTENT LOADING - LOUD NOISE AND TAPE IN LIGHT STAYS ON WITH NO CASSETTE	CHECK/RESOLDER CONNECTIONS ON END SENSORS
GE	VG4019	N/A	VCR PLUS CHANNEL GUIDE SETUP DOES NOT STORE SOME CHANNEL NUMBERS	CHECK TO SEE IF PIN 7 OF IC604 IS GROUNDED-CHECK PINS 5&6 OF IC604 FOR 4vpp-IF LOW CHECK R646,653,647,652 & IC601,2,4
GE	VG4019	N/A	DEAD - FRONT DISPLAY PULSATES ON AND OFF	CHECK/REPLACE C14 (220uF @ 16v - P/N# 189978)
GE	VG4019	N/A	CASSETTE TAPE WILL NOT LOAD OR EJECT OR CARRIAGE IS OUT OF TIME	CHECK/REPLACE RIGHT SIDE PLATE (P/N# 221066)
GE	VG4019	N/A	DEAD - FRONT DISPLAY PULSATES ON AND OFF	CHECK/REPLACE C14 (220uF @ 16v - P/N# 189978)
GE	VG4019	N/A	ERRATIC OPERATION - MAY LOAD TAPE BUT NOT EJECT OR JUMP OUT OF TIME ON LOAD/UNLOADING OF TAPE	CHECK/REPLACE CAM SWITCH (P/N# 212516)
GE	VG4019	N/A	DEAD WITH OR WITHOUT FUSE BLOWN	CHECK/REPLACE Q1,Q2 AND D02 IN POWER SUPPLY
GE	VG4019	N/A	NO CHROMA ON RECORD - WILL PLAYBACK COLOR FROM A KNOWN GOOD TAPE	CHECK/REPLACE IC302
GE	VG4019	N/A	CASSETTE TAPE WILL NOT LOAD OR EJECT OR CARRIAGE IS OUT OF TIME	CHECK/REPLACE RIGHT SIDE PLATE (P/N# 221066)
GE	VG4019	N/A	INTERMITTENTLY EATS TAPES OR DOESN'T WANT TO LOAD TAPES OR MAY SHUTDOWN	CHECK/REPLACE MODE SELECT SWITCH
GE	VG4019	N/A	PLAYBACK SPEED INCORRECT OR DISPLAY INDICATES THE WRONG SPEED	IF CAPSTAN MOTOR HAS BEEN REPLACED, BE SURE IT IS THE CORRECT TYPE - SHOULD BE (P/N# 212502)
GE	VG4019	N/A	PLAYBACK SPEED INCORRECT OR DISPLAY INDICATES THE WRONG SPEED	IF CAPSTAN MOTOR HAS BEEN REPLACED, BE SURE IT IS THE CORRECT TYPE - SHOULD BE (P/N# 212502)
GE	VG4019	N/A	AUDIO BUT NO PICTURE IN PLAYBACK MODE	CHECK/REPLACE D303 AND D306 FOR OPEN
GE	VG4025	N/A	PLAYBACK SPEED INCORRECT OR DISPLAY INDICATES THE WRONG SPEED	IF CAPSTAN MOTOR HAS BEEN REPLACED, BE SURE IT IS THE CORRECT TYPE - SHOULD BE (P/N# 218966)
GE	VG4025	N/A	DEAD - FRONT DISPLAY PULSATES ON AND OFF	CHECK/REPLACE C14 (470uF @ 16v - P/N# 176251)
GE	VG4025	N/A	CASSETTE TAPE WILL NOT LOAD OR EJECT OR CARRIAGE IS OUT OF TIME	CHECK/REPLACE RIGHT SIDE PLATE (P/N# 221066)
GE	VG4029	N/A	PLAYBACK SPEED INCORRECT OR DISPLAY INDICATES THE WRONG SPEED	IF CAPSTAN MOTOR HAS BEEN REPLACED, BE SURE IT IS THE CORRECT TYPE - SHOULD BE (P/N# 218966)
GE	VG4029	N/A	CASSETTE TAPE WILL NOT LOAD OR EJECT OR CARRIAGE IS OUT OF TIME	CHECK/REPLACE RIGHT SIDE PLATE (P/N# 221066)
GE	VG4029	N/A	DEAD - FRONT DISPLAY PULSATES ON AND OFF	CHECK/REPLACE C14 (470uF @ 16v - P/N# 176251)
GE	VG4030	N/A	TAPE SLACK OCCURS WHEN GOING FROM F/F OR REW TO STOP MODE	CHECK/REPLACE 'T' BRAKE SPRING (P/N# 228959)
GE	VG4030	N/A	UNSTABLE OR WAVING PICTURE WHEN USING THE VCR'S RF CONVERTER	CHANGE R7005 TO A 200 1/4w. RESISTOR
GE	VG4031	N/A	TAPE SLACK OCCURS WHEN GOING FROM F/F OR REW TO STOP MODE	CHECK/REPLACE 'T' BRAKE SPRING (P/N# 228959)
GE	VG4031	N/A	UNSTABLE OR WAVING PICTURE WHEN USING THE VCR'S RF CONVERTER	CHANGE R7005 TO A 200 1/4w. RESISTOR
GE	VG4032	N/A	TAPE SLACK OCCURS WHEN GOING FROM F/F OR REW TO STOP MODE	CHECK/REPLACE 'T' BRAKE SPRING (P/N# 228959)
GE	VG4032	N/A	UNSTABLE OR WAVING PICTURE WHEN USING THE VCR'S RF CONVERTER	CHANGE R7005 TO A 200 1/4w. RESISTOR
GE	VG4033	N/A	UNSTABLE OR WAVING PICTURE WHEN USING THE VCR'S RF CONVERTER	CHANGE R7005 TO A 200 1/4w. RESISTOR
GE	VG4033	N/A	TAPE SLACK OCCURS WHEN GOING FROM F/F OR REW TO STOP MODE	CHECK/REPLACE 'T' BRAKE SPRING (P/N# 228959)
GE	VG4035	N/A	PLAYBACK SPEED INCORRECT OR DISPLAY INDICATES THE WRONG SPEED	IF CAPSTAN MOTOR HAS BEEN REPLACED, BE SURE IT IS THE CORRECT TYPE - SHOULD BE (P/N# 220990)
GE	VG4036	N/A	PLAYBACK SPEED INCORRECT OR DISPLAY INDICATES THE WRONG SPEED	IF CAPSTAN MOTOR HAS BEEN REPLACED, BE SURE IT IS THE CORRECT TYPE - SHOULD BE (P/N# 220990)
GE	VG4038	N/A	FRONT PANEL TRACKING BUTTONS INOPERATIVE	THESE BUTTONS CANNOT BE HELD DOWN - THEY HAVE TO BE PRESSED AND RELEASED REPEATEDLY
GE	VG4038	N/A	WHITE DOT OR TADPOLE NOISE IN THE PLAYBACK VIDEO EARLY PROD. BOARDS MRK'D (20194390.00.000)	INSTALL KIT (P/N# 229296)
GE	VG4038	N/A	VCR IS COMPLETELY DEAD	CHECK/REPLACE DP026 AND DP027 - MOVE ANODE OF DP027 TO THE OPPOSITE END OF LP002 - INSTALL KIT (P/N# 231734)
GE	VG4038	N/A	DRUM DOES NOT ROTATE	CHECK FOR DUST AROUND THE POST OF THE OPTICAL PICKUP ON THE DRUM MOTOR FLYWHEEL - ANY BUILD UP CAN BE A PROBLEM
GE	VG4038	N/A	NO COLOR IN LP SEARCH	THIS IS NOT A MALFUNCTION BUT A DESIGN CHARACTERISTIC
GE	VG4038	N/A	DEAD SET	CHECK/REPLACE MODIFICATION KIT (P/N# 231734)
GE	VG4038	N/A	ROLLING/FLOATING VERTICAL BAR WHEN PLAYING BACK SELF RECORDED TAPES - EARLY PROD. BOARDS MRK'D (20194390.00.000)	INSTALL KIT (P/N# 229296)
GE	VG4039	N/A	FRONT PANEL TRACKING BUTTONS INOPERATIVE	THESE BUTTONS CANNOT BE HELD DOWN - THEY HAVE TO BE PRESSED AND RELEASED REPEATEDLY
GE	VG4039	N/A	NO COLOR IN LP SEARCH	THIS IS NOT A MALFUNCTION BUT A DESIGN CHARACTERISTIC
GE	VG4039	N/A	FLUORESCENT DISPLAY FLASHES INTERMITTENTLY ONLY WHEN THE UNIT IS IN THE OFF MODE - MAY GO FROM TIME DISPLAY TO --:--	ADD INTERRUPT CBA (P/N# 233212)
GE	VG4039	N/A	VCR IS COMPLETELY DEAD	CHECK/REPLACE DP026 AND DP027 - MOVE ANODE OF DP027 TO THE OPPOSITE END OF LP002 - INSTALL KIT (P/N# 231734)
GE	VG4039	N/A	DRUM DOES NOT ROTATE	CHECK FOR DUST AROUND THE POST OF THE OPTICAL PICKUP ON THE DRUM MOTOR FLYWHEEL - ANY BUILD UP CAN BE A PROBLEM
GE	VG4039	N/A	WHITE DOT OR TADPOLE NOISE IN THE PLAYBACK VIDEO EARLY PROD. BOARDS MRK'D (20194390.00.000)	INSTALL KIT (P/N# 229296)
GE	VG4039	N/A	ROLLING/FLOATING VERTICAL BAR WHEN PLAYING BACK SELF RECORDED TAPES - EARLY PROD. BOARDS MRK'D (20194390.00.000)	INSTALL KIT (P/N# 229296)
GE	VG4039	N/A	DEAD SET	CHECK/REPLACE MODIFICATION KIT (P/N# 231734)
GE	VG4039	N/A	FLUORESCENT DISPLAY FLASHES INTERMITTENTLY ONLY WHEN THE UNIT IS IN THE OFF MODE - MAY GO FROM TIME DISPLAY TO --:--	CHECK/REPLACE IT001 (P/N# 229330)
GE	VG4055	N/A	DISTORTED/GARBLED LINEAR AUDIO DURING SLP PLAYBACK ONLY	CHECK/REPLACE IC601 (P/N# 231932) WITH NEW TYPE
GE	VG4055	N/A	WAVY PICTURE ON PLAYBACK OR SQUEAL FROM CAPSTAN MOTOR	CHECK/REPLACE FELT PAD UNDER THE CAPSTAN MOTOR (P/N 233964)
GE	VG4055	N/A	VCR TURNS OFF AFTER POWERED ON OR UNIT HAS EXCESSIVE DRUM SPEED	CHECK/RESOLDER CONNECTIONS ON 6 PIN POWER CONNECTOR TO THE DRUM MOTOR -- THIS CONNECTOR IS SURFACE MOUNTED
GE	VG4055	N/A	CASSETTE TAPE DOES NOT SLOW DOWN AT THE END OF HIGH SPEED REWIND	CHECK/REPLACE DIODE LOCATED ON THE EMITTER LEG OF Q202
GE	VG4056	N/A	NO DISPLAY - VCR WORKS FINE OTHERWISE	CHECK/REPLACE R62 (18?@ 1/10w)
GE	VG4058	N/A	VCR SHUTS OFF AFTER THE TAPE IS LOADED	CHECK/REPLACE SW601 (P/N# 229178)
GE	VG4200	N/A	NO AUDIO FROM TUNER OR LINE	CHECK/REPLACE R1205,D1007,C1014 AND C1021
GE	VG4202	N/A	INTERMITTENT AUDIO OR VERY LOW AUDIO	CHECK/REPLACE IC4001
GE	VG4210	N/A	PLAYBACK SPEED INCORRECT OR DISPLAY INDICATES THE WRONG SPEED	IF CAPSTAN MOTOR HAS BEEN REPLACED, BE SURE IT IS THE CORRECT TYPE - SHOULD BE (P/N# 218966)
GE	VG4210	N/A	CASSETTE TAPE WILL NOT LOAD OR EJECT OR CARRIAGE IS OUT OF TIME	CHECK/REPLACE RIGHT SIDE PLATE (P/N# 221066)
GE	VG4210	N/A	DEAD - FRONT DISPLAY PULSATES ON AND OFF	CHECK/REPLACE C14 (470uF @ 16v - P/N# 176251)
GE	VG4215	N/A	CASSETTE TAPE WILL NOT LOAD OR EJECT OR CARRIAGE IS OUT OF TIME	CHECK/REPLACE RIGHT SIDE PLATE (P/N# 221066)
GE	VG4215	N/A	DEAD - NO CLOCK OR CLOCK PULSATES ON/OFF - WILL NOT TAKE A TAPE	CHECK/REPLACE C09 IN POWER SUPPLY (22uF @ 16v)
GE	VG4215	N/A	DEAD - FRONT DISPLAY PULSATES ON AND OFF	CHECK/REPLACE C14 (470uF @ 16v - P/N# 176251)
GE	VG4215	N/A	PLAYBACK SPEED INCORRECT OR DISPLAY INDICATES THE WRONG SPEED	IF CAPSTAN MOTOR HAS BEEN REPLACED, BE SURE IT IS THE CORRECT TYPE - SHOULD BE (P/N# 218966)
GE	VG4216	N/A	DEAD - NO POWER	CHECK/REPLACE D1103 AND D1104
GE	VG4216	N/A	TAPE WON'T LOAD	CHECK/REPLACE D111 AND D112
GE	VG4216	N/A	LOUD GRINDING NOISE IN FAST FORWARD OR REWIND	CHECK/REPLACE DRIVE CLUTCH WHEEL (210841)
GE	VG4216	N/A	VCR WON'T ACCEPT SOME TAPES	CHECK/REPLACE ITEM H552 (P/N# 210845) WITH IMPROVED VERSION
GE	VG4216	N/A	CASSETTE HANGS UP OR DOESN'T SIT PROPERLY WHEN TAPE IS LOADED	CHECK/REPLACE ITEM H552 (P/N# 210845), H573 (P/N# 207798), AND H556 (P/N# 201977)
GE	VG4216	N/A	WILL NOT TUNE SOME CHANNELS CORRECTLY ON A HRC CABLE SYSTEM	CHANGE R409 TO A 100k AND ADD A 100k FROM PIN 14 OF IC401 TO GROUND
GE	VG4216	N/A	NO DISPLAY	CHECK/REPLACE D105 AND D106
GE	VG4216	N/A	NO 'AL' 6 VOLTS	CHECK/REPLACE D1103 AND D1104 (MAY CHECK NORMAL)
GE	VG4216	N/A	DEAD - NO POWER	CHECK/REPLACE D1103 AND D1104
GE	VG4216	N/A	VCR IS SQUEALING WHILE PLAYING OR RECORDING - NOT PLAYING OR REWINDING TO END OF TAPE - UNIT MAY STOP INTERMITTENTLY	CHECK/REPLACE TAKE-UP REEL (P/N# 207491) AND SUPPLY REEL (P/N# 207492) - BOTH PARTS HAVE BEEN REVISED
GE	VG4216	N/A	CAPSTAN MOTOR WON'T RUN	CHECK/REPLACE D108,D109,D110
GE	VG4216	N/A	VCR WON'T ACCEPT SOME TAPES	CHECK/REPLACE ITEM H552 (P/N# 210845) WITH IMPROVED VERSION
GE	VG4216	N/A	CASSETTE HANGS UP OR DOESN'T SIT PROPERLY WHEN TAPE IS LOADED	CHECK/REPLACE ITEM H552 (P/N# 210845), H573 (P/N# 207798), AND H556 (P/N# 201977)
GE	VG4216	N/A	WILL NOT ACCEPT TAPES	CHECK/REPLACE D112 AND D114 (IF PRESENT)
GE	VG4216	N/A	NO 'AL' 6 VOLTS	CHECK/REPLACE D1103 AND D1104 (MAY CHECK NORMAL)
GE	VG4216	N/A	CAPSTAN MOTOR WON'T RUN	CHECK/REPLACE D108,D109,D110
GE	VG4216	N/A	EATS TAPES WHEN GOING FROM PLAY TO EJECT	CHECK/REPLACE D108,D109,D110 FOR OPEN
GE	VG4216	N/A	DEAD - NO CLOCK OR CLOCK PULSATES ON/OFF - WILL NOT TAKE A TAPE	CHECK/REPLACE C09 IN POWER SUPPLY (22uF @ 16v)
GE	VG4216	N/A	LOUD GRINDING NOISE IN FAST FORWARD OR REWIND	CHECK/REPLACE DRIVE CLUTCH WHEEL (210841)
GE	VG4216	N/A	WILL NOT ACCEPT TAPES	CHECK/REPLACE D112 AND D114 (IF PRESENT)
GE	VG4216	N/A	NO BLUE BACKGROUND - CAN'T SET CLOCK OR PROGRAM - ALL OTHER VCR FUNCTIONS ARE NORMAL	CHECK/REPLACE IC901
GE	VG4216	N/A	NO DISPLAY	CHECK/REPLACE D105 AND D106
GE	VG4216	N/A	TAPE WON'T LOAD	CHECK/REPLACE D111 AND D112
GE	VG4216	N/A	EATS TAPES WHEN GOING FROM PLAY TO EJECT	CHECK/REPLACE D108,D109,D110 FOR OPEN
GE	VG4216	N/A	WILL NOT TUNE SOME CHANNELS CORRECTLY ON A HRC CABLE SYSTEM	CHANGE R409 TO A 100k AND ADD A 100k FROM PIN 14 OF IC401 TO GROUND
GE	VG4217	N/A	DEAD - FRONT DISPLAY PULSATES ON AND OFF	CHECK/REPLACE C14 (220uF @ 16v - P/N# 189978)
GE	VG4217	N/A	VCR WILL NOT MUTE WHEN GOING INTO FAST SEARCH OR REWIND SEARCH	CHECK/REPLACE IC5201 (P/N# 213840)
GE	VG4217	N/A	VCR WILL NOT MUTE WHEN GOING INTO FAST SEARCH OR REWIND SEARCH	CHECK/REPLACE IC5201 (P/N# 213840)
GE	VG4217	N/A	PLAYBACK SPEED INCORRECT OR DISPLAY INDICATES THE WRONG SPEED	IF CAPSTAN MOTOR HAS BEEN REPLACED, BE SURE IT IS THE CORRECT TYPE - SHOULD BE (P/N# 212502)
GE	VG4217	N/A	CASSETTE TAPE WILL NOT LOAD OR EJECT OR CARRIAGE IS OUT OF TIME	CHECK/REPLACE RIGHT SIDE PLATE (P/N# 221066)
GE	VG4217	N/A	WILL NOT RECORD IN LP OR SLP BUT SP IS NORMAL	CHECK/REPLACE IC301
GE	VG4217	N/A	DEAD - FRONT DISPLAY PULSATES ON AND OFF	CHECK/REPLACE C14 (220uF @ 16v - P/N# 189978)
GE	VG4217	N/A	CASSETTE TAPE WILL NOT LOAD OR EJECT OR CARRIAGE IS OUT OF TIME	CHECK/REPLACE RIGHT SIDE PLATE (P/N# 221066)
GE	VG4218	N/A	WILL NOT ACCEPT TAPE - 12 VOLTS ON LOADING IC MISSING	CHECK/REPLACE D001 (33 VOLT ZENER)
GE	VG4218	N/A	ERRATIC FAST FORWARD OPERATION - UNIT MAY NOT PLAY,SEARCH FORWARD OR FFWD - DOES MOVE IN REVIEW/REWIND - EATS TAPES	CHECK/REPLACE Q512 FOR LEAKAGE (CAPSTAN SWITCH)
GE	VG4218	N/A	ON TUNER, PICTURE JUMPS AND IS PARTIALLY 'BLUE SCREEN'	CHECK/REPLACE C026
GE	VG4218	N/A	CLOCK DISPLAY ON BUT NO OTHER FUNCTIONS WORK - WILL NOT LOAD/EJECT TAPE	CHECK/REPLACE Z611 (CIRCUIT PROTECTOR)
GE	VG4218	N/A	NO CHROMA OR INTERMITTENT CHROMA ON PLAYBACK BUT RECORD CHROMA IS OK WHEN PLAYED ON ANOTHER VCR	CHECK/REPLACE C416
GE	VG4218	N/A	ERRATIC FAST FORWARD OPERATION - UNIT MAY NOT PLAY,SEARCH FORWARD OR FFWD - DOES MOVE IN REVIEW/REWIND - EATS TAPES	CHECK/REPLACE Q512 FOR LEAKAGE (CAPSTAN SWITCH)
GE	VG4218	N/A	WILL NOT ACCEPT TAPE - 12 VOLTS ON LOADING IC MISSING	CHECK/REPLACE D001 (33 VOLT ZENER)
GE	VG4218	N/A	NO VIDEO ON PLAYBACK OR RECORD - AUDIO NORMAL	CHECK/REPLACE Q645
GE	VG4218	N/A	NO VIDEO ON PLAYBACK OR RECORD - AUDIO NORMAL	CHECK/REPLACE Q645
GE	VG4218	N/A	NO AUDI ON SELF-RECORDED TAPES	CHECK/REPLACE Z901
GE	VG4218	N/A	NO VIDEO ON PLAYBACK OR RECORD - AUDIO NORMAL	CHECK/REPLACE Q645
GE	VG4218	N/A	WILL NOT ACCEPT TAPE - 12 VOLTS ON LOADING IC MISSING	CHECK/REPLACE D001 (33 VOLT ZENER)
GE	VG4218	N/A	WILL NOT RECORD AUDIO - PLAYBACK AUDIO/VIDEO ARE FINE	CHECK/REPLACE Z901 CIRCUIT PROTECTOR
GE	VG4218	N/A	DEAD - SOMETIMES PART OF DISPLAY WILL LIGHT AND SOMETIMES THE DRUM MOTOR WILL TRY TO START	CHECK/REPLACE Z611 LEAKY
GE	VG4218	N/A	WILL NOT RECORD AUDIO BUT VIDEO IS OK	CHECK/REPLACE Z901
GE	VG4218	N/A	ERRATIC FAST FORWARD OPERATION - UNIT MAY NOT PLAY,SEARCH FORWARD OR FFWD - DOES MOVE IN REVIEW/REWIND - EATS TAPES	CHECK/REPLACE Q512 FOR LEAKAGE (CAPSTAN SWITCH)
GE	VG4219	N/A	WILL NOT POWER OFF AFTER A XPR RECORDING SESSION - GOES TO STOP AND REMAINS POWERED ON	CHECK/REPLACE IC01 WITH NEW TYPE (P/N# 211943)
GE	VG4219	N/A	MECHANISM JAMS WHEN LOADING TAPE AROUND CYLINDER	CHECK/REPLACE LEVER K128 (P/N# 212321) WITH NEW TYPE - ALSO CHECK CAM GEAR FOR DAMAGED TEETH
GE	VG4219	N/A	INTERMITTENT RECORDING OF LINEAR AUDIO - OLD AUDIO NOT BEING ERASED	CHANGE C722 TO 0.01uF (P/N# 174423), SHORT EITHER R724 OR R725, CHANGE R722 TO A 18k (P/N# 174366)
GE	VG4219	N/A	FULL OSD IS NOT DISPLAYED WHEN CASSETTE TAPE IS IN VCR	CHECK/REPLACE IC01 WITH NEW TYPE (P/N# 211943)
GE	VG4230	N/A	UNSTABLE OR WAVING PICTURE WHEN USING THE VCR'S RF CONVERTER	CHANGE R7005 TO A 200 1/4w. RESISTOR
GE	VG4230	N/A	TAPE SLACK OCCURS WHEN GOING FROM F/F OR REW TO STOP MODE	CHECK/REPLACE 'T' BRAKE SPRING (P/N# 228959)
GE	VG4232	N/A	TAPE SLACK OCCURS WHEN GOING FROM F/F OR REW TO STOP MODE	CHECK/REPLACE 'T' BRAKE SPRING (P/N# 228959)
GE	VG4232	N/A	UNSTABLE OR WAVING PICTURE WHEN USING THE VCR'S RF CONVERTER	CHANGE R7005 TO A 200 1/4w. RESISTOR
GE	VG4233	N/A	TAPE SLACK OCCURS WHEN GOING FROM F/F OR REW TO STOP MODE	CHECK/REPLACE 'T' BRAKE SPRING (P/N# 228959)
GE	VG4233	N/A	UNSTABLE OR WAVING PICTURE WHEN USING THE VCR'S RF CONVERTER	CHANGE R7005 TO A 200 1/4w. RESISTOR
GE	VG4235	N/A	PLAYBACK SPEED INCORRECT OR DISPLAY INDICATES THE WRONG SPEED	IF CAPSTAN MOTOR HAS BEEN REPLACED, BE SURE IT IS THE CORRECT TYPE - SHOULD BE (P/N# 220990)
GE	VG4238	N/A	NO COLOR IN LP SEARCH	THIS IS NOT A MALFUNCTION BUT A DESIGN CHARACTERISTIC
GE	VG4238	N/A	FRONT PANEL TRACKING BUTTONS INOPERATIVE	THESE BUTTONS CANNOT BE HELD DOWN - THEY HAVE TO BE PRESSED AND RELEASED REPEATEDLY
GE	VG4239	N/A	NO COLOR IN LP SEARCH	THIS IS NOT A MALFUNCTION BUT A DESIGN CHARACTERISTIC
GE	VG4239	N/A	FLUORESCENT DISPLAY FLASHES INTERMITTENTLY ONLY WHEN THE UNIT IS IN THE OFF MODE - MAY GO FROM TIME DISPLAY TO --:--	ADD INTERRUPT CBA (P/N# 233213)
GE	VG4239	N/A	FRONT PANEL TRACKING BUTTONS INOPERATIVE	THESE BUTTONS CANNOT BE HELD DOWN - THEY HAVE TO BE PRESSED AND RELEASED REPEATEDLY
GE	VG4239	N/A	FLUORESCENT DISPLAY FLASHES INTERMITTENTLY ONLY WHEN THE UNIT IS IN THE OFF MODE - MAY GO FROM TIME DISPLAY TO --:--	CHECK/REPLACE IC501 (P/N# 229329)
GE	VG4255	N/A	CASSETTE TAPE DOES NOT SLOW DOWN AT THE END OF HIGH SPEED REWIND	CHECK/REPLACE DIODE LOCATED ON THE EMITTER LEG OF Q202
GE	VG4255	N/A	VCR TURNS OFF AFTER POWERED ON OR UNIT HAS EXCESSIVE DRUM SPEED	CHECK/RESOLDER CONNECTIONS ON 6 PIN POWER CONNECTOR TO THE DRUM MOTOR -- THIS CONNECTOR IS SURFACE MOUNTED
GE	VG4255	N/A	DISTORTED/GARBLED LINEAR AUDIO DURING SLP PLAYBACK ONLY	CHECK/REPLACE IC601 (P/N# 231932) WITH NEW TYPE
GE	VG4255	N/A	MISSING MENU ITEMS SUCH AS VCR PLUS AND HI-FI AUDIO OPTIONS - CUSTOMER UNABLE TO USE VCR PLUS	REMOVE D718,D719,D720 - ADD D707 AND D709 (P/N# 198589) TO OP. CBA-D707 CATH TO CATH OF D708, D707 ANODE TO D709 ANODE
GE	VG4255	N/A	WAVY PICTURE ON PLAYBACK OR SQUEAL FROM CAPSTAN MOTOR	CHECK/REPLACE FELT PAD UNDER THE CAPSTAN MOTOR (P/N 233964)
GE	VG7500	N/A	WILL NOT ERASE PREVIOUSLY RECORDED AUDIO - LINES IN THE PICTURE	CHECK/REPLACE Q504 (2SD261 OR ECG123AP)
GE	VG7500	N/A	WILL NOT LOAD TAPE AND MISSING 15 VOLTS FROM POWER SUPPLY	CHECK FOR COLD SOLDER JOINTS ON POWER SUPPLY BOARD NEAR THE HEAT DINK MOUNTED REGULATOR TRANSISTORS.
GE	VG7500	N/A	INTERMITTENT RECORDING OF AUDIO	CHECK/RESOLDER CONNECTIONS ON CN501
GE	VG7500	N/A	INSERT TAPE,MACHINE LOADS TAPE AROUND HEADS BUT NO MOTORS ARE RUNNING,THEN UNLOADS LEAVING TAPE HANGING FROM TAPE.	CHECK/CLEAN MODE SELECT SWITCH
GE	VG7500	N/A	Q501 FAILS-EVEN AFTER BIAS OSC. KIT WAS INSTALLED	CHECK FOR BROKEN LEADS ON C501 AND Q501
GE	VG7500	N/A	RECORDING GOES TO SNOW - E-E DISTORTED	CHECK/RESOLDER CONNECTIONS ON Q105
GE	VG7500	N/A	GOES TO STOP AFTER 3 SECONDS WHENN RECORDING - PLAYBACK OK	CHECK/RESOLDER CONNECTIONS ON Q105 AND Q109
GE	VG7500	N/A	WILL NOT PLAY/FF/REW IF ERASE TAB IS IN PLACE	CHECK IC206
GE	VG7500	N/A	MACHINE RUNS TOO FAST IN PLAYBACK	CHECK/REPLACE IC601
GE	VG7500	N/A	LOW VOLUME ON TUNER BUT PLAYS A TAPE FINE	CHECK/REPLACE IC0401 (LOW OUTPUT ON FM DETECTOR)
GE	VG7500	N/A	RECORD/PLAY WERE FINE IN SP-BUT IN LP/SLP THE CAPSTAN SPEED WOULD RUN FAST.	CHECK Q205 FOR LEAKAGE
GE	VG7500	N/A	SNOWY PIX ON ALL CHANNELS	CHECK Q406
GE	VG7500	N/A	POOR AUDIO - WARBLE IN AUDIO - INTERMITTENT - MAY TAKE AN HOUR OR SO TO SHOW UP.	CHECK C215 OR SOLDER CONNECTIONS
GE	VG7500	N/A	DEAD - NO CLOCK OR POWER - ALL SWITCHED VOLTAGES ARE MISSING BUT ALL-TIME VOLTAGES ARE PRESENT	CHECK/REPLACE C102 (2.2uF @ 50v)
GE	VG7500	N/A	NO TUNER AUDIO	CHECK C418 FOR OPEN/SHORT
GE	VG7500	N/A	SNOWY E-E MODE	CHECK/REPLACE Q54 IN RF DEMODULATOR
GE	VG7500	N/A	TAPE RECORDED IN LP SWITCHES TO EP IN PLAYBACK MODE	CHECK IC203
GE	VG7500	N/A	NO LOCK IN SLP ON PLAYBACK ONLY	CHECK IC203
GE	VG7500	N/A	AFTER WARM UP, VCR GOES INTO FAST SEARCH	CHECK/REPLACE IC206
GE	VG7500	N/A	DEAD - NO CLOCK OR POWER - ALL SWITCHED VOLTAGES ARE MISSING BUT ALL-TIME VOLTAGES ARE PRESENT	CHECK/REPLACE C102 (2.2uF @ 50v)
GE	VG7500	N/A	INSERT TAPE,MACHINE LOADS TAPE AROUND HEADS BUT NO MOTORS ARE RUNNING,THEN UNLOADS LEAVING TAPE HANGING FROM TAPE.	CHECK/CLEAN MODE SELECT SWITCH
GE	VG7500	N/A	BLANK RASTER IN THE PLAYBACK MODE-- E-E IS NORMAL	CHECK C306 FOR HIGH LEAKAGE
GE	VG7500	N/A	DRUM MOTOR WON'T RUN	CHECK XT301 (3.58MHz CRYSTAL)
GE	VG7500	N/A	EATS TAPE WHEN EJECTING	CHECK/REPLACE TAKE-UP REEL BRAKE
GE	VG7500	N/A	TAKE UP REEL TURNS THEN STOPS IN FF OR REW, STOPS AND EJECTS TAPE	CHECK/REPLACE R251 (470k)
GE	VG7500	N/A	WILL NOT PLAY - DRUM DOES NOT RUN OR MAY GO INTO FREE RUN	CHECK/RESOLDER CONNECTIONS ON Q105 AND Q106
GE	VG7500	N/A	COLOR MISSING IN PLAYBACK OR RECORD	CHECK C347 FOR OPEN
GE	VG7500	N/A	LOW VOLUME ON TUNER BUT PLAYS A TAPE FINE	CHECK/REPLACE IC0401 (LOW OUTPUT ON FM DETECTOR)
GE	VG7500	N/A	TAPE LOADS AND ALL MOTORS START THEN UNIT UNLOADS	CHECK L106 FOR HIGH RESISTANCE
GE	VG7500	N/A	NO CLOCK DISPLAY BUT UNIT DOES POWER UP AND PLAY	CHECK/RESOLDER CONNECTIONS ON PINS 1 & 2 OF CN203
GE	VG7500	N/A	WON'T TUNE STATION--ALL STATIONS LOOK SCRAMBLED	CHECK C413 FOR OPEN
GE	VG7500	N/A	POOR AUDIO - WARBLE IN AUDIO - INTERMITTENT - MAY TAKE AN HOUR OR SO TO SHOW UP.	CHECK C215 OR SOLDER CONNECTIONS
GE	VG7500	N/A	SHUTS OFF ON RECORD INTERMITTENT-SOMETIMES VCR WILL KICK THE TAPE OUT.	CHECK/CLEAN THE ERASE PROTECT SWITCH
GE	VG7510	N/A	WILL NOT SWITCH FROM TV/VCR--12VOLT REGULATED SUPPLY IS LOW	CHECK/REPLACE Q1201 AND Q1202 FOR SHORT OR LEAKY
GE	VG7510	N/A	SCREEN GOES BLACK WHEN PROGRAM BUTTON ON REMOTE IS PUSHED TO SET CLOCK.	CHECK/REPLACE IC3003
GE	VG7510	N/A	WILL NOT REWIND - MECHANICAL PROBLEM - MAY BE INTERMITTENT	CHECK/REPLACE SUB LEVER ASSEMBLY (VMMS0042)
GE	VG7510	N/A	ONLY REWINDS WHEN POWERED UP	CHECK FOR OPEN SOLENOID (PS00029)
GE	VG7510	N/A	WILL NOT REWIND AND EATS TAPES ON PLAYBACK	EXAMINE THE GEAR DIRECTLY BELOW MAIN DRIVE PULLEY. THIS IS ITEM# 141 ON THE BREAK DOWN.
GE	VG7510	N/A	BREAK LIFTER ARM WHEN UNLOADING	CHECK FOR BENT METAL TAPE FLAP OPENER (RIGHT FRONT
GE	VG7510	N/A	GOOD BLACK AND WHITE PIX DURING PLAYBACK BUT NO COLOR	CHECK TO SEE IF COMB FILTER IS INSTALLED PROPERLY
GE	VG7510	N/A	ONLY REWINDS WHEN POWERED UP	CHECK FOR OPEN SOLENOID (PS00029)
GE	VG7510	N/A	INTERMITTENTLY GOES TO BLUE SCRN.--REW/FF SCAN PIX IS OK	CHECK FOR DEFECTIVE C2014 OR C2015 OR SOLDER CONNECTIONS ON EITHER.
GE	VG7510	N/A	ERRATIC OPERATION-LOADS TAPE IN VCR THEN NOTHING-MAY BEGIN TO PLAY TAPE AND JUST STOP BUT STAYS LOADED	CHECK/REPLACE MODE SWITCH ON RIGHT SIDE OF CASSETTE HOUSING AND HARD WIRE 4 WIRE PLUG CONNECTION.
GE	VG7510	N/A	NO TUNER VIDEO IN VCR MODE - NO OSD - NO UNSWITCHED 5 VOLTS	CHECK/REPLACE L7001 FOR OPEN
GE	VG7510	N/A	VCR TURNS ON BUT ALL FUNCTIONS INOPERATIVE--DEW LIGHT ON	CHECK FOR COLD SOLDER CONNECTIONS BETWEEN PINS 2&5 OF SYSTEM CTRL. uPROC. (IC6001)
GE	VG7510	N/A	BREAKS LIFTER ARM WHEN UNLOADING TAPE--LOADS OK	CHECK FOR BENT TAPE FLAP OPENER (RIGHT FRONT CORNER
GE	VG7510	N/A	ERRATIC OPERATION-LOADS TAPE IN VCR THEN NOTHING-MAY BEGIN TO PLAY TAPE AND JUST STOP BUT STAYS LOADED	CHECK/REPLACE MODE SWITCH ON RIGHT SIDE OF CASSETTE HOUSING AND HARD WIRE 4 WIRE PLUG CONNECTION.
GE	VG7510	N/A	BLOWS AC LINE FUSE IMMEDIATELY	CHECK F1001,D1001,C1004,Q1001,Q1002,D1015,D1005
GE	VG7510	N/A	SOLENOID WON'T PULL IN AND SOLENOID ITSELF IS FINE	CHECK/REPLACE Q6005 FOR OPEN
GE	VG7510	N/A	BLOWS AC LINE FUSE IMMEDIATELY	CHECK F1001,D1001,C1004,Q1001,Q1002,D1015,D1005
GE	VG7510	N/A	DEW INDICATOR IS ON BUT VCR HAS NO DEW SENSOR	CHECK THE GROUND TO THE DEW INPUT (PIN 77) ON THE MICROPROCESSOR (IC6001)
GE	VG7510	N/A	LOW VOLUME ON TUNER BUT PLAYS A TAPE FINE	CHECK/REPLACE IC0401 (LOW OUTPUT ON FM DETECTOR)
GE	VG7510	G LOAD	SOLENOID FAILURE	CAUSED BY A NOISY MODE SELECT SWITCH - INSTALL KIT# 190130 WHICH INCLUDES INSTRUCTIONS.
GE	VG7515	N/A	NOISY VIDEO,NOISE BANDS OR STREAKS IN PLAYBACK VIDEO	REMOVE VIDEO HEAD AND INSTALL (2) LOCK WASHERS (210807) ON SCREWS LOCATED UNDER DRUM.
GE	VG7515	N/A	NO VIDEO BUT OSD WORKS NORMALLY	CHECK C317 FOR LEAKAGE
GE	VG7515	N/A	INSERT TAPE,MACHINE LOADS TAPE AROUND HEADS BUT NO MOTORS ARE RUNNING,THEN UNLOADS LEAVING TAPE HANGING FROM TAPE.	CHECK/CLEAN MODE SELECT SWITCH
GE	VG7515	N/A	NOISY VIDEO,NOISE BANDS OR STREAKS IN PLAYBACK VIDEO	REMOVE VIDEO HEAD AND INSTALL (2) LOCK WASHERS (210807) ON SCREWS LOCATED UNDER DRUM.
GE	VG7515	N/A	SHUTS OFF ON RECORD INTERMITTENT-SOMETIMES VCR WILL KICK THE TAPE OUT.	CHECK/CLEAN THE ERASE PROTECT SWITCH
GE	VG7515	N/A	NO VIDEO BUT OSD WORKS NORMALLY	CHECK C317 FOR LEAKAGE
GE	VG7515	N/A	SHUTS OFF ON RECORD INTERMITTENT-SOMETIMES VCR WILL KICK THE TAPE OUT.	CHECK/CLEAN THE ERASE PROTECT SWITCH
GE	VG7515	N/A	CAPSTAN HAS INTERMITTENT SPEED CONTROL	CHECK/RESOLDER CONNECTIONS ON PATH BETWEEN IC601 PIN 26 AND R611
GE	VG7515	N/A	FRONT PANEL LOCKS UP - LOSS OF REMOTE OPERATION - MAY BE INTERMITTENT.	CHECK IC0601-IF THE TYPE NUMBER IS NOT UPD75116CW-091 THEN REPLACE WITH 195143-CHECK ALSO IR RECVR.192280
GE	VG7515	N/A	AUDIO MISSING IN PLAYBACK--NOT ERASING OLD AUDIO	CHECK IC601
GE	VG7515	N/A	FRONT PANEL LOCKS UP - LOSS OF REMOTE OPERATION - MAY BE INTERMITTENT.	CHECK IC0601-IF THE TYPE NUMBER IS NOT UPD75116CW-091 THEN REPLACE WITH 195143-CHECK ALSO IR RECVR.192280
GE	VG7515	N/A	NOISY VIDEO,NOISE BANDS OR STREAKS IN PLAYBACK VIDEO	REMOVE VIDEO HEAD AND INSTALL (2) LOCK WASHERS (210807) ON SCREWS LOCATED UNDER DRUM.
GE	VG7515	N/A	DEAD SET	CHECK IC701 AND R705
GE	VG7515	N/A	CAPSTAN HAS INTERMITTENT SPEED CONTROL	CHECK/RESOLDER CONNECTIONS ON PATH BETWEEN IC601 PIN 26 AND R611
GE	VG7515	N/A	INSERT TAPE,MACHINE LOADS TAPE AROUND HEADS BUT NO MOTORS ARE RUNNING,THEN UNLOADS LEAVING TAPE HANGING FROM TAPE.	CHECK/CLEAN MODE SELECT SWITCH
GE	VG7515	N/A	INSERT TAPE,MACHINE LOADS TAPE AROUND HEADS BUT NO MOTORS ARE RUNNING,THEN UNLOADS LEAVING TAPE HANGING FROM TAPE.	CHECK/CLEAN MODE SELECT SWITCH
GE	VG7515	N/A	AUDIO MISSING IN PLAYBACK--NOT ERASING OLD AUDIO	CHECK IC601
GE	VG7515	N/A	FRONT PANEL LOCKS UP - LOSS OF REMOTE OPERATION - MAY BE INTERMITTENT.	CHECK IC0601-IF THE TYPE NUMBER IS NOT UPD75116CW-091 THEN REPLACE WITH 195143-CHECK ALSO IR RECVR.192280
GE	VG7515	N/A	NO E-E,RECORD INOPER.,AUTO PROG. INOPER.--PLAYBACK IS OK	CHECK IC904
GE	VG7515	N/A	GARBLED AUDIO	CHECK Q0501,R0501,C0502,L0501
GE	VG7515	N/A	FUZZY PICTURE ON TAPE OR TUNER - NO RECORD AUDIO OR PB	CHECK/REPLACE IC501,Q501 AND L0501
GE	VG7515	N/A	GARBLED AUDIO	CHECK Q0501,R0501,C0502,L0501
GE	VG7520	N/A	SOLENOID WON'T PULL IN AND SOLENOID ITSELF IS FINE	CHECK/REPLACE Q6005 FOR OPEN
GE	VG7520	N/A	WILL NOT RECORD VIDEO OR SOUND	CHECK/REPLACE Q4002 AND T4001
GE	VG7520	N/A	WILL NOT SWITCH FROM TV/VCR--12VOLT REGULATED SUPPLY IS LOW	CHECK/REPLACE Q1201 AND Q1202 FOR SHORT OR LEAKY
GE	VG7520	N/A	ERRATIC OPERATION-LOADS TAPE IN VCR THEN NOTHING-MAY BEGIN TO PLAY TAPE AND JUST STOP BUT STAYS LOADED	CHECK/REPLACE MODE SWITCH ON RIGHT SIDE OF CASSETTE HOUSING AND HARD WIRE 4 WIRE PLUG CONNECTION.
GE	VG7520	G LOAD	SOLENOID FAILURE	CAUSED BY A NOISY MODE SELECT SWITCH - INSTALL KIT# 190130 WHICH INCLUDES INSTRUCTIONS.
GE	VG7575	N/A	NOISY VIDEO,NOISE BANDS OR STREAKS IN PLAYBACK VIDEO	REMOVE VIDEO HEAD AND INSTALL (2) LOCK WASHERS (210807) ON SCREWS LOCATED UNDER DRUM.
GE	VG7575	N/A	VCR INOPERATIVE-NO CLOCK-NO LED'S-CAPSTAN MOTOR RUNNING VERY SLOWLY-NO FUNCTIONS WORK	CHECK C107 FOR OPEN
GE	VG7575	N/A	SHUTS OFF ON RECORD INTERMITTENT-SOMETIMES VCR WILL KICK THE TAPE OUT.	CHECK/CLEAN THE ERASE PROTECT SWITCH
GE	VG7575	N/A	PLAYS BACK A PRE-RECORDED TAPE FINE BUT PLAYBACK OF A RECORDING IS ALL SNOW	CHECK/REPLACE L0301 FOR SHORT
GE	VG7575	N/A	COLOR IS MISSING-ALL OTHER FUNCTIONS OK	CHECK C0345 FOR LEAKAGE
GE	VG7575	N/A	FRONT PANEL LOCKS UP - LOSS OF REMOTE OPERATION - MAY BE INTERMITTENT.	CHECK IC0601-IF THE TYPE NUMBER IS NOT UPD75116CW-091 THEN REPLACE WITH 195143-CHECK ALSO IR RECVR.192280
GE	VG7575	N/A	NOISY VIDEO,NOISE BANDS OR STREAKS IN PLAYBACK VIDEO	REMOVE VIDEO HEAD AND INSTALL (2) LOCK WASHERS (210807) ON SCREWS LOCATED UNDER DRUM.
GE	VG7575	N/A	INSERT TAPE,MACHINE LOADS TAPE AROUND HEADS BUT NO MOTORS ARE RUNNING,THEN UNLOADS LEAVING TAPE HANGING FROM TAPE.	CHECK/CLEAN MODE SELECT SWITCH
GE	VG7575	N/A	INSERT TAPE,MACHINE LOADS TAPE AROUND HEADS BUT NO MOTORS ARE RUNNING,THEN UNLOADS LEAVING TAPE HANGING FROM TAPE.	CHECK/CLEAN MODE SELECT SWITCH
GE	VG7575	N/A	NO VIDEO IN VCR E-E OR PLAYBACK	CHECK C0317 FOR SHORTS
GE	VG7575	N/A	LOW VOLUME ON TUNER BUT PLAYS A TAPE FINE	CHECK/REPLACE IC0401 (LOW OUTPUT ON FM DETECTOR)
GE	VG7575	N/A	FRONT PANEL LOCKS UP - LOSS OF REMOTE OPERATION - MAY BE INTERMITTENT.	CHECK IC0601-IF THE TYPE NUMBER IS NOT UPD75116CW-091 THEN REPLACE WITH 195143-CHECK ALSO IR RECVR.192280
GE	VG7610	N/A	ONLY REWINDS WHEN POWERED UP	CHECK FOR OPEN SOLENOID (PS00029)
GE	VG7610	N/A	SOLENOID WON'T PULL IN AND SOLENOID ITSELF IS FINE	CHECK/REPLACE Q6005 FOR OPEN
GE	VG7610	N/A	BREAK LIFTER ARM WHEN UNLOADING	CHECK FOR BENT METAL TAPE FLAP OPENER (RIGHT FRONT
GE	VG7610	N/A	WILL NOT REWIND AND EATS TAPES ON PLAYBACK	EXAMINE THE GEAR DIRECTLY BELOW MAIN DRIVE PULLEY. THIS IS ITEM# 141 ON THE BREAK DOWN.
GE	VG7610	N/A	SCREEN GOES BLACK WHEN PROGRAM BUTTON ON REMOTE IS PUSHED TO SET CLOCK.	CHECK/REPLACE IC3003
GE	VG7610	N/A	WILL NOT REWIND - MECHANICAL PROBLEM - MAY BE INTERMITTENT	CHECK/REPLACE SUB LEVER ASSEMBLY (VMMS0042)
GE	VG7610	N/A	INTERMITTENTLY GOES TO BLUE SCRN.--REW/FF SCAN PIX IS OK	CHECK FOR DEFECTIVE C2014 OR C2015 OR SOLDER CONNECTIONS ON EITHER.
GE	VG7610	N/A	DEW INDICATOR IS ON BUT VCR HAS NO DEW SENSOR	CHECK THE GROUND TO THE DEW INPUT (PIN 77) ON THE MICROPROCESSOR (IC6001)
GE	VG7610	N/A	ERRATIC OPERATION-LOADS TAPE IN VCR THEN NOTHING-MAY BEGIN TO PLAY TAPE AND JUST STOP BUT STAYS LOADED	CHECK/REPLACE MODE SWITCH ON RIGHT SIDE OF CASSETTE HOUSING AND HARD WIRE 4 WIRE PLUG CONNECTION.
GE	VG7610	N/A	NO TUNER VIDEO IN VCR MODE - NO OSD - NO UNSWITCHED 5 VOLTS	CHECK/REPLACE L7001 FOR OPEN
GE	VG7610	N/A	BLOWS AC LINE FUSE IMMEDIATELY	CHECK F1001,D1001,C1004,Q1001,Q1002,D1015,D1005
GE	VG7610	N/A	ERRATIC OPERATION-LOADS TAPE IN VCR THEN NOTHING-MAY BEGIN TO PLAY TAPE AND JUST STOP BUT STAYS LOADED	CHECK/REPLACE MODE SWITCH ON RIGHT SIDE OF CASSETTE HOUSING AND HARD WIRE 4 WIRE PLUG CONNECTION.
GE	VG7610	N/A	WILL NOT SWITCH FROM TV/VCR--12VOLT REGULATED SUPPLY IS LOW	CHECK/REPLACE Q1201 AND Q1202 FOR SHORT OR LEAKY
GE	VG7610	G LOAD	SOLENOID FAILURE	CAUSED BY A NOISY MODE SELECT SWITCH - INSTALL KIT# 190130 WHICH INCLUDES INSTRUCTIONS.
GE	VG7615	N/A	NOISY VIDEO,NOISE BANDS OR STREAKS IN PLAYBACK VIDEO	REMOVE VIDEO HEAD AND INSTALL (2) LOCK WASHERS (210807) ON SCREWS LOCATED UNDER DRUM.
GE	VG7620	N/A	SOLENOID WON'T PULL IN AND SOLENOID ITSELF IS FINE	CHECK/REPLACE Q6005 FOR OPEN
GE	VG7620	N/A	INTERMITTENTLY WON'T EJECT OR COME ON IN PROGRAM MODE AND OCCASIONALLY WON'T SHUT OFF	CHECK/RESOLDER CONNECTIONS ON CABLE FROM BASKET TO MAIN PCB
GE	VG7620	N/A	ERRATIC OPERATION-LOADS TAPE IN VCR THEN NOTHING-MAY BEGIN TO PLAY TAPE AND JUST STOP BUT STAYS LOADED	CHECK/REPLACE MODE SWITCH ON RIGHT SIDE OF CASSETTE HOUSING AND HARD WIRE 4 WIRE PLUG CONNECTION.
GE	VG7620	G LOAD	SOLENOID FAILURE	CAUSED BY A NOISY MODE SELECT SWITCH - INSTALL KIT# 190130 WHICH INCLUDES INSTRUCTIONS.
GE	VG7675	N/A	NOISY VIDEO,NOISE BANDS OR STREAKS IN PLAYBACK VIDEO	REMOVE VIDEO HEAD AND INSTALL (2) LOCK WASHERS (210807) ON SCREWS LOCATED UNDER DRUM.
GE	VG7685	N/A	ERRATIC OPERATION-LOADS TAPE IN VCR THEN NOTHING-MAY BEGIN TO PLAY TAPE AND JUST STOP BUT STAYS LOADED	CHECK/REPLACE MODE SWITCH ON RIGHT SIDE OF CASSETTE HOUSING AND HARD WIRE 4 WIRE PLUG CONNECTION.
GE	VG7685	N/A	SOLENOID WON'T PULL IN AND SOLENOID ITSELF IS FINE	CHECK/REPLACE Q6005 FOR OPEN
GE	VG7685	G LOAD	SOLENOID FAILURE	CAUSED BY A NOISY MODE SELECT SWITCH - INSTALL KIT# 190130 WHICH INCLUDES INSTRUCTIONS.
GE	VG7720	N/A	WILL EJECT TAPE AT THE END OF REWINDING AND ATTEMPT TO LOAD TAPE AGAIN, THEN POWER SHUTS OFF	CHECK/REPLACE MODE SELECT SWITCH
GE	VG7720	N/A	SOLENOID WON'T PULL IN AND SOLENOID ITSELF IS FINE	CHECK/REPLACE Q6005 FOR OPEN
GE	VG7720	N/A	ERRATIC OPERATION-LOADS TAPE IN VCR THEN NOTHING-MAY BEGIN TO PLAY TAPE AND JUST STOP BUT STAYS LOADED	CHECK/REPLACE MODE SWITCH ON RIGHT SIDE OF CASSETTE HOUSING AND HARD WIRE 4 WIRE PLUG CONNECTION.
GE	VG7720	G LOAD	SOLENOID FAILURE	CAUSED BY A NOISY MODE SELECT SWITCH - INSTALL KIT# 190130 WHICH INCLUDES INSTRUCTIONS.
GE	VG7725	N/A	ERRATIC OPERATION-LOADS TAPE IN VCR THEN NOTHING-MAY BEGIN TO PLAY TAPE AND JUST STOP BUT STAYS LOADED	CHECK/REPLACE MODE SWITCH ON RIGHT SIDE OF CASSETTE HOUSING AND HARD WIRE 4 WIRE PLUG CONNECTION.
GE	VG7725	N/A	WILL NOT POWER UP (TAPE STUCK)	CHECK/REPLACE C1013,C1014,C1015 AND C1016
GE	VG7725	N/A	SOLENOID WON'T PULL IN AND SOLENOID ITSELF IS FINE	CHECK/REPLACE Q6005 FOR OPEN
GE	VG7725	N/A	DEAD - NO DISPLAY OR POWER	CHECK/REPLACE C1015,C1016, C1018 AND C1019
GE	VG7725	G LOAD	SOLENOID FAILURE	CAUSED BY A NOISY MODE SELECT SWITCH - INSTALL KIT# 190130 WHICH INCLUDES INSTRUCTIONS.
GE	VG7775	N/A	ERRATIC OPERATION-LOADS TAPE IN VCR THEN NOTHING-MAY BEGIN TO PLAY TAPE AND JUST STOP BUT STAYS LOADED	CHECK/REPLACE MODE SWITCH ON RIGHT SIDE OF CASSETTE HOUSING AND HARD WIRE 4 WIRE PLUG CONNECTION.
GE	VG7775	N/A	SOLENOID WON'T PULL IN AND SOLENOID ITSELF IS FINE	CHECK/REPLACE Q6005 FOR OPEN
GE	VG7775	G LOAD	SOLENOID FAILURE	CAUSED BY A NOISY MODE SELECT SWITCH - INSTALL KIT# 190130 WHICH INCLUDES INSTRUCTIONS.
GE	VG7785	N/A	ERRATIC OPERATION-LOADS TAPE IN VCR THEN NOTHING-MAY BEGIN TO PLAY TAPE AND JUST STOP BUT STAYS LOADED	CHECK/REPLACE MODE SWITCH ON RIGHT SIDE OF CASSETTE HOUSING AND HARD WIRE 4 WIRE PLUG CONNECTION.
GE	VG7785	N/A	WILL NOT POWER UP (TAPE STUCK)	CHECK/REPLACE C1013,C1014,C1015 AND C1016
GE	VG7785	N/A	SOLENOID WON'T PULL IN AND SOLENOID ITSELF IS FINE	CHECK/REPLACE Q6005 FOR OPEN
GE	VG7785	N/A	DEAD - POWER SUPPLY SQUEALS - VOLTAGES TOO HIGH	CHECK/REPLACE C1021 IN POWER SUPPLY OPEN
GE	VG7785	G LOAD	SOLENOID FAILURE	CAUSED BY A NOISY MODE SELECT SWITCH - INSTALL KIT# 190130 WHICH INCLUDES INSTRUCTIONS.
GE	VG7795	N/A	ERRATIC OPERATION-LOADS TAPE IN VCR THEN NOTHING-MAY BEGIN TO PLAY TAPE AND JUST STOP BUT STAYS LOADED	CHECK/REPLACE MODE SWITCH ON RIGHT SIDE OF CASSETTE HOUSING AND HARD WIRE 4 WIRE PLUG CONNECTION.
GE	VG7795	N/A	SOLENOID WON'T PULL IN AND SOLENOID ITSELF IS FINE	CHECK/REPLACE Q6005 FOR OPEN
GE	VG7795	G LOAD	SOLENOID FAILURE	CAUSED BY A NOISY MODE SELECT SWITCH - INSTALL KIT# 190130 WHICH INCLUDES INSTRUCTIONS.
GE	VG7910	N/A	BREAK LIFTER ARM WHEN UNLOADING	CHECK FOR BENT METAL TAPE FLAP OPENER (RIGHT FRONT
GE	VG7910	N/A	ONLY REWINDS WHEN POWERED UP	CHECK FOR OPEN SOLENOID (PS00029)
GE	VG7910	N/A	ERRATIC OPERATION-LOADS TAPE IN VCR THEN NOTHING-MAY BEGIN TO PLAY TAPE AND JUST STOP BUT STAYS LOADED	CHECK/REPLACE MODE SWITCH ON RIGHT SIDE OF CASSETTE HOUSING AND HARD WIRE 4 WIRE PLUG CONNECTION.
GE	VG7910	N/A	SCREEN GOES BLACK WHEN PROGRAM BUTTON ON REMOTE IS PUSHED TO SET CLOCK.	CHECK/REPLACE IC3003
GE	VG7910	N/A	WILL NOT REWIND - MECHANICAL PROBLEM - MAY BE INTERMITTENT	CHECK/REPLACE SUB LEVER ASSEMBLY (VMMS0042)
GE	VG7910	N/A	BLOWS AC LINE FUSE IMMEDIATELY	CHECK F1001,D1001,C1004,Q1001,Q1002,D1015,D1005
GE	VG7910	N/A	NO TUNER VIDEO IN VCR MODE - NO OSD - NO UNSWITCHED 5 VOLTS	CHECK/REPLACE L7001 FOR OPEN
GE	VG7910	N/A	DEW INDICATOR IS ON BUT VCR HAS NO DEW SENSOR	CHECK THE GROUND TO THE DEW INPUT (PIN 77) ON THE MICROPROCESSOR (IC6001)
GE	VG7910	N/A	WILL NOT SWITCH FROM TV/VCR--12VOLT REGULATED SUPPLY IS LOW	CHECK/REPLACE Q1201 AND Q1202 FOR SHORT OR LEAKY
GE	VG7910	N/A	ERRATIC OPERATION-LOADS TAPE IN VCR THEN NOTHING-MAY BEGIN TO PLAY TAPE AND JUST STOP BUT STAYS LOADED	CHECK/REPLACE MODE SWITCH ON RIGHT SIDE OF CASSETTE HOUSING AND HARD WIRE 4 WIRE PLUG CONNECTION.
GE	VG7910	N/A	WILL NOT REWIND AND EATS TAPES ON PLAYBACK	EXAMINE THE GEAR DIRECTLY BELOW MAIN DRIVE PULLEY. THIS IS ITEM# 141 ON THE BREAK DOWN.
GE	VG7910	N/A	SOLENOID WON'T PULL IN AND SOLENOID ITSELF IS FINE	CHECK/REPLACE Q6005 FOR OPEN
GE	VG7910	N/A	INTERMITTENTLY GOES TO BLUE SCRN.--REW/FF SCAN PIX IS OK	CHECK FOR DEFECTIVE C2014 OR C2015 OR SOLDER CONNECTIONS ON EITHER.
GE	VG7910	G LOAD	SOLENOID FAILURE	CAUSED BY A NOISY MODE SELECT SWITCH - INSTALL KIT# 190130 WHICH INCLUDES INSTRUCTIONS.
GE	VG7920	N/A	SOLENOID WON'T PULL IN AND SOLENOID ITSELF IS FINE	CHECK/REPLACE Q6005 FOR OPEN
GE	VG7920	N/A	ERRATIC OPERATION-LOADS TAPE IN VCR THEN NOTHING-MAY BEGIN TO PLAY TAPE AND JUST STOP BUT STAYS LOADED	CHECK/REPLACE MODE SWITCH ON RIGHT SIDE OF CASSETTE HOUSING AND HARD WIRE 4 WIRE PLUG CONNECTION.
GE	VG7920	G LOAD	SOLENOID FAILURE	CAUSED BY A NOISY MODE SELECT SWITCH - INSTALL KIT# 190130 WHICH INCLUDES INSTRUCTIONS.
GE	VG7925	N/A	SOLENOID WON'T PULL IN AND SOLENOID ITSELF IS FINE	CHECK/REPLACE Q6005 FOR OPEN
GE	VG7925	N/A	ERRATIC OPERATION-LOADS TAPE IN VCR THEN NOTHING-MAY BEGIN TO PLAY TAPE AND JUST STOP BUT STAYS LOADED	CHECK/REPLACE MODE SWITCH ON RIGHT SIDE OF CASSETTE HOUSING AND HARD WIRE 4 WIRE PLUG CONNECTION.
GE	VG7925	G LOAD	SOLENOID FAILURE	CAUSED BY A NOISY MODE SELECT SWITCH - INSTALL KIT# 190130 WHICH INCLUDES INSTRUCTIONS.
GE	VG7975	N/A	ERRATIC OPERATION-LOADS TAPE IN VCR THEN NOTHING-MAY BEGIN TO PLAY TAPE AND JUST STOP BUT STAYS LOADED	CHECK/REPLACE MODE SWITCH ON RIGHT SIDE OF CASSETTE HOUSING AND HARD WIRE 4 WIRE PLUG CONNECTION.
GE	VG7975	N/A	SOLENOID WON'T PULL IN AND SOLENOID ITSELF IS FINE	CHECK/REPLACE Q6005 FOR OPEN
GE	VG7975	G LOAD	SOLENOID FAILURE	CAUSED BY A NOISY MODE SELECT SWITCH - INSTALL KIT# 190130 WHICH INCLUDES INSTRUCTIONS.
GE	VG7980	N/A	ERRATIC OPERATION-LOADS TAPE IN VCR THEN NOTHING-MAY BEGIN TO PLAY TAPE AND JUST STOP BUT STAYS LOADED	CHECK/REPLACE MODE SWITCH ON RIGHT SIDE OF CASSETTE HOUSING AND HARD WIRE 4 WIRE PLUG CONNECTION.
GE	VG7980	N/A	SOLENOID WON'T PULL IN AND SOLENOID ITSELF IS FINE	CHECK/REPLACE Q6005 FOR OPEN
GE	VG7980	G LOAD	SOLENOID FAILURE	CAUSED BY A NOISY MODE SELECT SWITCH - INSTALL KIT# 190130 WHICH INCLUDES INSTRUCTIONS.
GE	VG7985	N/A	SOLENOID WON'T PULL IN AND SOLENOID ITSELF IS FINE	CHECK/REPLACE Q6005 FOR OPEN
GE	VG7985	N/A	ERRATIC OPERATION-LOADS TAPE IN VCR THEN NOTHING-MAY BEGIN TO PLAY TAPE AND JUST STOP BUT STAYS LOADED	CHECK/REPLACE MODE SWITCH ON RIGHT SIDE OF CASSETTE HOUSING AND HARD WIRE 4 WIRE PLUG CONNECTION.
GE	VG7985	G LOAD	SOLENOID FAILURE	CAUSED BY A NOISY MODE SELECT SWITCH - INSTALL KIT# 190130 WHICH INCLUDES INSTRUCTIONS.
GOLDSTAR	GHV1210M	N/A	NO CAPSTAN SERVO LOCK	CHECK/REPLACE IC501 OR CAPACITOR AROUND IC501
GOLDSTAR	GHV1210M	N/A	COUNTER WILL NOT COUNT	MODIFY PER SERVICE BULLETIN FOR GHV-1240M (MANUAL)
GOLDSTAR	GHV1210M	N/A	LOW REEL TORQUE ONLY ON PLAY AND RECORD	TIE A 10K ACROSS R623 TO IMPROVE TORQUE
GOLDSTAR	GHV1210M	N/A	DEW INDICATOR STAYS ON AND DRUM RUNS CONSTANTLY	CHECK/REPLACE DEW SENSOR OR IC606 - SHORT DEW SENSOR LEADS TO SEE IF INDICATOR GOES OUT. IF NOT, REPLACE IC606
GOLDSTAR	GHV1233M	N/A	TAPE CURLING AT THE BOTTOM	CHECK/REPLACE CLUTCH DUE TO TOO MUCH TORQUE
GOLDSTAR	GHV1233M	N/A	COUNTER WILL NOT COUNT	MODIFY PER SERVICE BULLETIN FOR GHV-1240M (MANUAL)
GOLDSTAR	GHV1233M	N/A	UNIT GOES TO STOP MODE AFTER A FEW SECONDS	CHECK/REPLACE REEL SENSOR (P/N# 657-010A) AND CHANGE R634 TO A 1K
GOLDSTAR	GHV1240	N/A	WILL NOT POWER UP-ALSO GOES TO REWIND WHEN PLUGGED IN	CHECK/REPLACE IC501 AND IC504
GOLDSTAR	GHV1240	N/A	TRACKING PROBLEMS - PIX/SNOW/PIX/SNOW	CHECK FOR COLD SOLDER CONNECTIONS ON PLUG P2D03 AND IC203.
GOLDSTAR	GHV1240	N/A	TRACKING WILL NOT ADJUST	CHECK/REPLACE IC201
GOLDSTAR	GHV1240	N/A	ERRATIC CAPSTAN OPERATION	CHECK/RESOLDER CONNECTIONS ON PLUG P2D01,P2D02 AND P2D03
GOLDSTAR	GHV1240M	N/A	COUNTER WILL NOT COUNT	MODIFY PER SERVICE BULLETIN FOR GHV-1240M (MANUAL)
GOLDSTAR	GHV1241	N/A	TRACKING PROBLEMS - PIX/SNOW/PIX/SNOW	CHECK FOR COLD SOLDER CONNECTIONS ON PLUG P2D03 AND IC203.
GOLDSTAR	GHV1241	N/A	WILL NOT POWER UP-ALSO GOES TO REWIND WHEN PLUGGED IN	CHECK/REPLACE IC501 AND IC504
GOLDSTAR	GHV1241	N/A	ERRATIC CAPSTAN OPERATION	CHECK/RESOLDER CONNECTIONS ON PLUG P2D01,P2D02 AND P2D03
GOLDSTAR	GHV1241	N/A	TRACKING WILL NOT ADJUST	CHECK/REPLACE IC201
GOLDSTAR	GHV1243	N/A	TRACKING WILL NOT ADJUST	CHECK/REPLACE IC201
GOLDSTAR	GHV1243	N/A	TRACKING PROBLEMS - PIX/SNOW/PIX/SNOW	CHECK FOR COLD SOLDER CONNECTIONS ON PLUG P2D03 AND IC203.
GOLDSTAR	GHV1243	N/A	ERRATIC CAPSTAN OPERATION	CHECK/RESOLDER CONNECTIONS ON PLUG P2D01,P2D02 AND P2D03
GOLDSTAR	GHV1243	N/A	WILL NOT POWER UP-ALSO GOES TO REWIND WHEN PLUGGED IN	CHECK/REPLACE IC501 AND IC504
GOLDSTAR	GHV1245	N/A	TRACKING PROBLEMS - PIX/SNOW/PIX/SNOW	CHECK FOR COLD SOLDER CONNECTIONS ON PLUG P2D03 AND IC203.
GOLDSTAR	GHV1245	N/A	ERRATIC CAPSTAN OPERATION	CHECK/RESOLDER CONNECTIONS ON PLUG P2D01,P2D02 AND P2D03
GOLDSTAR	GHV1245	N/A	TRACKING WILL NOT ADJUST	CHECK/REPLACE IC201
GOLDSTAR	GHV1245	N/A	WILL NOT POWER UP-ALSO GOES TO REWIND WHEN PLUGGED IN	CHECK/REPLACE IC501 AND IC504
GOLDSTAR	GHV1250	N/A	NO AUDIO ON RECORD-BIAS OSC. WON'T START	INCREASE R426 TO A 39k--CHECK Q409 AND Q413
GOLDSTAR	GHV1250	N/A	WILL NOT POWER UP-ALSO GOES TO REWIND WHEN PLUGGED IN	CHECK/REPLACE IC501 AND IC504
GOLDSTAR	GHV1250	N/A	ERRATIC CAPSTAN OPERATION	CHECK/RESOLDER CONNECTIONS ON PLUG P2D01,P2D02 AND P2D03
GOLDSTAR	GHV1260M	N/A	DRUM MOTOR RUNS TOO SLOW FOR A FEW SECONDS THEN VCR SHUTS OFF	CHECK/RESOLDER CONNECTIONS ON DRUM MOTOR CONNECTOR
GOLDSTAR	GHV1265	N/A	WILL NOT POWER UP-ALSO GOES TO REWIND WHEN PLUGGED IN	CHECK/REPLACE IC501 AND IC504
GOLDSTAR	GHV1280	N/A	NO DRUM OR CAPSTAN OPERATION	CHECK D5A1 FOR OPEN
GOLDSTAR	GHV1280	N/A	DEAD-BLOWING FUSES	CHECK D101,F101
GOLDSTAR	GHV1280M	N/A	INTERMITTENT SNOWY PIX-LOOKS JUST LIKE A BAD HEAD OR DIRTY.	CHECK FOR COLD SOLDER JOINTS ON P3001 OF HEAD AMP
GOLDSTAR	GHV1280M	N/A	INTERMITTENT SNOWY PIX-LOOKS JUST LIKE A BAD HEAD OR DIRTY.	CHECK FOR COLD SOLDER JOINTS OR NO SOLDER ON THE INDIVIDUAL HEADS OF THE UPPER DRUM (MUST REMOVE DRUM)
GOLDSTAR	GHV1280M	N/A	EXCESSIVE WOW AND FLUTTER	CHANGE R234 TO A 180k AND R238 TO A 27k
GOLDSTAR	GHV1280Q	N/A	EXCESSIVE WOW AND FLUTTER	CHANGE R234 TO A 180k AND R238 TO A 27k
GOLDSTAR	GHV1280Q	N/A	FM DEVIATION ADJUSTMENTS ARE TOO SENSITIVE	CHANGE R309 TO A 2.7k
GOLDSTAR	GHV1285M	N/A	EXCESSIVE WOW AND FLUTTER	CHANGE R234 TO A 180k AND R238 TO A 27k
GOLDSTAR	GHV1285Q	N/A	FM DEVIATION ADJUSTMENTS ARE TOO SENSITIVE	CHANGE R309 TO A 2.7k
GOLDSTAR	GHV1285Q	N/A	EXCESSIVE WOW AND FLUTTER	CHANGE R234 TO A 180k AND R238 TO A 27k
GOLDSTAR	GHV1290	N/A	WASHED OUT VIDEO-LOW LUMINANCE LEVEL	CHECK IC302 (GOLDSTAR 669-051A)
GOLDSTAR	GHV1290M	N/A	INTERMITTENT OPERATION OF IC502	CHECK/REMOVE R517 FROM THE CIRCUIT
GOLDSTAR	GHV1290M	N/A	PICTURE FLICKERS IN THE EP MODE AND WEAK COLOR	CHANGE R329 TO A 560 ohm
GOLDSTAR	GHV1700M	N/A	ERRATIC TAPE COUNTER OPERATION	CHANGE R510 TO 18k
GOLDSTAR	GHV1700M	N/A	INTERMITTENT OPERATION OF IC502	CHECK/REMOVE R517 FROM THE CIRCUIT
GOLDSTAR	GHV1705M	N/A	ERRATIC TAPE COUNTER OPERATION	CHANGE R510 TO 18k
GOLDSTAR	GHV1705M	N/A	INTERMITTENT OPERATION OF IC502	CHECK/REMOVE R517 FROM THE CIRCUIT
GOLDSTAR	GHV1900	N/A	MANY VERTICAL BARS ON THE SCREEN THAT FLASH ON AND OFF IF THE CLOCK HASN'T BEEN SET.	CHECK/REPLACE IC801
GOLDSTAR	GHV1900M	N/A	ERRATIC TAPE COUNTER OPERATION	CHANGE R517 TO 27k
GOLDSTAR	GHV1900M	N/A	WON'T LOAD A TAPE	CHECK/REPLACE LOADING BRACKET ASSY. (P/N# 321-223A) AND IC502
GOLDSTAR	GHV1905	N/A	WILL NOT TAKE OR EJECT TAPE	CHECK/REPLACE IC502 (P/N# ECG1716 OR BA6209N)
GOLDSTAR	GHV1905M	N/A	PIX WON'T LOCK IN WHEN CHANGING CHANNELS	CHECK ALIGNMENT OF AFT CIRCUIT
GOLDSTAR	GHV1905M	N/A	ERRATIC TAPE COUNTER OPERATION	CHANGE R517 TO 27k
GOLDSTAR	GHV1905M	N/A	INTERMITTENT AUDIO IN PLAYBACK	CHECK FOR A OPEN CONNECTION BETWEEN THE INPUT OF IC401 AND THE AUDIO HEAD
GOLDSTAR	GHV1905M	N/A	REWINDS WHEN PLUGGED IN	CHECK RESET CIRCUIT
GOLDSTAR	GHV1910	N/A	MANY VERTICAL BARS ON THE SCREEN THAT FLASH ON AND OFF IF THE CLOCK HASN'T BEEN SET.	CHECK/REPLACE IC801
GOLDSTAR	GHV4500	N/A	PART CHANGE FOR RELIABILITY	CHANGE C119 FROM A 22uF/16V TO A 22uF/50V
GOLDSTAR	GHV4500M	N/A	WOW AND FLUTTER GREATER THAN NORMAL	CHECK/REPLACE CAPSTAN MOTOR,IC501 ALSO DELETE D297 AND D298
GOLDSTAR	GHV4500M	N/A	TUNER AUDIO DISTORTED	CHANGE R708 TO 390 ohm - R709 TO 820 ohm AND C709 TO 27pf
GOLDSTAR	GHV4500M	N/A	OSD GRAPHICS SLANT	CHANGE C801 TO 33pF - L802 TO 15uH COIL (P/N 0LR0152K530) AND DELETE C802
GOLDSTAR	GHV4500M	N/A	ERRATIC TAPE COUNTER OPERATION	CHANGE R516 TO A 27k
GOLDSTAR	GHV4700M	N/A	AUDIO DISTORTION	CHANGE R708 TO 390 ohm - R709 TO 820 ohm - C709 TO 27pf
GOLDSTAR	GHV4700M	N/A	WON'T RECORD AUDIO OR ERASE OLD AUDIO	CHECK/REPLACE R427 FOR OPEN (47k)
GOLDSTAR	GHV4700M	N/A	OSD TITLES ARE TOO DIM	CHANGE R864 TO A 8.2k
GOLDSTAR	GHV4700M	N/A	PICTURE DISTORTION DURING TITLE MODE (THE AUDIO OSC. INTERFERES W/THE VIDEO SIGNAL DURING REC)	REMOVE C871 FROM CIRCUIT
GOLDSTAR	GHV51FM	N/A	1 KHz TONE IN AUDIO ON PLAYBACK	CHECK/REPLACE R401 OR OPEN GROUND TO THE GROUND SIDE OF HEAD
GOLDSTAR	GHV51FM	N/A	WILL NOT ACCEPT TAPE	CHECK IC602
GOLDSTAR	GHV51FM	N/A	NO SPEED CONTROL - RUNAWAY ON PLAY	CHECK/REPLACE C247 AND C248
GOLDSTAR	GHV5220M	N/A	EXCESSIVE WOW AND FLUTTER	CHANGE R234 TO A 180k AND R238 TO A 27k
GOLDSTAR	GHV5220M	N/A	WILL NOT RECORD A CONTROL TRACK ON TAPE - PRE-RECORDED TAPES WOULD PLAYBACK FINE ON ALL SPEEDS	CHECK/REPLACE IC201 (P/N# 668-156A)
GOLDSTAR	GHV5300M	N/A	NO TUNER VIDEO - ONLY A BLUE SCREEN	CHANGE RS05 TO A 10k
GOLDSTAR	GHV5300M	N/A	EXCESSIVE WOW AND FLUTTER	CHANGE R234 TO A 180k AND R238 TO A 27k
GOLDSTAR	GHV55FM	N/A	1 KHz TONE IN AUDIO ON PLAYBACK	CHECK/REPLACE R401 OR OPEN GROUND TO THE GROUND SIDE OF HEAD
GOLDSTAR	GHV55FM	N/A	NO SPEED CONTROL - RUNAWAY ON PLAY	CHECK/REPLACE C247 AND C248
GOLDSTAR	GHV55FM	N/A	WILL NOT ACCEPT TAPE	CHECK IC602
GOLDSTAR	GHV57FM	N/A	CLOCK RUNS TOO FAST	REMOVE D807 AND CHANGE C907 TO A 22uF @ 50V AND IF PROBLEM STILL PERSISTS,CHANGE C907 TO A 47uF @ 50V
GOLDSTAR	GHV8200M	N/A	NO DRUM OR CAPSTAN ROTATION	CHECK/REPLACE R215 FOR OPEN - ALSO Vcc & Vdd TO IC201
GOLDSTAR	GHV8500	N/A	WHEN USING THE CHANNEL UP/DOWN BUTTONS,SOMETIMES THE PIX IS DISTORTED OR SET SKIPS CHANNELS	DELETE R706
GOLDSTAR	GHV8500M	N/A	HI-FI AUDIO DROPS OUT INTERMITTENTLY	REMOVE R414

LAMSON Digital Electronics Address: 1324-1326 Jose Abad Santos Ave.,Manila, Philippines TEL:00632-2559675  TEL/FAX:00632-2568130 Cellular:0922-8867809 0922-8867810 E-mail:[email protected]    YAHOO MESSENGER ID : myrna_q_ng or saishu_ng SKYPE ID: myrna_q_ng or saishu_ng (old) Lamson Importers & Exporters Trading <We will not be using the old address and phone no. in the future. Please be noted when calling us, sending letters, parcels or buying our products> OLD Address: 681 Carmen Building, Ronquillo St. Quiapo, Manila, Philippines Phone:00632-7332936 7332940 Fax:00632-7332940 E-mail: