MAKE | MODEL | CHASSIS | SYMPTOM | CURE | |
GOLDSTAR | GHV8500M | N/A | TAPE COUNTER OPERATION ERRATIC | CHANGE R515 TO A 27k | |
GOLDSTAR | GHV8500M | N/A | CHANNEL 19 ON CATV IS SOMETIMES SKIPPED WHEN THE TEMP. OF THE UNIT IS HIGH | DELETE C805 | |
GOLDSTAR | GHV8500M | N/A | WOW AND FLUTTER BAD IN THE EP MODE | CHANGE R221 TO A 180k AND R223 TO A 27k | |
GOLDSTAR | GHV8500M | N/A | HI-FI MODE IS INTERMITTENT | CHANGE R653 TO A 270 ohm | |
GOLDSTAR | GHV8500M | N/A | COLOR INTERFERENCE WHEN USING THE VIDEO INPUT JACK | REMOVE JUMPER J302 | |
GOLDSTAR | GHV8500M | N/A | TUNER IF DISTORTION IN THE EE MODE | CHANGE R732 TO 820 ohm AND R708 TO 270 ohm | |
GOLDSTAR | GHV8500M | N/A | POOR TRACKING RANGE | CHANGE R204 TO A 270k | |
GOLDSTAR | GHV9000 | N/A | WHEN USING THE CHANNEL UP/DOWN BUTTONS,SOMETIMES THE PIX IS DISTORTED OR SET SKIPS CHANNELS | DELETE R706 | |
GOLDSTAR | GHV9000 | N/A | NO PICTURE IN THE TUNER MODE | CHANGE C819 TO 510pF | |
GOLDSTAR | GHV9000M | N/A | UNABLE TO GET CATV CHANNEL 6 | CHANGE R743 TO 120k AND R825 TO 820k | |
GOLDSTAR | GHV9000M | N/A | DYNAMIC RANGE OF AUDIO IS TOO LOW - POOR RESPONSE | DELETE C403 AND C421 | |
GOLDSTAR | GHV9000M | N/A | CHANNEL 19 ON CATV IS SOMETIMES SKIPPED WHEN THE TEMP. OF THE UNIT IS HIGH | DELETE C805 | |
GOLDSTAR | GHV9000M | N/A | TUNER IF DISTORTION IN THE EE MODE | CHANGE R732 TO 820 ohm AND R708 TO 270 ohm | |
GOLDSTAR | GHV9000M | N/A | COLOR NOISE | DELETE JUMPER J302 | |
GOLDSTAR | GHV9000M | N/A | HI-FI AUDIO DROPS OUT INTERMITTENTLY | REMOVE R414 | |
GOLDSTAR | GHV9000M | N/A | HI-FI MODE IS INTERMITTENT | CHANGE R653 TO A 270 ohm | |
GOLDSTAR | GHV9000M | N/A | LOSES FUNCTION AND DISPLAY | CHECK/REPLACE IC901 OR RESET CIRCUIT | |
GOLDSTAR | GHV9000M | N/A | AUDIO HUM IS TOO GREAT | CHANGE C444 TO .0015uF - C434 TO 220uF @ 6.3v -C435 TO 220uF @ 6.3v | |
GOLDSTAR | GHV9000M | N/A | TAPE COUNTER OPERATION ERRATIC | CHANGE R515 TO A 27k | |
GOLDSTAR | GVCA425 | N/A | DISTORTION OF THE CTRL. PULSE AT PIN 6 OF IC501 - PIX NOT DISPLAYED IN THE REC/REV MODE | ADD R5C1 TO THE CATHODE OF D213 TO GROUND | |
GOLDSTAR | GVCD435 | N/A | POOR VISS DETECTION | CHANGE R222 TO A 680 (P/N# ORD6800F608) | |
GOLDSTAR | GVCD455 | N/A | POOR VISS DETECTION | CHANGE R222 TO A 680 (P/N# ORD6800F608) | |
GOLDSTAR | GVDD150 | N/A | POWER SUPPLY IS NOT STABLE | CHANGE RP07 TO A 1.5k | |
GOLDSTAR | GVDD150 | N/A | SWITCHING REGULATOR SHORTS - POSSIBLY DUE TO A SURGE | CHECK/REPLACE QP01 - CHANGE RP06 TO 1.2 @ 2watt (P/N# 0RW0121K600) AND RP09 TO 330 (P/N# 0RD3300F608) | |
GOLDSTAR | GVPB115 | N/A | WHEN TAPE IS INSERTED, IT IS EJECTED AUTOMATICALLY | CHANGE R506/R507 TO 7.5k (0RD7501F608) | |
GOLDSTAR | GVPB115 | N/A | HIGH LEVEL OF AUDIO DISTORTION AT HIGH TEMPERATURE | ADD 10k TO BASE OF Q408 AND Q409 TO GROUND | |
GOLDSTAR | GVPB115 | N/A | INTERMITTENT ERROR OR ALARM WHEN GOING FROM ONE MODE TO ANOTHER | CHECK/REPLACE MODE SELECT SWITCH | |
GOLDSTAR | GVPB115 | N/A | POOR WOW AND FLUTTER | CHANGE R208 TO 120k, R212 TO 1meg AND REMOVE R259 | |
GOLDSTAR | GVPB115 | N/A | MACHINE SHOWS 'ERROR' WHEN IN THE EJECT MODE | CHECK/REPLACE GEAR 'C' (P/N# 435-256B) OR DRIVE ASSY. (P/N# 435-257B) OR HOUSING ASSY. (P/N# 219-017E) | |
GOLDSTAR | GVPB115 | N/A | COLOR IS SLOW TO POP IN WHILE IN PLAY MODE | CHANGE R326 TO 4.7K | |
GOLDSTAR | GVPB115 | N/A | POOR WOW AND FLUTTER | CHANGE R208 TO 120k , R212 TO 1m AND REMOVE R259 | |
GOLDSTAR | GVPB115 | N/A | REMOTE RECEPTON IS ERRATIC | CHANGE C554 TO 680pF @ 50v (P/N# 0CN6810K518) | |
GOLDSTAR | GVPB125 | N/A | POOR WOW AND FLUTTER | CHANGE R208 TO 120k, R212 TO 1meg AND REMOVE R259 | |
GOLDSTAR | GVPB125 | N/A | REMOTE RECEPTON IS ERRATIC | CHANGE C554 TO 680pF @ 50v (P/N# 0CN6810K518) | |
GOLDSTAR | GVPB125 | N/A | HIGH LEVEL OF AUDIO DISTORTION AT HIGH TEMPERATURE | ADD 10k TO BASE OF Q408 AND Q409 TO GROUND | |
GOLDSTAR | GVPB125 | N/A | MACHINE SHOWS 'ERROR' WHEN IN THE EJECT MODE | CHECK/REPLACE GEAR 'C' (P/N# 435-256B) OR DRIVE ASSY. (P/N# 435-257B) OR HOUSING ASSY. (P/N# 219-017E) | |
GOLDSTAR | GVPB125 | N/A | INTERMITTENT ERROR OR ALARM WHEN GOING FROM ONE MODE TO ANOTHER | CHECK/REPLACE MODE SELECT SWITCH | |
GOLDSTAR | GVPB125 | N/A | COLOR IS SLOW TO POP IN WHILE IN PLAY MODE | CHANGE R326 TO 4.7K | |
GOLDSTAR | GVPB125 | N/A | POOR WOW AND FLUTTER | CHANGE R208 TO 120k , R212 TO 1m AND REMOVE R259 | |
GOLDSTAR | GVPB125 | N/A | WHEN TAPE IS INSERTED, IT IS EJECTED AUTOMATICALLY | CHANGE R506/R507 TO 7.5k (0RD7501F608) | |
GOLDSTAR | GVPB135 | N/A | REMOTE RECEPTON IS ERRATIC | CHANGE C554 TO 680pF @ 50v (P/N# 0CN6810K518) | |
GOLDSTAR | GVPB135 | N/A | POOR WOW AND FLUTTER | CHANGE R208 TO 120k , R212 TO 1m AND REMOVE R259 | |
GOLDSTAR | GVPB135 | N/A | WHEN TAPE IS INSERTED, IT IS EJECTED AUTOMATICALLY | CHANGE R506/R507 TO 7.5k (0RD7501F608) | |
GOLDSTAR | GVPB135 | N/A | MACHINE SHOWS 'ERROR' WHEN IN THE EJECT MODE | CHECK/REPLACE GEAR 'C' (P/N# 435-256B) OR DRIVE ASSY. (P/N# 435-257B) OR HOUSING ASSY. (P/N# 219-017E) | |
GOLDSTAR | GVPB135 | N/A | COLOR IS SLOW TO POP IN WHILE IN PLAY MODE | CHANGE R326 TO 4.7K | |
GOLDSTAR | GVPB135 | N/A | HIGH LEVEL OF AUDIO DISTORTION AT HIGH TEMPERATURE | ADD 10k TO BASE OF Q408 AND Q409 TO GROUND | |
GOLDSTAR | GVPB135 | N/A | POOR WOW AND FLUTTER | CHANGE R208 TO 120k, R212 TO 1meg AND REMOVE R259 | |
GOLDSTAR | GVPB135 | N/A | INTERMITTENT ERROR OR ALARM WHEN GOING FROM ONE MODE TO ANOTHER | CHECK/REPLACE MODE SELECT SWITCH | |
GOLDSTAR | GVPC120 | N/A | NO AUDIO ON PLAYBACK | CHECK/REPLACE Q104 (P/N# OTR319809AC OR ECG85) | |
GOLDSTAR | GVPC120 | N/A | NO AUDIO ON PLAYBACK | CHECK/REPLACE Q104 (USE P/N# ECG85) | |
GOLDSTAR | GVPC120 | N/A | IMPROVEMENT OF AUTO-TRACKING | CHANGE C620 TO A 1uF @ 50V (P/N# CE,1MF-M50V) | |
GOLDSTAR | GVPC120 | N/A | UNSTABLE PICTURE IN CUE AND REVIEW | REMOVE R241,R244 AND R243 | |
GOLDSTAR | GVPC125 | N/A | UNSTABLE PICTURE IN CUE AND REVIEW | REMOVE R241,R244 AND R243 | |
GOLDSTAR | GVPC125 | N/A | NO AUDIO ON PLAYBACK | CHECK/REPLACE Q104 (USE P/N# ECG85) | |
GOLDSTAR | GVPC125 | N/A | IMPROVEMENT OF AUTO-TRACKING | CHANGE C620 TO A 1uF @ 50V (P/N# CE,1MF-M50V) | |
GOLDSTAR | GVPC125 | N/A | NO AUDIO ON PLAYBACK | CHECK/REPLACE Q104 (P/N# OTR319809AC OR ECG85) | |
GOLDSTAR | GVPC135 | N/A | IMPROVEMENT OF AUTO-TRACKING | CHANGE C620 TO A 1uF @ 50V (P/N# CE,1MF-M50V) | |
GOLDSTAR | GVPC135 | N/A | UNSTABLE PICTURE IN CUE AND REVIEW | REMOVE R241,R244 AND R243 | |
GOLDSTAR | GVPC200 | N/A | POP NOISE HEARD IN AUDIO | CHECK/REPLACE IC401 (P/N# 0IMA3970NFBP),CHANGE R4A1 TO 33k (P/N# 0RD3302F608) AND C4A1 TO 10uF@16v (P/N# 0CE1064F638) | |
GOLDSTAR | GVPC200 | N/A | WHEN TAPE IS INSERTED, IT IS EJECTED AUTOMATICALLY | CHANGE R506/R507 TO 7.5k (0RD7501F608) | |
GOLDSTAR | GVPC200 | N/A | REMOTE RECEPTON IS ERRATIC | CHANGE C554 TO 680pF @ 50v (P/N# 0CN6810K518) | |
GOLDSTAR | GVPD150 | N/A | POOR AUTO-TRACKING - SLOW CTL DETECTION | CHANGE R249 TO 1.2k (0RD1201F608) AND ADD 0.01uF @ 16v FROM PIN 3 OF IC202 TO GROUND. (C275) (P/N# 0CN1030F678) | |
GOLDSTAR | GVPE130 | N/A | POOR AUTO-TRACKING - SLOW CTL DETECTION | CHANGE R249 TO 1.2k (0RD1201F608) AND ADD 0.01uF @ 16v FROM PIN 3 OF IC202 TO GROUND. (C275) (P/N# 0CN1030F678) | |
GOLDSTAR | GVPF130 | N/A | CAPSTAN MOTOR RUNS VERY FAST OR MAY STOP AND NOT RUN AT ALL | CHECK/RESOLDER CONNECTIONS ON IC205 | |
GOLDSTAR | GVRA215 | N/A | MACHINE SHOWS 'ERROR' WHEN IN THE EJECT MODE | CHECK/REPLACE GEAR 'C' (P/N# 435-256B) OR DRIVE ASSY. (P/N# 435-257B) OR HOUSING ASSY. (P/N# 219-017E) | |
GOLDSTAR | GVRA215 | N/A | WHEN POWER BUTTON IS PUSHED, THE PICTURE IS DELAYED | CHANGE C709 TO 22uF@16v | |
GOLDSTAR | GVRA215 | N/A | AUDIO DISTORTION | CHANGE R013 TO 1k | |
GOLDSTAR | GVRA215 | N/A | EXCESSIVE NOISE ON OLDER TAPES | LIFT R251 END THAT JOINS W/R214 & R215;ADD A 1SS131 W/ANODE TO R214,CATHODE TO LOOSE END OF R251,CHANGE R215 TO 1k | |
GOLDSTAR | GVRA215 | N/A | INTERMITTENT AUTO STOP | CHANGE C229 TO 0.22uF @ 100v | |
GOLDSTAR | GVRA215 | N/A | MODIFICATION TO KEEP CASSETTE HOUSING FROM MOVING | ADD 321-516A,353-051A,353-046B (BRACKETS AND SCREWS) | |
GOLDSTAR | GVRA215 | N/A | FAILURE OF PICTURE TO APPEAR AFTER A POWER FAILURE | CHANGE C223 TO A 10uF @ 25v | |
GOLDSTAR | GVRA215 | N/A | ZD501 HAS A TENDENCY TO OVER HEAT | CHANGE ZD501 TO A 1.5k RESISTOR AND R525 TO A 4.7k | |
GOLDSTAR | GVRA215 | N/A | DIGITAL IS DIM OR TOO DARK | CHANGE R111 AND R112 TO 3.3 ohm | |
GOLDSTAR | GVRA225 | N/A | REWIND AND FAST FORWARD NOT WORKING | CHECK/REPLACE F/R BRACKET WITH NEW TYPE (P/N# 321-397D) | |
GOLDSTAR | GVRA225 | N/A | WHEN POWER BUTTON IS PUSHED, THE PICTURE IS DELAYED | CHANGE C709 TO 22uF@16v | |
GOLDSTAR | GVRA225 | N/A | ZD501 HAS A TENDENCY TO OVER HEAT | CHANGE ZD501 TO A 1.5k RESISTOR AND R525 TO A 4.7k | |
GOLDSTAR | GVRA225 | N/A | INTERMITTENT ERROR OR ALARM WHEN GOING FROM ONE MODE TO ANOTHER | CHECK/REPLACE MODE SELECT SWITCH | |
GOLDSTAR | GVRA225 | N/A | MODIFICATION TO KEEP CASSETTE HOUSING FROM MOVING | ADD 321-516A,353-051A,353-046B (BRACKETS AND SCREWS) | |
GOLDSTAR | GVRA225 | N/A | AUDIO DISTORTION | CHANGE R013 TO 1k | |
GOLDSTAR | GVRA225 | N/A | FAILURE OF PICTURE TO APPEAR AFTER A POWER FAILURE | CHANGE C223 TO A 10uF @ 25v | |
GOLDSTAR | GVRA225 | N/A | INTERMITTENT AUTO STOP | CHANGE C229 TO 0.22uF @ 100v | |
GOLDSTAR | GVRA225 | N/A | EXCESSIVE NOISE ON OLDER TAPES | LIFT R251 END THAT JOINS W/R214 & R215;ADD A 1SS131 W/ANODE TO R214,CATHODE TO LOOSE END OF R251,CHANGE R215 TO 1k | |
GOLDSTAR | GVRA225 | N/A | DIGITAL IS DIM OR TOO DARK | CHANGE R111 AND R112 TO 3.3 ohm | |
GOLDSTAR | GVRA225 | N/A | MACHINE SHOWS 'ERROR' WHEN IN THE EJECT MODE | CHECK/REPLACE GEAR 'C' (P/N# 435-256B) OR DRIVE ASSY. (P/N# 435-257B) OR HOUSING ASSY. (P/N# 219-017E) | |
GOLDSTAR | GVRA234 | N/A | AUDIO DISTORTION | CHANGE R013 TO 1k | |
GOLDSTAR | GVRA235 | N/A | ZD501 HAS A TENDENCY TO OVER HEAT | CHANGE ZD501 TO A 1.5k RESISTOR AND R525 TO A 4.7k | |
GOLDSTAR | GVRA235 | N/A | MODIFICATION TO KEEP CASSETTE HOUSING FROM MOVING | ADD 321-516A,353-051A,353-046B (BRACKETS AND SCREWS) | |
GOLDSTAR | GVRA235 | N/A | REWIND AND FAST FORWARD NOT WORKING | CHECK/REPLACE F/R BRACKET WITH NEW TYPE (P/N# 321-397D) | |
GOLDSTAR | GVRA235 | N/A | MACHINE SHOWS 'ERROR' WHEN IN THE EJECT MODE | CHECK/REPLACE GEAR 'C' (P/N# 435-256B) OR DRIVE ASSY. (P/N# 435-257B) OR HOUSING ASSY. (P/N# 219-017E) | |
GOLDSTAR | GVRA235 | N/A | EXCESSIVE NOISE ON OLDER TAPES | LIFT R251 END THAT JOINS W/R214 & R215;ADD A 1SS131 W/ANODE TO R214,CATHODE TO LOOSE END OF R251,CHANGE R215 TO 1k | |
GOLDSTAR | GVRA235 | N/A | FAILURE OF PICTURE TO APPEAR AFTER A POWER FAILURE | CHANGE C223 TO A 10uF @ 25v | |
GOLDSTAR | GVRA235 | N/A | INTERMITTENT ERROR OR ALARM WHEN GOING FROM ONE MODE TO ANOTHER | CHECK/REPLACE MODE SELECT SWITCH | |
GOLDSTAR | GVRA235 | N/A | WHEN POWER BUTTON IS PUSHED, THE PICTURE IS DELAYED | CHANGE C709 TO 22uF@16v | |
GOLDSTAR | GVRA235 | N/A | DIGITAL IS DIM OR TOO DARK | CHANGE R111 AND R112 TO 3.3 ohm | |
GOLDSTAR | GVRA235 | N/A | INTERMITTENT AUTO STOP | CHANGE C229 TO 0.22uF @ 100v | |
GOLDSTAR | GVRA245 | N/A | INTERMITTENT ERROR OR ALARM WHEN GOING FROM ONE MODE TO ANOTHER | CHECK/REPLACE MODE SELECT SWITCH | |
GOLDSTAR | GVRA245 | N/A | MODIFICATION TO KEEP CASSETTE HOUSING FROM MOVING | ADD 321-516A,353-051A,353-046B (BRACKETS AND SCREWS) | |
GOLDSTAR | GVRA245 | N/A | INTERMITTENT AUTO STOP | CHANGE C229 TO 0.22uF @ 100v | |
GOLDSTAR | GVRA245 | N/A | FAILURE OF PICTURE TO APPEAR AFTER A POWER FAILURE | CHANGE C223 TO A 10uF @ 25v | |
GOLDSTAR | GVRA245 | N/A | DIGITAL IS DIM OR TOO DARK | CHANGE R111 AND R112 TO 3.3 ohm | |
GOLDSTAR | GVRA245 | N/A | WHEN POWER BUTTON IS PUSHED, THE PICTURE IS DELAYED | CHANGE C709 TO 22uF@16v | |
GOLDSTAR | GVRA245 | N/A | EXCESSIVE NOISE ON OLDER TAPES | LIFT R251 END THAT JOINS W/R214 & R215;ADD A 1SS131 W/ANODE TO R214,CATHODE TO LOOSE END OF R251,CHANGE R215 TO 1k | |
GOLDSTAR | GVRA245 | N/A | MACHINE SHOWS 'ERROR' WHEN IN THE EJECT MODE | CHECK/REPLACE GEAR 'C' (P/N# 435-256B) OR DRIVE ASSY. (P/N# 435-257B) OR HOUSING ASSY. (P/N# 219-017E) | |
GOLDSTAR | GVRA245 | N/A | AUDIO DISTORTION | CHANGE R013 TO 1k | |
GOLDSTAR | GVRA245 | N/A | PICTURE IS MOMENTARILY DISTORTED WHEN THE CHANNEL UP OR DOWN BUTTON IS PUSHED | CHANGE C704 TO A 2.2uF IN 'IF' PACK | |
GOLDSTAR | GVRA245 | N/A | REWIND AND FAST FORWARD NOT WORKING | CHECK/REPLACE F/R BRACKET WITH NEW TYPE (P/N# 321-397D) | |
GOLDSTAR | GVRA245 | N/A | ZD501 HAS A TENDENCY TO OVER HEAT | CHANGE ZD501 TO A 1.5k RESISTOR AND R525 TO A 4.7k | |
GOLDSTAR | GVRA435 | N/A | SLIGHT AUDIO HUM | CHANGE C427 TO 4.7uF@50v PC TYPE, C428 TO 0.001uF AXIAL TYPE AND C429 TO 470pF AXIAL TYPE | |
GOLDSTAR | GVRA435 | N/A | IN THE EP SPEED,THE OSD IS BENT | CHANGE R073 TO 10k AND R074 TO A 8.2k | |
GOLDSTAR | GVRA435 | N/A | REWIND AND FAST FORWARD NOT WORKING | CHECK/REPLACE F/R BRACKET WITH NEW TYPE (P/N# 321-397D) | |
GOLDSTAR | GVRA435 | N/A | AUDIO DISTORTION WHILE IN TUNER MODE | CHANGE L708 TO 22uH (P/N# OLR0222K035) | |
GOLDSTAR | GVRA435 | N/A | INTERMITTENT ERROR OR ALARM WHEN GOING FROM ONE MODE TO ANOTHER | CHECK/REPLACE MODE SELECT SWITCH | |
GOLDSTAR | GVRA435 | N/A | MACHINE SHOWS 'ERROR' WHEN IN THE EJECT MODE | CHECK/REPLACE GEAR 'C' (P/N# 435-256B) OR DRIVE ASSY. (P/N# 435-257B) OR HOUSING ASSY. (P/N# 219-017E) | |
GOLDSTAR | GVRA445 | N/A | REWIND AND FAST FORWARD NOT WORKING | CHECK/REPLACE F/R BRACKET WITH NEW TYPE (P/N# 321-397D) | |
GOLDSTAR | GVRA445 | N/A | INTERMITTENT ERROR OR ALARM WHEN GOING FROM ONE MODE TO ANOTHER | CHECK/REPLACE MODE SELECT SWITCH | |
GOLDSTAR | GVRA445 | N/A | SLIGHT AUDIO HUM | CHANGE C427 TO 4.7uF@50v PC TYPE, C428 TO 0.001uF AXIAL TYPE AND C429 TO 470pF AXIAL TYPE | |
GOLDSTAR | GVRA445 | N/A | AUDIO DISTORTION WHILE IN TUNER MODE | CHANGE L708 TO 22uH (P/N# OLR0222K035) | |
GOLDSTAR | GVRA445 | N/A | MACHINE SHOWS 'ERROR' WHEN IN THE EJECT MODE | CHECK/REPLACE GEAR 'C' (P/N# 435-256B) OR DRIVE ASSY. (P/N# 435-257B) OR HOUSING ASSY. (P/N# 219-017E) | |
GOLDSTAR | GVRA445 | N/A | IN THE EP SPEED,THE OSD IS BENT | CHANGE R073 TO 10k AND R074 TO A 8.2k | |
GOLDSTAR | GVRA445 | N/A | INTERMITTENT COLOR | CHECK/REPLACE L601 | |
GOLDSTAR | GVRA465 | N/A | NOISE IN AUDIO (HUM) DUE TO LOW AC VOLTAGE | CHANGE C103 TO A 2200uF @ 25v | |
GOLDSTAR | GVRA465 | N/A | SLIGHT AUDIO HUM | CHANGE C427 TO 4.7uF@50v PC TYPE, C428 TO 0.001uF AXIAL TYPE AND C429 TO 470pF AXIAL TYPE | |
GOLDSTAR | GVRA465 | N/A | MACHINE SHOWS 'ERROR' WHEN IN THE EJECT MODE | CHECK/REPLACE GEAR 'C' (P/N# 435-256B) OR DRIVE ASSY. (P/N# 435-257B) OR HOUSING ASSY. (P/N# 219-017E) | |
GOLDSTAR | GVRA465 | N/A | AUDIO DISTORTION WHILE IN TUNER MODE | CHANGE L708 TO 22uH (P/N# OLR0222K035) | |
GOLDSTAR | GVRA465 | N/A | NOISY PICTURE IN THE EP MODE | CHANGE R638 TO A 3.9k | |
GOLDSTAR | GVRA465 | N/A | OCCASSIONAL WHITE SPOTS IN EP MODE | REMOVE C605 AND C606 | |
GOLDSTAR | GVRA465 | N/A | INTERMITTENT ERROR OR ALARM WHEN GOING FROM ONE MODE TO ANOTHER | CHECK/REPLACE MODE SELECT SWITCH | |
GOLDSTAR | GVRA465 | N/A | HI-FI LED FLICKER | CHANGE R038 TO 47k, R801 TO 3.3k, AND C845 TO 2.2uF@50v | |
GOLDSTAR | GVRA465 | N/A | REWIND AND FAST FORWARD NOT WORKING | CHECK/REPLACE F/R BRACKET WITH NEW TYPE (P/N# 321-397D) | |
GOLDSTAR | GVRA485 | N/A | REWIND AND FAST FORWARD NOT WORKING | CHECK/REPLACE F/R BRACKET WITH NEW TYPE (P/N# 321-397D) | |
GOLDSTAR | GVRA485 | N/A | WHEN PLAYING OLD TAPES THE VIDEO IS MUTED INTERMITTENTLY DUE TO LOW FM ENVELOPE OUTPUT. | CHANGE R330 TO A 100k | |
GOLDSTAR | GVRA485 | N/A | LOSS OF PICTURE IN THE E-E MODE | ADD C747 (1000pF @ 50v) TO IC901 PIN 2 TO GROUND | |
GOLDSTAR | GVRA485 | N/A | DISTORTED HORZ SYNC AT VIDEO OUTPUT | CHANGE R713 TO A 1.2k | |
GOLDSTAR | GVRA485 | N/A | PICTURE IS DISTORTED IN THE CUE MODE | ADD A 0.01uF TO THE + SIDE OF C241 TO GROUND | |
GOLDSTAR | GVRA485 | N/A | MACHINE SHOWS 'ERROR' WHEN IN THE EJECT MODE | CHECK/REPLACE GEAR 'C' (P/N# 435-256B) OR DRIVE ASSY. (P/N# 435-257B) OR HOUSING ASSY. (P/N# 219-017E) | |
GOLDSTAR | GVRA485 | N/A | DURING LOSS OF AC POWER IN THE PLAY MODE,THE TAPE MAY BE ERASED DUE TO AN UNSTABLE ERASE CIRCUIT | CHANGE C914 TO A 2.2uF @ 50v | |
GOLDSTAR | GVRA485 | N/A | INTERMITTENT ERROR OR ALARM WHEN GOING FROM ONE MODE TO ANOTHER | CHECK/REPLACE MODE SELECT SWITCH | |
GOLDSTAR | GVRA485 | N/A | OSD JITTERS | ADD A 47k FROM PIN 9 OF IC002 TO GROUND | |
GOLDSTAR | GVRA485 | N/A | OSD JUMPS WHEN VCR IS VIBRATED | REMOVE VR001, ADD R002 8.2k ACROSS PINS 5 & 6 OF IC003, ADD R080 5.6k FROM IC003 PIN5 TO R003 (FREE END),R003 >5.6k | |
GOLDSTAR | GVRA485 | N/A | PICTURE JUMPS VERTICALLY ON PLAYBACK | READJUST PG SHIFTERS TO SPECS. | |
GOLDSTAR | GVRB235 | N/A | MACHINE SHOWS 'ERROR' WHEN IN THE EJECT MODE | CHECK/REPLACE GEAR 'C' (P/N# 435-256B) OR DRIVE ASSY. (P/N# 435-257B) OR HOUSING ASSY. (P/N# 219-017E) | |
GOLDSTAR | GVRB235 | N/A | AUDIO DISTORTION | CHANGE R013 TO 1k | |
GOLDSTAR | GVRB245 | N/A | INTERMITTENT ERROR OR ALARM WHEN GOING FROM ONE MODE TO ANOTHER | CHECK/REPLACE MODE SELECT SWITCH | |
GOLDSTAR | GVRB245 | N/A | MACHINE SHOWS 'ERROR' WHEN IN THE EJECT MODE | CHECK/REPLACE GEAR 'C' (P/N# 435-256B) OR DRIVE ASSY. (P/N# 435-257B) OR HOUSING ASSY. (P/N# 219-017E) | |
GOLDSTAR | GVRB245 | N/A | REWIND AND FAST FORWARD NOT WORKING | CHECK/REPLACE F/R BRACKET WITH NEW TYPE (P/N# 321-397D) | |
GOLDSTAR | GVRB245 | N/A | AUDIO DISTORTION | CHANGE R013 TO 1k | |
GOLDSTAR | GVRB435 | N/A | SKIPS MEMORIZED CHANNELS WHEN VCR IS IN A LOW TEMPERATURE SETTING | CHANGE R016 TO A 8.2k | |
GOLDSTAR | GVRB435 | N/A | AUDIO DISTORTION | CHANGE R013 TO 1k | |
GOLDSTAR | GVRB435 | N/A | MACHINE SHOWS 'ERROR' WHEN IN THE EJECT MODE | CHECK/REPLACE GEAR 'C' (P/N# 435-256B) OR DRIVE ASSY. (P/N# 435-257B) OR HOUSING ASSY. (P/N# 219-017E) | |
GOLDSTAR | GVRB435 | N/A | INTERMITTENTLY POWER WON'T TURN ON OR OFF WILL REMOTE | ADD C2A1 CAPACITOR (P/N# 0CC6810K405) 680pF | |
GOLDSTAR | GVRB435 | N/A | VCR GOES DEAD WHEN TRYING TO INSERT A TAPE - NO DISPLAY | CHECK/REPLACE Q104 (P/N# 2SA1273Y - OTR127300AA) | |
GOLDSTAR | GVRB435 | N/A | WEAK AUDIO CAUSING TUNER AUDIO TO BE WEAK THEREFORE RECORDINGS WERE A LITTLE LOW | CHANGE R421 TO 47k | |
GOLDSTAR | GVRB435 | N/A | AUDIO BUZZ INTERMITTENT IN THE SLOW OR STILL MODE | ADD R2B1 56k FROM IC201 PIN 48 TO GROUND | |
GOLDSTAR | GVRB435 | N/A | IF POWER GOES OFF FOR ONE SECOND THEN BACK ON, VCR MAY NOT COME BACK ON DUE TO RESET OF PROCESSOR TIME TOO SHORT | CHANGE R248 TO 47k AND C234 TO 10uF @ 50v | |
GOLDSTAR | GVRB435 | N/A | AUDIO HUM | CHANGE R3D5 TO 680 (P/N# 0RD6800F608) | |
GOLDSTAR | GVRB445 | N/A | AUDIO HUM | CHANGE R3D5 TO 680 (P/N# 0RD6800F608) | |
GOLDSTAR | GVRB445 | N/A | WEAK AUDIO CAUSING TUNER AUDIO TO BE WEAK THEREFORE RECORDINGS WERE A LITTLE LOW | CHANGE R421 TO 47k | |
GOLDSTAR | GVRB445 | N/A | REWIND AND FAST FORWARD NOT WORKING | CHECK/REPLACE F/R BRACKET WITH NEW TYPE (P/N# 321-397D) | |
GOLDSTAR | GVRB445 | N/A | IF POWER GOES OFF FOR ONE SECOND THEN BACK ON, VCR MAY NOT COME BACK ON DUE TO RESET OF PROCESSOR TIME TOO SHORT | CHANGE R248 TO 47k AND C234 TO 10uF @ 50v | |
GOLDSTAR | GVRB445 | N/A | SKIPS MEMORIZED CHANNELS WHEN VCR IS IN A LOW TEMPERATURE SETTING | CHANGE R016 TO A 8.2k | |
GOLDSTAR | GVRB445 | N/A | BLUE SCREEN DOESN'T ALWAYS APPEAR ON UHF | CHECK/REPLACE C519 (0.01uF @ 100v) | |
GOLDSTAR | GVRB445 | N/A | AUDIO DISTORTION | CHANGE R013 TO 1k | |
GOLDSTAR | GVRB445 | N/A | TUNER SHORTED | REMOVE JUMPER W105 AND REPLACE WITH A 1k RESISTOR (P/N# 0RD1001F608) | |
GOLDSTAR | GVRB445 | N/A | INTERMITTENTLY POWER WON'T TURN ON OR OFF WILL REMOTE | ADD C2A1 CAPACITOR (P/N# 0CC6810K405) 680pF | |
GOLDSTAR | GVRB445 | N/A | MACHINE SHOWS 'ERROR' WHEN IN THE EJECT MODE | CHECK/REPLACE GEAR 'C' (P/N# 435-256B) OR DRIVE ASSY. (P/N# 435-257B) OR HOUSING ASSY. (P/N# 219-017E) | |
GOLDSTAR | GVRB445 | N/A | DIM DISPLAY | CHANGE R263,R264,R265 AND R266 TO 3.3ohms | |
GOLDSTAR | GVRB445 | N/A | INTERMITTENT ERROR OR ALARM WHEN GOING FROM ONE MODE TO ANOTHER | CHECK/REPLACE MODE SELECT SWITCH | |
GOLDSTAR | GVRB455 | N/A | INTERMITTENTLY POWER WON'T TURN ON OR OFF WILL REMOTE | ADD C2A1 CAPACITOR (P/N# 0CC6810K405) 680pF | |
GOLDSTAR | GVRB455 | N/A | STEREO SOUND LOSES IT'S CLARITY AFTER ON IN THE E-E MODE FOR SEVERAL HOURS | CHANGE R706 TO A 1k AND REMOVE C710 AND REPLACE WITH A SHORT OR PIECE OF WIRE | |
GOLDSTAR | GVRB455 | N/A | IF POWER GOES OFF FOR ONE SECOND THEN BACK ON, VCR MAY NOT COME BACK ON DUE TO RESET OF PROCESSOR TIME TOO SHORT | CHANGE R248 TO 47k AND C234 TO 10uF @ 50v | |
GOLDSTAR | GVRB455 | N/A | MACHINE SHOWS 'ERROR' WHEN IN THE EJECT MODE | CHECK/REPLACE GEAR 'C' (P/N# 435-256B) OR DRIVE ASSY. (P/N# 435-257B) OR HOUSING ASSY. (P/N# 219-017E) | |
GOLDSTAR | GVRB465 | N/A | INTERMITTENTLY POWER WON'T TURN ON OR OFF WILL REMOTE | ADD C2A1 CAPACITOR (P/N# 0CC6810K405) 680pF | |
GOLDSTAR | GVRB465 | N/A | IF POWER GOES OFF FOR ONE SECOND THEN BACK ON, VCR MAY NOT COME BACK ON DUE TO RESET OF PROCESSOR TIME TOO SHORT | CHANGE R248 TO 47k AND C234 TO 10uF @ 50v | |
GOLDSTAR | GVRB465 | N/A | MACHINE SHOWS 'ERROR' WHEN IN THE EJECT MODE | CHECK/REPLACE GEAR 'C' (P/N# 435-256B) OR DRIVE ASSY. (P/N# 435-257B) OR HOUSING ASSY. (P/N# 219-017E) | |
GOLDSTAR | GVRB465 | N/A | REDUCE AUTO-TRACKING TIME | CHANGE R8A1 TO A 68 | |
GOLDSTAR | GVRB465 | N/A | INTERMITTENT ERROR OR ALARM WHEN GOING FROM ONE MODE TO ANOTHER | CHECK/REPLACE MODE SELECT SWITCH | |
GOLDSTAR | GVRB465 | N/A | REWIND AND FAST FORWARD NOT WORKING | CHECK/REPLACE F/R BRACKET WITH NEW TYPE (P/N# 321-397D) | |
GOLDSTAR | GVRB465 | N/A | DIM DISPLAY | CHANGE R263,R264,R265 AND R266 TO 3.3ohms | |
GOLDSTAR | GVRB465 | N/A | STEREO SOUND LOSES IT'S CLARITY AFTER ON IN THE E-E MODE FOR SEVERAL HOURS | CHANGE R706 TO A 1k AND REMOVE C710 AND REPLACE WITH A SHORT OR PIECE OF WIRE | |
GOLDSTAR | GVRB465 | N/A | AUDIO HUM | CHANGE R3D5 TO 680 (P/N# 0RD6800F608) | |
GOLDSTAR | GVRC235 | N/A | E-E VIDEO LEVEL TOO HIGH | CHANGE R375 TO 6.8k | |
GOLDSTAR | GVRC235 | N/A | IMPROVEMENT OF DRUM AUTO-STOP | ADD A 1N4003 DIODE IN SERIES WITH D203 AND PIN 5 OF PMJ03 - ANODE GOES TO D203's CATHODE AND CATHODE TO PMJ03 PLUG | |
GOLDSTAR | GVRC235 | N/A | BEAT PATTERN ON SCREEN WHEN IN TUNER MODE | ADD C200 (0.022uF @ 25v) (P/N# 0CN2230H948) | |
GOLDSTAR | GVRC235 | N/A | OSD SHAKES IN THE E-E MODE | ADD C782 (100pF @ 50v) TO COLLECTOR OF Q751 TO GROUND (P/N# 0CC1010K412) | |
GOLDSTAR | GVRC245 | N/A | OSD SHAKES IN THE E-E MODE | ADD C782 (100pF @ 50v) TO COLLECTOR OF Q751 TO GROUND (P/N# 0CC1010K412) | |
GOLDSTAR | GVRC245 | N/A | BEAT PATTERN ON SCREEN WHEN IN TUNER MODE | ADD C200 (0.022uF @ 25v) (P/N# 0CN2230H948) | |
GOLDSTAR | GVRC245 | N/A | IMPROVEMENT OF DRUM AUTO-STOP | ADD A 1N4003 DIODE IN SERIES WITH D203 AND PIN 5 OF PMJ03 - ANODE GOES TO D203's CATHODE AND CATHODE TO PMJ03 PLUG | |
GOLDSTAR | GVRC245 | N/A | E-E VIDEO LEVEL TOO HIGH | CHANGE R375 TO 6.8k | |
GOLDSTAR | GVRC435 | N/A | TUNER SHORTED | CHECK/REPLACE TUNER AND TO PREVENT ADD 33v ZENER FROM PIN 7 OF TUNER TO GRD. & 1k 1/6w IN SERIES WITH PIN 7 AND SUPPLY | |
GOLDSTAR | GVRC435 | N/A | SLOW MOTION PICTURE SHAKES | CHANGE R203 TO A 120k | |
GOLDSTAR | GVRC435 | N/A | MODIFICATION TO PROTECT IC503 FROM SURGE CURRENTS | ADD R2A1 3.3 2watt TO PINS#7 AND #8 OF IC503 | |
GOLDSTAR | GVRC435 | N/A | DIAGONAL BEAT PATTERN SEEN INTERMITTENTLY WHEN A TAPE IS PLAYED BACK ON A COLD MACHINE | ADD C388 (0CN1040K948) - 0.1uF @ 50v | |
GOLDSTAR | GVRC447 | N/A | AUDIO HUM | CHANGE R3D5 TO 680 (P/N# 0RD6800F608) | |
GOLDSTAR | GVRC447 | N/A | PICTURE IS DISTORTED IF TEMPERATURE EXCEEDS 45 DEGREES C. | ADD D3A1 (0DD400309AB) (1N4003A) | |
GOLDSTAR | GVRC447 | N/A | BLACK AND WHITE NOISE IN PLAYBACK OF PICTURE | CHANGE R3A7 TO A 1k AND L3A3 TO 220uH (P/N# 0LR2200J025) | |
GOLDSTAR | GVRC447 | N/A | PLAYBACK AUDIO OUTPUT LEVEL IS TO LOAD WHEN COMPARED TO THE TUNER LEVEL | CHANGE R425 TO 12k AND R421 TO 22k | |
GOLDSTAR | GVRC447 | N/A | RECORDED LUMINANCE SIGNAL CURRENT IS TOO HIGH | ADD Q3D1 (0TR103009AE),R3F1 (0RD1001F608) AND CHANGE VALUE OF R3B6 TO 1k (0RD1001F608) | |
GOLDSTAR | GVRC447 | N/A | TUNER SHORTED | REMOVE JUMPER W105 AND REPLACE WITH A 1k RESISTOR (P/N# 0RD1001F608) | |
GOLDSTAR | GVRC447 | N/A | WEAK CHROMA RECORDED ON TAPE | CHANGE R3B5 TO A 2.7k | |
GOLDSTAR | GVRC447 | N/A | BLUE SCREEN DOESN'T ALWAYS APPEAR ON UHF | CHECK/REPLACE C519 (0.01uF @ 100v) | |
GOLDSTAR | GVRC455 | N/A | DIAGONAL BEAT PATTERN SEEN INTERMITTENTLY WHEN A TAPE IS PLAYED BACK ON A COLD MACHINE | ADD C388 (0CN1040K948) - 0.1uF @ 50v | |
GOLDSTAR | GVRC455 | N/A | SLOW MOTION PICTURE SHAKES | CHANGE R203 TO A 120k | |
GOLDSTAR | GVRC465 | N/A | TUNER SHORTED | REMOVE JUMPER W105 AND REPLACE WITH A 1k RESISTOR (P/N# 0RD1001F608) | |
GOLDSTAR | GVRC467 | N/A | AUDIO HUM | CHANGE R3D5 TO 680 (P/N# 0RD6800F608) | |
GOLDSTAR | GVRC467 | N/A | BLACK AND WHITE NOISE IN PLAYBACK OF PICTURE | CHANGE R3A7 TO A 1k AND L3A3 TO 220uH (P/N# 0LR2200J025) | |
GOLDSTAR | GVRC467 | N/A | REDUCE AUTO-TRACKING TIME | CHANGE R8A1 TO A 68 | |
GOLDSTAR | GVRC467 | N/A | TUNER SHORTED | REMOVE JUMPER W105 AND REPLACE WITH A 1k RESISTOR (P/N# 0RD1001F608) | |
GOLDSTAR | GVRC467 | N/A | RECORDED LUMINANCE SIGNAL CURRENT IS TOO HIGH | ADD Q3D1 (0TR103009AE),R3F1 (0RD1001F608) AND CHANGE VALUE OF R3B6 TO 1k (0RD1001F608) & R3B2 TO 390 (0RD3900F608) | |
GOLDSTAR | GVRC467 | N/A | WEAK CHROMA RECORDED ON TAPE | CHANGE R3B5 TO A 2.7k | |
GOLDSTAR | GVRC467 | N/A | PICTURE IS DISTORTED IF TEMPERATURE EXCEEDS 45 DEGREES C. | ADD D3A1 (0DD400309AB) (1N4003A) | |
GOLDSTAR | GVRC467 | N/A | STEREO SOUND LOSES IT'S CLARITY AFTER ON IN THE E-E MODE FOR SEVERAL HOURS | CHANGE R706 TO A 1k AND REMOVE C710 AND REPLACE WITH A SHORT OR PIECE OF WIRE | |
GOLDSTAR | GVRE235 | N/A | PICTURE IS UNSTABLE ON PLAYBACK OF SOME PRE-RECORDED TAPES | CHANGE C334 TO 560pF (P/N# 0CN5610K518) | |
GOLDSTAR | GVRE235 | N/A | COLOR DROPS OUT INTERMITTENTLY ON PLAYBACK OF TAPES | CHANGE C334 TO 560pF (P/N# 0CN5610K518) | |
GOLDSTAR | GVRE235 | N/A | SPEED CHANGES FROM SP-LP-SLP IS ERRATIC | CHANGE R252 TO 1.8k (P/N# 0RD1801F608) AND C233 TO 0.0047uF (P/N# 0CN4720F608) | |
GOLDSTAR | GVRE235 | N/A | VISS SEARCH IS UNSTABLE | CHANGE R224 (P/N# 0RD6802F608) (68k ) | |
GOLDSTAR | GVRE245 | N/A | PICTURE IS UNSTABLE ON PLAYBACK OF SOME PRE-RECORDED TAPES | CHANGE C334 TO 560pF (P/N# 0CN5610K518) | |
GOLDSTAR | GVRE245 | N/A | VISS SEARCH IS UNSTABLE | CHANGE R224 (P/N# 0RD6802F608) (68k ) | |
GOLDSTAR | GVRE245 | N/A | SPEED CHANGES FROM SP-LP-SLP IS ERRATIC | CHANGE R252 TO 1.8k (P/N# 0RD1801F608) AND C233 TO 0.0047uF (P/N# 0CN4720F608) | |
GOLDSTAR | GVRE245 | N/A | COLOR DROPS OUT INTERMITTENTLY ON PLAYBACK OF TAPES | CHANGE C334 TO 560pF (P/N# 0CN5610K518) | |
GOLDSTAR | GVRE435 | N/A | VISS SEARCH IS UNSTABLE | CHANGE R224 (P/N# 0RD6802F608) (68k ) | |
GOLDSTAR | GVRE435 | N/A | PICTURE IS UNSTABLE ON PLAYBACK OF SOME PRE-RECORDED TAPES | CHANGE C334 TO 560pF (P/N# 0CN5610K518) | |
GOLDSTAR | GVRE435 | N/A | COLOR DROPS OUT INTERMITTENTLY ON PLAYBACK OF TAPES | CHANGE C334 TO 560pF (P/N# 0CN5610K518) | |
GOLDSTAR | GVRE435 | N/A | SPEED CHANGES FROM SP-LP-SLP IS ERRATIC | CHANGE R252 TO 1.8k (P/N# 0RD1801F608) AND C233 TO 0.0047uF (P/N# 0CN4720F608) | |
GOLDSTAR | GVRE445 | N/A | COLOR DROPS OUT INTERMITTENTLY ON PLAYBACK OF TAPES | CHANGE C334 TO 560pF (P/N# 0CN5610K518) | |
GOLDSTAR | GVRE445 | N/A | SPEED CHANGES FROM SP-LP-SLP IS ERRATIC | CHANGE R252 TO 1.8k (P/N# 0RD1801F608) AND C233 TO 0.0047uF (P/N# 0CN4720F608) | |
GOLDSTAR | GVRE445 | N/A | VISS SEARCH IS UNSTABLE | CHANGE R224 (P/N# 0RD6802F608) (68k ) | |
GOLDSTAR | GVRE445 | N/A | PICTURE IS UNSTABLE ON PLAYBACK OF SOME PRE-RECORDED TAPES | CHANGE C334 TO 560pF (P/N# 0CN5610K518) | |
GOLDSTAR | GVRE448 | N/A | SPEED CHANGES FROM SP-LP-SLP IS ERRATIC | CHANGE R252 TO 1.8k (P/N# 0RD1801F608) AND C233 TO 0.0047uF (P/N# 0CN4720F608) | |
GOLDSTAR | GVRE448 | N/A | PICTURE IS UNSTABLE ON PLAYBACK OF SOME PRE-RECORDED TAPES | CHANGE C334 TO 560pF (P/N# 0CN5610K518) | |
GOLDSTAR | GVRE448 | N/A | DISTORTED VIDEO FROM TUNER/IF CIRCUIT | CHECK/REPLACE Q7A2 (P/N# 0TR319909AF) OR 2SC3199BL | |
GOLDSTAR | GVRE448 | N/A | VISS SEARCH IS UNSTABLE | CHANGE R224 (P/N# 0RD6802F608) (68k ) | |
GOLDSTAR | GVRE448 | N/A | COLOR DROPS OUT INTERMITTENTLY ON PLAYBACK OF TAPES | CHANGE C334 TO 560pF (P/N# 0CN5610K518) | |
GOLDSTAR | GVRE449 | N/A | VISS SEARCH IS UNSTABLE | CHANGE R224 (P/N# 0RD6802F608) (68k ) | |
GOLDSTAR | GVRE449 | N/A | SPEED CHANGES FROM SP-LP-SLP IS ERRATIC | CHANGE R252 TO 1.8k (P/N# 0RD1801F608) AND C233 TO 0.0047uF (P/N# 0CN4720F608) | |
GOLDSTAR | GVRE455 | N/A | COLOR DROPS OUT INTERMITTENTLY ON PLAYBACK OF TAPES | CHANGE C334 TO 560pF (P/N# 0CN5610K518) | |
GOLDSTAR | GVRE455 | N/A | SPEED CHANGES FROM SP-LP-SLP IS ERRATIC | CHANGE R252 TO 1.8k (P/N# 0RD1801F608) AND C233 TO 0.0047uF (P/N# 0CN4720F608) | |
GOLDSTAR | GVRE455 | N/A | VISS SEARCH IS UNSTABLE | CHANGE R224 (P/N# 0RD6802F608) (68k ) | |
GOLDSTAR | GVRE455 | N/A | PICTURE IS UNSTABLE ON PLAYBACK OF SOME PRE-RECORDED TAPES | CHANGE C334 TO 560pF (P/N# 0CN5610K518) | |
GOLDSTAR | GVRE465 | N/A | VISS SEARCH IS UNSTABLE | CHANGE R224 (P/N# 0RD6802F608) (68k ) | |
GOLDSTAR | GVRE465 | N/A | SPEED CHANGES FROM SP-LP-SLP IS ERRATIC | CHANGE R252 TO 1.8k (P/N# 0RD1801F608) AND C233 TO 0.0047uF (P/N# 0CN4720F608) | |
GOLDSTAR | GVRE465 | N/A | COLOR DROPS OUT INTERMITTENTLY ON PLAYBACK OF TAPES | CHANGE C334 TO 560pF (P/N# 0CN5610K518) | |
GOLDSTAR | GVRE468 | N/A | VISS SEARCH IS UNSTABLE | CHANGE R224 (P/N# 0RD6802F608) (68k ) | |
GOLDSTAR | GVRE468 | N/A | COLOR DROPS OUT INTERMITTENTLY ON PLAYBACK OF TAPES | CHANGE C334 TO 560pF (P/N# 0CN5610K518) | |
GOLDSTAR | GVRE468 | N/A | DISTORTED VIDEO FROM TUNER/IF CIRCUIT | CHECK/REPLACE Q7A2 (P/N# 0TR319909AF) OR 2SC3199BL | |
GOLDSTAR | GVRE468 | N/A | SPEED CHANGES FROM SP-LP-SLP IS ERRATIC | CHANGE R252 TO 1.8k (P/N# 0RD1801F608) AND C233 TO 0.0047uF (P/N# 0CN4720F608) | |
GOLDSTAR | GVRE469 | N/A | SPEED CHANGES FROM SP-LP-SLP IS ERRATIC | CHANGE R252 TO 1.8k (P/N# 0RD1801F608) AND C233 TO 0.0047uF (P/N# 0CN4720F608) | |
GOLDSTAR | GVRE469 | N/A | VISS SEARCH IS UNSTABLE | CHANGE R224 (P/N# 0RD6802F608) (68k ) | |
GOLDSTAR | GVRF455 | N/A | HORZ. INTERFERENCE BAR IN PLAYBACK PICTURE | ADD R399 (33k? BETWEEN IC301, PIN #7 AND THE 5VA LINE | |
GOLDSTAR | VCP100M | N/A | POOR PICTURE LOCK IN THE PLAYBACK MODE | ADD A 47uF @ 16v FROM PIN 25 OF IC201 TO GRD. AND ADD 1k RES. IN SERIES W/C342 ON OPPOSITE SIDE OF PIN 24 | |
GOLDSTAR | VCP100M | N/A | EXCESSIVE WOW AND FLUTTER BEYOND TOLERANCES | CHANGE R211 TO 27k AND R208 TO 120k | |
GOLDSTAR | VCP100M | N/A | UNSTABLE COLOR | CHANGE R323 TO 100k AND C340 TO .22uF | |
GOLDSTAR | VCP100M | N/A | NOISE IN PICTURE FROM MOTOR DRIVER IC | CHANGE C556 TO A 10uF @ 16v ALSO CHECK IC201 FOR DAMAGE DUE TO STATIC | |
GOLDSTAR | VCP105M | N/A | EXCESSIVE WOW AND FLUTTER BEYOND TOLERANCES | CHANGE R211 TO 27k AND R208 TO 120k | |
GOLDSTAR | VCP105M | N/A | POOR PICTURE LOCK IN THE PLAYBACK MODE | ADD A 47uF @ 16v FROM PIN 25 OF IC201 TO GRD. AND ADD 1k RES. IN SERIES W/C342 ON OPPOSITE SIDE OF PIN 24 | |
GOLDSTAR | VCP105M | N/A | UNSTABLE COLOR | CHANGE R323 TO 100k AND C340 TO .22uF | |
GOLDSTAR | VCP105M | N/A | NOISE IN PICTURE FROM MOTOR DRIVER IC | CHANGE C556 TO A 10uF @ 16v ALSO CHECK IC201 FOR DAMAGE DUE TO STATIC | |
GOLDSTAR | VCP106M | N/A | NOISE IN PICTURE FROM MOTOR DRIVER IC | CHANGE C556 TO A 10uF @ 16v ALSO CHECK IC201 FOR DAMAGE DUE TO STATIC | |
GOLDSTAR | VCP106M | N/A | EXCESSIVE WOW AND FLUTTER BEYOND TOLERANCES | CHANGE R211 TO 27k AND R208 TO 120k | |
GOLDSTAR | VCP106M | N/A | POOR PICTURE LOCK IN THE PLAYBACK MODE | ADD A 47uF @ 16v FROM PIN 25 OF IC201 TO GRD. AND ADD 1k RES. IN SERIES W/C342 ON OPPOSITE SIDE OF PIN 24 | |
GOLDSTAR | VCP106M | N/A | UNSTABLE COLOR | CHANGE R323 TO 100k AND C340 TO .22uF | |
GOLDSTAR | VCP4100 | N/A | VIDEO INTERMITTENT--SOUND IS NORMAL | CHECK CONNECTIONS ON VIDEO LEVEL CONTROL (VR301) | |
GOLDSTAR | VCP4100 | N/A | TV RECEPTION IS POOR BUT MAY IMPROVE WHEN VCP IS UNPLUGGED | CHECK C342 FOR REVERSED POLARITY | |
GOLDSTAR | VCP4100M | N/A | NO COLOR ON PLAYBACK | CHECK/REPLACE C359 AND C362 | |
GOLDSTAR | VCP4110M | N/A | CAPSTAN MOTOR WON'T RUN | CHECK/REPLACE IC303,CAPSTAN MOTOR AND CAPACITORS AROUND IC303 | |
GOLDSTAR | VCP4200 | N/A | DELAYED LOCKING TIME | CHANGE C222 FROM 100uF @ 10v TO 47uF @ 10v | |
GOLDSTAR | VCP4206M | N/A | SHUTDOWN AND WON'T EJECT TAPE - INTERMITTENT | CHECK/RESOLDER CONNECTIONS ON CAPSTAN MOTOR CONNECTOR OR LOOSE WIRE ON THAT CONNECTOR | |
GOLDSTAR | VCPH200 | N/A | UNSTABLE COLOR | CHANGE R323 TO 100k AND C340 TO .22uF | |
GOLDSTAR | VCPH200M | N/A | AUDIO DISTORTION ON PLAYBACK BECAUSE OF HIGH RF LEVEL AUDIO | REMOVE C444 AND C447 FROM CIRCUIT | |
GOLDSTAR | VCPH200M | N/A | EXCESSIVE WOW AND FLUTTER | CHANGE R234 TO A 180k AND R238 TO A 27k | |
HARVARD | HVA1001 | N/A | WHITE NOISE LINE APPEARS WITHIN 3 SECS. OF PLAY | ADD 1.5 MEG OHM BETWEEN PIN#11 OF IC202 AND GROUND | |
HITACHI | VT1100A | N/A | INTERMITTENT SHUTOFF - NO POWER OR DISPLAY | CHECK/REPLACE IC802 (HA7935) | |
HITACHI | VT1100A | N/A | WILL NOT PLAY AT CORRECT SPEED OR INTERMITTENTLY CHANGES SPEED OF SELF/PRE-RECORDED TAPES | CHECK/REPLACE AUDIO/CTRL HEAD (P/N 5446161) | |
HITACHI | VT1105A | N/A | WILL NOT PLAY AT CORRECT SPEED OR INTERMITTENTLY CHANGES SPEED OF SELF/PRE-RECORDED TAPES | CHECK/REPLACE AUDIO/CTRL HEAD (P/N 5446161) | |
HITACHI | VT1110A | N/A | WILL NOT PLAY AT CORRECT SPEED OR INTERMITTENTLY CHANGES SPEED OF SELF/PRE-RECORDED TAPES | CHECK/REPLACE AUDIO/CTRL HEAD (P/N 5446161) | |
HITACHI | VT11A | N/A | AUDIO SQUEAL IN PLAYBACK | CHECK/REPLACE RL401 RELAY | |
HITACHI | VT11A | N/A | NO SPEED SELECT | IC601 | |
HITACHI | VT1200A | N/A | WILL NOT PLAY AT CORRECT SPEED OR INTERMITTENTLY CHANGES SPEED OF SELF/PRE-RECORDED TAPES | CHECK/REPLACE AUDIO/CTRL HEAD (P/N 5446161) | |
HITACHI | VT1210A | N/A | WILL NOT PLAY AT CORRECT SPEED OR INTERMITTENTLY CHANGES SPEED OF SELF/PRE-RECORDED TAPES | CHECK/REPLACE AUDIO/CTRL HEAD (P/N 5446161) | |
HITACHI | VT1300A | N/A | NO RECORD FM AT PIN 20 OF IC205 | CHECK/REPLACE IC206 | |
HITACHI | VT1300A | N/A | WILL NOT PLAY AT CORRECT SPEED OR INTERMITTENTLY CHANGES SPEED OF SELF/PRE-RECORDED TAPES | CHECK/REPLACE AUDIO/CTRL HEAD (P/N 5446161) | |
HITACHI | VT1300A | N/A | INTERMITTENT SHUTOFF - NO POWER OR DISPLAY | CHECK/REPLACE IC802 (HA7935) | |
HITACHI | VT1310A | N/A | GOES INTO PLAY BUT TAKE-UP REEL WON'T TURN | CHECK THE PIN IN THE ARM THAT OPERATES PINCH ROLLER FOR DROPPING OUT - REPLACE ARM | |
HITACHI | VT1310A | N/A | PLAYS VERY FAST-LOOKS LIKE NO SPEED SELECT | PINCH ROLLER DOESN'T COME IN CONTACT WITH THE CAPSTAN SHAFT--CHECK TAPE GUIDE TO THE RIGHT OF CAPSTAN. | |
HITACHI | VT1310A | N/A | WILL NOT PLAY AT CORRECT SPEED OR INTERMITTENTLY CHANGES SPEED OF SELF/PRE-RECORDED TAPES | CHECK/REPLACE AUDIO/CTRL HEAD (P/N 5446161) | |
HITACHI | VT1310A | N/A | BARS OF COLOR - BLACK AND WHITE PICTURE MOVING UP THE SCREEN - DRUM WILL NOT RUN | CHECK/REPLACE IC51 | |
HITACHI | VT1310A | N/A | DRUM WILL NOT RUN | CHECK/REPLACE REGULATOR IC (STK5471) | |
HITACHI | VT1315A | N/A | WILL NOT PLAY AT CORRECT SPEED OR INTERMITTENTLY CHANGES SPEED OF SELF/PRE-RECORDED TAPES | CHECK/REPLACE AUDIO/CTRL HEAD (P/N 5446161) | |
HITACHI | VT1320A | N/A | WILL NOT PLAY AT CORRECT SPEED OR INTERMITTENTLY CHANGES SPEED OF SELF/PRE-RECORDED TAPES | CHECK/REPLACE AUDIO/CTRL HEAD (P/N 5446161) | |
HITACHI | VT1350A | N/A | WILL NOT PLAY AT CORRECT SPEED OR INTERMITTENTLY CHANGES SPEED OF SELF/PRE-RECORDED TAPES | CHECK/REPLACE AUDIO/CTRL HEAD (P/N 5446161) | |
HITACHI | VT1370A | N/A | WILL NOT PLAY AT CORRECT SPEED OR INTERMITTENTLY CHANGES SPEED OF SELF/PRE-RECORDED TAPES | CHECK/REPLACE AUDIO/CTRL HEAD (P/N 5446161) | |
HITACHI | VT1400A | N/A | UNIT SHUTSDOWN IN PLAYBACK OR RECORD | CHECK/REPLACE LOWER DRUM ASSY IF MISSING 30Hz SWITCH PULSE | |
HITACHI | VT1400A | N/A | BARS OF COLOR - BLACK AND WHITE PICTURE MOVING UP THE SCREEN - DRUM WILL NOT RUN | CHECK/REPLACE IC51 | |
HITACHI | VT1450A | N/A | PLAYS VERY FAST-LOOKS LIKE NO SPEED SELECT | PINCH ROLLER DOESN'T COME IN CONTACT WITH THE CAPSTAN SHAFT--CHECK TAPE GUIDE TO THE RIGHT OF CAPSTAN. | |
HITACHI | VT2005A | N/A | NO OR VERY DARK E-E VIDEO | CHECK/REPLACE IC201 (INTERNAL COLD SOLDER JOINTS) | |
HITACHI | VT2005A | N/A | FUSE F852 AND F853 BLOW | CHECK/REPLACE ZD862 WITH A 30v ZENER (P/N 5339256) | |
HITACHI | VT2500 | N/A | INTERMITTENT EJECT DUE TO A DEFORMED FL CHANGE GEAR | CHECK/REPLACE WITH NEW PART # 6896954 | |
HITACHI | VT2600 | N/A | INTERMITTENT EJECT DUE TO A DEFORMED FL CHANGE GEAR | CHECK/REPLACE WITH NEW PART # 6896954 | |
HITACHI | VT2605 | N/A | INTERMITTENT EJECT DUE TO A DEFORMED FL CHANGE GEAR | CHECK/REPLACE WITH NEW PART # 6896954 | |
HITACHI | VT2700 | N/A | INTERMITTENT EJECT DUE TO A DEFORMED FL CHANGE GEAR | CHECK/REPLACE WITH NEW PART # 6896954 | |
HITACHI | VT2805 | N/A | NO DISPLAY | CHECK/REPLACE QF801,IC804,R852 AND D802 | |
HITACHI | VT2805 | N/A | 5 VOLT REGULATOR OUTPUT IS LOW | CHECK/REPLACE Q871 AND Q872 AND C870 | |
HITACHI | VT2805 | N/A | INTERMITTENT EJECT DUE TO A DEFORMED FL CHANGE GEAR | CHECK/REPLACE WITH NEW PART # 6896954 | |
HITACHI | VT2805A | N/A | VISS INDEXING NOT WORKING | CHECK/RESOLDER CONNECTIONS ON BIG PWB TO SMALL PWB ON REGULATOR | |
HITACHI | VT2805A | N/A | FUSE F852 AND F853 BLOW | CHECK/REPLACE ZD862 WITH A 30v ZENER (P/N 5339256) | |
HITACHI | VT3000 | N/A | INTERMITTENT EJECT DUE TO A DEFORMED FL CHANGE GEAR | CHECK/REPLACE WITH NEW PART # 6896954 | |
HITACHI | VT3000A | N/A | TRACKING NOISE - NO CAPSTAN PHASE LOCK WHEN PLAYING BACK OF SELF-RECORDED TAPES | CHANGE R641 TO A 560 ohm - IF THIS DOESN'T SOLVE THEN REPLACE THE AUDIO/CTRL HEAD. | |
HITACHI | VT3000A | N/A | NO COLOR OR COLOR FLASH AT HIGH TEMPERATURE AREAS | CHECK/REPLACE IC202 (P/N 1380133) | |
HITACHI | VT3000A | N/A | MIS-TUNING DURING TIMER OPERATION | CHECK ALIGNMENT OF RT501 (15.7 khz ADJUSTMENT) | |
HITACHI | VT3000A | N/A | WILL NOT AUTO-PROGRAM | CHECK/REPLACE IC501 | |
HITACHI | VT3005 | N/A | INTERMITTENT EJECT DUE TO A DEFORMED FL CHANGE GEAR | CHECK/REPLACE WITH NEW PART # 6896954 | |
HITACHI | VT3010 | N/A | INTERMITTENT EJECT DUE TO A DEFORMED FL CHANGE GEAR | CHECK/REPLACE WITH NEW PART # 6896954 | |
HITACHI | VT3011 | N/A | INTERMITTENT EJECT DUE TO A DEFORMED FL CHANGE GEAR | CHECK/REPLACE WITH NEW PART # 6896954 | |
HITACHI | VT3012 | N/A | INTERMITTENT EJECT DUE TO A DEFORMED FL CHANGE GEAR | CHECK/REPLACE WITH NEW PART # 6896954 | |
HITACHI | VT3012A | N/A | CAPSTAN/CYL. JERKS IN PLAY-CAPSTAN JERKS IN REW/FF | CHECK FOR BREAK BETWEEN PIN 1 OF IC202 AND C601 | |
HITACHI | VT3012A | N/A | CAPSTAN RUNS IN THE EJECT MODE-OR WON'T RUN AT ALL | CHECK FOR A DEFECTIVE CAPSTAN MOTOR | |
HITACHI | VT3012A | N/A | COUNTER RUNS VERY FAST WITH OR WITHOUT A TAPE IN PLACE | CHECK/RESOLDER CONNECTIONS ON IC751 (PINS 25-40) | |
HITACHI | VT3012A | N/A | HUM BAR IN THE VIDEO AND LOUD BUZZ IN AUDIO | CHECK/REPLACE C866 | |
HITACHI | VT3012A | N/A | NO COLOR IN THE RECORD MODE IN ALL SPEEDS - PLAYBACK OK | CHECK/REPLACE HEAD PREAMP/HEAD SWITCHING MODULE | |
HITACHI | VT3012A | N/A | WILL NOT EJECT INTERMITTENTLY | CHECK/REPLACE C864 (100 F @ 50v) | |
HITACHI | VT3012A | N/A | NO SOUND ON RECORD - PLAYBACK OF PRE-RECORDED TAPES OK | CHECK/REPLACE Q401 (P/N# 177112 OR ECG2361) | |
HITACHI | VT3012A | N/A | PLAYBACK CHROMA IS MISSING | CHECK IC401 | |
HITACHI | VT3012A | N/A | DEAD - BLOWS FU852 FUSE - IC753 GETS HOT | CHECK FOR A JAMMED OR MIS-ALIGNED MECHANISM | |
HITACHI | VT3012A | N/A | NO DISPLAY | CHECK/REPLACE ZD861 (30 VOLT ZENER) FOR SHORT | |
HITACHI | VT3014 | N/A | INTERMITTENT EJECT DUE TO A DEFORMED FL CHANGE GEAR | CHECK/REPLACE WITH NEW PART # 6896954 | |
HITACHI | VT3015 | N/A | INTERMITTENT EJECT DUE TO A DEFORMED FL CHANGE GEAR | CHECK/REPLACE WITH NEW PART # 6896954 | |
HITACHI | VT3040 | N/A | INTERMITTENT EJECT DUE TO A DEFORMED FL CHANGE GEAR | CHECK/REPLACE WITH NEW PART # 6896954 | |
HITACHI | VT3040A | N/A | NO TUNER AUDIO | CHECK/RESOLDER CONNECTIONS ON R553 | |
HITACHI | VT3044 | N/A | INTERMITTENT EJECT DUE TO A DEFORMED FL CHANGE GEAR | CHECK/REPLACE WITH NEW PART # 6896954 | |
HITACHI | VT3045 | N/A | INTERMITTENT EJECT DUE TO A DEFORMED FL CHANGE GEAR | CHECK/REPLACE WITH NEW PART # 6896954 | |
HITACHI | VT3046 | N/A | INTERMITTENT EJECT DUE TO A DEFORMED FL CHANGE GEAR | CHECK/REPLACE WITH NEW PART # 6896954 | |
HITACHI | VT3048 | N/A | INTERMITTENT EJECT DUE TO A DEFORMED FL CHANGE GEAR | CHECK/REPLACE WITH NEW PART # 6896954 | |
HITACHI | VT3050 | N/A | HUM BAR IN THE VIDEO AND LOUD BUZZ IN AUDIO | CHECK/REPLACE C866 | |
HITACHI | VT3050 | N/A | INTERMITTENT EJECT DUE TO A DEFORMED FL CHANGE GEAR | CHECK/REPLACE WITH NEW PART # 6896954 | |
HITACHI | VT3050A | N/A | CAPSTAN MOTOR RUNS ALL THE TIME,RUNS TOO FAST IN PLAY,DRUM MAY ALSO RUN ALL THE TIME | CHECK FOR RESET AT PIN 1 OF IC1722 | |
HITACHI | VT3060 | N/A | INTERMITTENT EJECT DUE TO A DEFORMED FL CHANGE GEAR | CHECK/REPLACE WITH NEW PART # 6896954 | |
HITACHI | VT3100 | N/A | INTERMITTENT EJECT DUE TO A DEFORMED FL CHANGE GEAR | CHECK/REPLACE WITH NEW PART # 6896954 | |
HITACHI | VT3101 | N/A | INTERMITTENT EJECT DUE TO A DEFORMED FL CHANGE GEAR | CHECK/REPLACE WITH NEW PART # 6896954 | |
HITACHI | VT3106 | N/A | INTERMITTENT EJECT DUE TO A DEFORMED FL CHANGE GEAR | CHECK/REPLACE WITH NEW PART # 6896954 | |
HITACHI | VT33A | N/A | INTERMITTENT SHUTDOWN | CHECK/REPLACE D481 | |
HITACHI | VT33A | N/A | INTERMITTENT SHUTDOWN,UNIT STOPS AND GOES INTO REWIND | CHECK/REPLACE INTERMITTENT END SENSORS | |
HITACHI | VT33A | N/A | INTERMITTENT ERRATIC OPERATION OF INPUT KEYS (MAY GO TO REWIND WHEN STOP KEY IS PRESSED) | CHECK/REPLACE DIRTY INPUT KEYS (WHICH SENDS THE WRONG RESISTANCE TO THE A/D CONVERTER) | |
HITACHI | VT3400 | N/A | INTERMITTENT EJECT DUE TO A DEFORMED FL CHANGE GEAR | CHECK/REPLACE WITH NEW PART # 6896954 | |
HITACHI | VT3400A | N/A | NO COLOR OR COLOR FLASH AT HIGH TEMPERATURE AREAS | CHECK/REPLACE IC202 (P/N 1380144) | |
HITACHI | VT3600 | N/A | INTERMITTENT EJECT DUE TO A DEFORMED FL CHANGE GEAR | CHECK/REPLACE WITH NEW PART # 6896954 | |
HITACHI | VT3800 | N/A | INTERMITTENT EJECT DUE TO A DEFORMED FL CHANGE GEAR | CHECK/REPLACE WITH NEW PART # 6896954 | |
HITACHI | VT3805 | N/A | INTERMITTENT EJECT DUE TO A DEFORMED FL CHANGE GEAR | CHECK/REPLACE WITH NEW PART # 6896954 | |
HITACHI | VT39EM | N/A | NO CLOCK DISPLAY,TUNING PROBLEMS,RADIATED LINES IN PIX, DISPLAY TOO BRIGHT OR TOO DARK | CHECK/REPLACE C741,C724,C744 AND DC-DC CONV. (P/N 5261191) | |
HITACHI | VT56 | N/A | UNIT SHOWS A TAPE IS IN VCR WHEN THERE IS NONE IN IT | CHECK/REPLACE START AND END SENSORS ON CARRIAGE (RCA P/N# 161757) | |
HITACHI | VT56A | N/A | NO CLOCK DISPLAY,TUNING PROBLEMS,RADIATED LINES IN PIX, DISPLAY TOO BRIGHT OR TOO DARK | CHECK/REPLACE C1702,C1706,C1708 AND DC-DC CONV(P/N 7022481) | |
HITACHI | VT61A | N/A | NO CLOCK DISPLAY,TUNING PROBLEMS,RADIATED LINES IN PIX, DISPLAY TOO BRIGHT OR TOO DARK | CHECK/REPLACE C806,C807,C805 AND DC-DC CONV(P/N 5262081) | |
HITACHI | VT62A | N/A | NO CLOCK DISPLAY,TUNING PROBLEMS,RADIATED LINES IN PIX, DISPLAY TOO BRIGHT OR TOO DARK | CHECK/REPLACE C806,C807,C805 AND DC-DC CONV(P/N 5262081) | |
HITACHI | VT63 | N/A | UNIT SHOWS A TAPE IS IN VCR WHEN THERE IS NONE IN IT | CHECK/REPLACE START AND END SENSORS ON CARRIAGE (RCA P/N# 161757) | |
HITACHI | VT63A | N/A | UNIT THINKS THAT A TAPE IS INSERTED | REPLACE BOTH TAPE END SENSORS | |
HITACHI | VT63A | N/A | INTERFERRENCE IN VIDEO-ESPECIALLY HIGH CHANNELS | APPEARS TO BE RADIATION--REPL.(2) 47uF @ 50 (DC-DC) | |
HITACHI | VT63A | N/A | CHANNELS CYCLE AFTER CHANNEL UP/DOWN BUTTONS ARE PRESSED | CHECK/RESOLDER CONNECTIONS ON GROUND AND SPRING INSIDE REMOTE RECEIVER | |
HITACHI | VT63A | N/A | NO DISPLAY | DC-DC CONVERTER BAD-REPL. (2) OPEN 47uF CAPACITORS | |
HITACHI | VT63A | N/A | DRUM MOTOR WON'T START INTERMITTENTLY | CHECK FOR COLD SOLDER CONNECTIONS ON D617 AND D618 | |
HITACHI | VT63A | N/A | AFTER EJECTING A TAPE, CARRIAGE WILL TRY TO LOAD AGAIN | CHECK/REPLACE Q142 TAKE-UP SENSOR (P/N# 161757) | |
HITACHI | VT63A | N/A | INTERFERRENCE IN VIDEO-ESPECIALLY HIGH CHANNELS | APPEARS TO BE RADIATION--REPL.(2) 47uF @ 50 (DC-DC) | |
HITACHI | VT63A | N/A | POWER SUPPLY BLOWS FUSES IMMEDIATELY-DIODES OK | CHECK C854 AND C860 SHORTED | |
HITACHI | VT63A | N/A | UNIT THINKS THAT A TAPE IS INSERTED | REPLACE BOTH TAPE END SENSORS | |
HITACHI | VT63A | N/A | CAPSTAN MOTOR WILL NOT RUN | CHECK/REPLACE R631 FOR OPEN - ALSO INSPECT THE CAPSTAN FLYWHEEL BEARINGS FOR LUBRICATION | |
HITACHI | VT63A | N/A | POWER SUPPLY BLOWS FUSES IMMEDIATELY-DIODES OK | CHECK C854 AND C860 SHORTED | |
HITACHI | VT63A | N/A | AFTER EJECTING A TAPE, CARRIAGE WILL TRY TO LOAD AGAIN | CHECK/REPLACE Q142 TAKE-UP SENSOR (P/N# 161757) | |
HITACHI | VT63A | N/A | CAPSTAN SPEED IS OFF - TOO SLOW ON SP AND TOO FAST ON SLP | CHECK/REPLACE IC604 -CHECK PWM OUTPUT ON PIN#10 AND PIN#15 OF IC604 FOR PWM OUTPUT. | |
HITACHI | VT63A | N/A | NO CLOCK DISPLAY,TUNING PROBLEMS,RADIATED LINES IN PIX, DISPLAY TOO BRIGHT OR TOO DARK | CHECK/REPLACE C806,C807,C805 AND DC-DC CONV(P/N 5262081) | |
HITACHI | VT63A | N/A | CAPSTAN MOTOR WILL NOT RUN | CHECK/REPLACE R631 FOR OPEN - ALSO INSPECT THE CAPSTAN FLYWHEEL BEARINGS FOR LUBRICATION | |
HITACHI | VT63A | N/A | NO DISPLAY | DC-DC CONVERTER BAD-REPL. (2) OPEN 47uF CAPACITORS | |
HITACHI | VT63A | N/A | DRUM MOTOR WON'T START INTERMITTENTLY | CHECK FOR COLD SOLDER CONNECTIONS ON D617 AND D618 | |
HITACHI | VT63A | N/A | CAPSTAN SPEED IS OFF - TOO SLOW ON SP AND TOO FAST ON SLP | CHECK/REPLACE IC604 -CHECK PWM OUTPUT ON PIN#10 AND PIN#15 OF IC604 FOR PWM OUTPUT. | |
HITACHI | VT64 | N/A | UNIT SHOWS A TAPE IS IN VCR WHEN THERE IS NONE IN IT | CHECK/REPLACE START AND END SENSORS ON CARRIAGE (RCA P/N# 161757) | |
HITACHI | VT64A | N/A | POWER SUPPLY BLOWS FUSES IMMEDIATELY-DIODES OK | CHECK C854 AND C860 SHORTED | |
HITACHI | VT64A | N/A | UNIT THINKS THAT A TAPE IS INSERTED | REPLACE BOTH TAPE END SENSORS | |
HITACHI | VT64A | N/A | NO DISPLAY | DC-DC CONVERTER BAD-REPL. (2) OPEN 47uF CAPACITORS | |
HITACHI | VT64A | N/A | CAPSTAN MOTOR WILL NOT RUN | CHECK/REPLACE R631 FOR OPEN - ALSO INSPECT THE CAPSTAN FLYWHEEL BEARINGS FOR LUBRICATION | |
HITACHI | VT64A | N/A | INTERFERRENCE IN VIDEO-ESPECIALLY HIGH CHANNELS | APPEARS TO BE RADIATION--REPL.(2) 47uF @ 50 (DC-DC) | |
HITACHI | VT64A | N/A | DRUM MOTOR WON'T START INTERMITTENTLY | CHECK FOR COLD SOLDER CONNECTIONS ON D617 AND D618 | |
HITACHI | VT64A | N/A | AFTER EJECTING A TAPE, CARRIAGE WILL TRY TO LOAD AGAIN | CHECK/REPLACE Q142 TAKE-UP SENSOR (P/N# 161757) | |
HITACHI | VT64A | N/A | CAPSTAN SPEED IS OFF - TOO SLOW ON SP AND TOO FAST ON SLP | CHECK/REPLACE IC604 -CHECK PWM OUTPUT ON PIN#10 AND PIN#15 OF IC604 FOR PWM OUTPUT. | |
HITACHI | VT65 | N/A | UNIT SHOWS A TAPE IS IN VCR WHEN THERE IS NONE IN IT | CHECK/REPLACE START AND END SENSORS ON CARRIAGE (RCA P/N# 161757) | |
HITACHI | VT65A | N/A | NO CLOCK DISPLAY,TUNING PROBLEMS,RADIATED LINES IN PIX, DISPLAY TOO BRIGHT OR TOO DARK | CHECK/REPLACE C806,C802,C810 AND DC-DC CONV(P/N 5261192) | |
HITACHI | VT71 | N/A | UNIT SHOWS A TAPE IS IN VCR WHEN THERE IS NONE IN IT | CHECK/REPLACE START AND END SENSORS ON CARRIAGE (RCA P/N# 161757) | |
HITACHI | VT71A | N/A | NO CLOCK DISPLAY,TUNING PROBLEMS,RADIATED LINES IN PIX, DISPLAY TOO BRIGHT OR TOO DARK | CHECK/REPLACE C806,C807,C805 AND DC-DC CONV(P/N 5262081) | |
HITACHI | VT73 | N/A | UNIT SHOWS A TAPE IS IN VCR WHEN THERE IS NONE IN IT | CHECK/REPLACE START AND END SENSORS ON CARRIAGE (RCA P/N# 161757) | |
HITACHI | VT73AY | N/A | NO CLOCK DISPLAY,TUNING PROBLEMS,RADIATED LINES IN PIX, DISPLAY TOO BRIGHT OR TOO DARK | CHECK/REPLACE C806,C807,C805 AND DC-DC CONV(P/N 5262081) | |
HITACHI | VT74 | N/A | UNIT SHOWS A TAPE IS IN VCR WHEN THERE IS NONE IN IT | CHECK/REPLACE START AND END SENSORS ON CARRIAGE (RCA P/N# 161757) | |
HITACHI | VT74A | N/A | NO DISPLAY | DC-DC CONVERTER BAD-REPL. (2) OPEN 47uF CAPACITORS | |
HITACHI | VT74A | N/A | UNIT THINKS THAT A TAPE IS INSERTED | REPLACE BOTH TAPE END SENSORS | |
HITACHI | VT74A | N/A | DRUM MOTOR WON'T START INTERMITTENTLY | CHECK FOR COLD SOLDER CONNECTIONS ON D617 AND D618 | |
HITACHI | VT74A | N/A | AFTER EJECTING A TAPE, CARRIAGE WILL TRY TO LOAD AGAIN | CHECK/REPLACE Q142 TAKE-UP SENSOR (P/N# 161757) | |
HITACHI | VT74A | N/A | CAPSTAN MOTOR WILL NOT RUN | CHECK/REPLACE R631 FOR OPEN - ALSO INSPECT THE CAPSTAN FLYWHEEL BEARINGS FOR LUBRICATION | |
HITACHI | VT74A | N/A | INTERFERRENCE IN VIDEO-ESPECIALLY HIGH CHANNELS | APPEARS TO BE RADIATION--REPL.(2) 47uF @ 50 (DC-DC) | |
HITACHI | VT74A | N/A | POWER SUPPLY BLOWS FUSES IMMEDIATELY-DIODES OK | CHECK C854 AND C860 SHORTED | |
HITACHI | VT74A | N/A | CAPSTAN SPEED IS OFF - TOO SLOW ON SP AND TOO FAST ON SLP | CHECK/REPLACE IC604 -CHECK PWM OUTPUT ON PIN#10 AND PIN#15 OF IC604 FOR PWM OUTPUT. | |
HITACHI | VT74AY | N/A | NO CLOCK DISPLAY,TUNING PROBLEMS,RADIATED LINES IN PIX, DISPLAY TOO BRIGHT OR TOO DARK | CHECK/REPLACE C806,C807,C805 AND DC-DC CONV(P/N 5262081) | |
HITACHI | VT76AY | N/A | NO CLOCK DISPLAY,TUNING PROBLEMS,RADIATED LINES IN PIX, DISPLAY TOO BRIGHT OR TOO DARK | CHECK/REPLACE C806,C802,C810 AND DC-DC CONV(P/N 5261192) | |
HITACHI | VT78 | N/A | UNIT SHOWS A TAPE IS IN VCR WHEN THERE IS NONE IN IT | CHECK/REPLACE START AND END SENSORS ON CARRIAGE (RCA P/N# 161757) | |
HITACHI | VT78AY | N/A | NO CLOCK DISPLAY,TUNING PROBLEMS,RADIATED LINES IN PIX, DISPLAY TOO BRIGHT OR TOO DARK | CHECK/REPLACE C803,C805,C806 AND DC-DC CONV(P/N 5261192) | |
HITACHI | VT7A | N/A | MOTORBOATING IN PLAYBACK | CHECK/RESOLDER CONNECTIONS ON FEEDTHRU FROM PIN 14 OF IC402 TO PIN 2 OF IC403 | |
HITACHI | VT7A | N/A | AUDIO IS MUTED AND NO SEARCH FUNCTION | CHECK/REPLACE IC803 | |
HITACHI | VT7A | N/A | INTERMITTENT CAPSTAN START OR RUN | CHECK/REPLACE D920 FOR LEAKAGE | |
HITACHI | VT7A | N/A | DRUM OR CAPSTAN DOESN'T TURN | CHECK/REPLACE END SENSOR AND MISSING 3.58mhz REFERENCE TO SERVO CIRCUIT | |
HITACHI | VT7A | N/A | INTERMITTENT SPEED CHANGES IN PLAYBACK | MODIFY GROMMETS ON BOTTOM COVER WITH SCOTCH TAPE DUE TO THEM BECOMING CONDUCTIVE | |
HITACHI | VT86A | N/A | NO CLOCK DISPLAY,TUNING PROBLEMS,RADIATED LINES IN PIX, DISPLAY TOO BRIGHT OR TOO DARK | CHECK/REPLACE C803,C805,C806 AND DC-DC CONV(P/N 5261192) | |
HITACHI | VT87A | N/A | NO CLOCK DISPLAY,TUNING PROBLEMS,RADIATED LINES IN PIX, DISPLAY TOO BRIGHT OR TOO DARK | CHECK/REPLACE C819,C816,C824 AND DC-DC CONV(P/N 5261193) | |
HITACHI | VT88A | N/A | NO DISPLAY OR DIM DISPLAY | CHECK/REPLACE C1201 | |
HITACHI | VT88A | N/A | CARRIAGE CONTINUOUSLY LOADS | CHECK/REPLACE CAM GEARS ON CARRIAGE (P/N LEFT 6870851 AND RIGHT 6870861) | |
HITACHI | VT88A | N/A | STATIC NOISE IN FM AUDIO PLAYBACK | CHECK/REPLACE C2028 AND C2029 | |
HITACHI | VT89A | N/A | NO CLOCK DISPLAY,TUNING PROBLEMS,RADIATED LINES IN PIX, DISPLAY TOO BRIGHT OR TOO DARK | CHECK/REPLACE C1731,C1729,C1732 AND DC-DC CONV(P/N 5262042) | |
HITACHI | VT89A | N/A | REEL MOTOR DOESN'T RUN IN PLAY | CHECK/REPLACE D872 FOR LEAKAGE | |
HITACHI | VT89A | N/A | OSD SHOWS PAC-MAN CHARACTERS | CHECK/REPLACE IC102 | |
HITACHI | VT89A | N/A | NO DISPLAY | CHECK/REPLACE D106 FOR OPEN | |
HITACHI | VT89A | N/A | NO DISPLAY | CHECK/REPLACE D1714 FOR OPEN | |
HITACHI | VT94A | N/A | NO CLOCK DISPLAY,TUNING PROBLEMS,RADIATED LINES IN PIX, DISPLAY TOO BRIGHT OR TOO DARK | CHECK/REPLACE C723,C719,C722,C713 AND DC-DC CONVERTER (P/N 5261191) | |
HITACHI | VT98A | N/A | NO CLOCK DISPLAY,TUNING PROBLEMS,RADIATED LINES IN PIX, DISPLAY TOO BRIGHT OR TOO DARK | CHECK/REPLACE C627,C622 AND DC-DC CONV. (P/N 5261191) | |
HITACHI | VTF320 | N/A | INTERMITTENT EJECT DUE TO A DEFORMED FL CHANGE GEAR | CHECK/REPLACE WITH NEW PART # 6804834 | |
HITACHI | VTF330 | N/A | INTERMITTENT EJECT DUE TO A DEFORMED FL CHANGE GEAR | CHECK/REPLACE WITH NEW PART # 6804834 | |
HITACHI | VTF330 | N/A | UNIT SHUTS OFF ON PLAY AND RECORD | CHECK/REPLACE Q862 | |
HITACHI | VTF330A | N/A | WILL NOT LOAD TAPE AND SHUTS POWER OFF | CHECK/REPLACE Q862 FOR LEAKAGE | |
HITACHI | VTF330A | N/A | POOR TRACKING - PIX PULSATES GOOD/BAD/GOOD/BAD - GOES TO BLUE SCREEN INTERMITTENTLY | CHECK LUBRICATION ON THE HALF LOAD ARM - IF STUCK IN THE WRONG POSITION,CTRL. HEAD WON'T READ TAPE. | |
HITACHI | VTF333 | N/A | INTERMITTENT EJECT DUE TO A DEFORMED FL CHANGE GEAR | CHECK/REPLACE WITH NEW PART # 6804834 | |
HITACHI | VTF350 | N/A | DEAD | CHECK/REPLACE 1.6A FUSE AND D853 AND D854 | |
HITACHI | VTF350A | N/A | 1/2 OF PLAYBACK PICTURE HAS NO CHROMA AND HORZ. JITTER | CHECK/REPLACE DRUM MOTOR ASSY. (NO TACH PULSE TO SERVO IC) | |
HITACHI | VTF350A | N/A | DISTORTED HI-FI AUDIO AND E-E AUDIO | CHECK/REPLACE MPX IC (SBX1637-01) | |
HITACHI | VTF351 | N/A | DEAD | CHECK/REPLACE 1.6A FUSE AND D853 AND D854 | |
HITACHI | VTF351 | N/A | WILL NOT LOAD A TAPE | CHECK/REPLACE LOADING IC501 (P/N# 1342031) | |
HITACHI | VTF361 | N/A | WILL NOT ACCEPT A TAPE | CHECK/REPLACE R967 | |
HITACHI | VTF361A | N/A | DRUM MOTOR RUNS CONTINOUSLY | CHECK/REPLACE IC601 (P/N# 1345871) | |
HITACHI | VTF361A | N/A | CAPSTAN BELT SLIPS OFF AND BELT MAY BE WARPED OUT OF SHAPE | CHECK/REPLACE NEW BELT AND PULLEY KIT (P/N# 4589072) | |
HITACHI | VTF361A | N/A | ABNORMAL GEAR NOISE DURING LOADING AND UNLOADING | CHECK/REPLACE WORM GEAR WITH NEW TYPE (P/N# 6816211) | |
HITACHI | VTF361A | N/A | RANDOM CHROMA BARS AT THE TOP OF THE SCREEN DURING PLAYBACK | CHANGE R227 TO A 5.6k (P/N# 0700051) | |
HITACHI | VTF361A | N/A | HIGH PITCHED SQUEAL AND LINES OF INTERFERENCE IN PICTURE WHEN PLAYING SELF RECORDED TAPES | CHECK/REPLACE Q401 (P/N# 5327101) | |
HITACHI | VTF361A | N/A | ABNORMAL GEAR NOISE DURING LOADING AND UNLOADING | CHECK/REPLACE LOADING MOTOR WORM GEAR | |
HITACHI | VTF361A | N/A | OLD AUDIO AND VIDEO IS NOT BEING ERASED | CHECK/REPLACE IC401 | |
HITACHI | VTF362A | N/A | RANDOM CHROMA BARS AT THE TOP OF THE SCREEN DURING PLAYBACK | CHANGE C227 TO A 0.0033uF (P/N# 0890038) | |
HITACHI | VTF362A | N/A | ABNORMAL GEAR NOISE DURING LOADING AND UNLOADING | CHECK/REPLACE WORM GEAR WITH NEW TYPE (P/N# 6816211) | |
HITACHI | VTF362A | N/A | CAPSTAN BELT SLIPS OFF AND BELT MAY BE WARPED OUT OF SHAPE | CHECK/REPLACE NEW BELT AND PULLEY KIT (P/N# 4589072) | |
HITACHI | VTF362A | N/A | ABNORMAL GEAR NOISE DURING LOADING AND UNLOADING | CHECK/REPLACE LOADING MOTOR WORM GEAR | |
HITACHI | VTF365 | N/A | WILL NOT ACCEPT A TAPE | CHECK/REPLACE R967 | |
HITACHI | VTF365AW | N/A | RANDOM CHROMA BARS AT THE TOP OF THE SCREEN DURING PLAYBACK | CHANGE R227 TO A 5.6k (P/N# 0700051) | |
HITACHI | VTF365AW | N/A | ABNORMAL GEAR NOISE DURING LOADING AND UNLOADING | CHECK/REPLACE LOADING MOTOR WORM GEAR | |
HITACHI | VTF365AW | N/A | CAPSTAN BELT SLIPS OFF AND BELT MAY BE WARPED OUT OF SHAPE | CHECK/REPLACE NEW BELT AND PULLEY KIT (P/N# 4589072) | |
HITACHI | VTF365AW | N/A | ABNORMAL GEAR NOISE DURING LOADING AND UNLOADING | CHECK/REPLACE WORM GEAR WITH NEW TYPE (P/N# 6816211) | |
HITACHI | VTF440 | N/A | INTERMITTENT EJECT DUE TO A DEFORMED FL CHANGE GEAR | CHECK/REPLACE WITH NEW PART # 6804834 | |
HITACHI | VTF440A | N/A | LOW OSD CHARACTER LEVELS WHEN USED IN A LOW TEMPERATURE AREA | CHANGE R1418 TO A 10k | |
HITACHI | VTF441 | N/A | INTERMITTENT EJECT DUE TO A DEFORMED FL CHANGE GEAR | CHECK/REPLACE WITH NEW PART # 6804834 | |
HITACHI | VTF445 | N/A | INTERMITTENT EJECT DUE TO A DEFORMED FL CHANGE GEAR | CHECK/REPLACE WITH NEW PART # 6804834 | |
HITACHI | VTF462A | N/A | RANDOM CHROMA BARS AT THE TOP OF THE SCREEN DURING PLAYBACK | CHANGE C227 TO A 0.0033uF (P/N# 0890038) | |
HITACHI | VTF462A | N/A | ABNORMAL GEAR NOISE DURING LOADING AND UNLOADING | CHECK/REPLACE WORM GEAR WITH NEW TYPE (P/N# 6816211) | |
HITACHI | VTF462A | N/A | ABNORMAL GEAR NOISE DURING LOADING AND UNLOADING | CHECK/REPLACE LOADING MOTOR WORM GEAR | |
HITACHI | VTF462A | N/A | CAPSTAN BELT SLIPS OFF AND BELT MAY BE WARPED OUT OF SHAPE | CHECK/REPLACE NEW BELT AND PULLEY KIT (P/N# 4589072) | |
HITACHI | VTF540 | N/A | WILL NOT ACCEPT A TAPE | CHECK/REPLACE R967 | |
HITACHI | VTF540 | N/A | DEAD | CHECK/REPLACE R852 (6.8 1/4w) | |
HITACHI | VTF540A | N/A | SLOW EJECT OR WON'T EJECT OR LAND TAPE | CHECK/REPLACE C1856 FOR LEAKAGE | |
HITACHI | VTF551A | N/A | VERTICAL JITTER - NOISY PICTURE AT TOP OR BOTTOM OF PICTURE | CHECK/REPLACE LOADING BLOCK ASSEMBLY (P/N# 7795471) LOADING POST NOT SEATING PROPERLY INTO THE 'V' CATCHER | |
HITACHI | VTF561AW | N/A | ABNORMAL GEAR NOISE DURING LOADING AND UNLOADING | CHECK/REPLACE WORM GEAR WITH NEW TYPE (P/N# 6816211) | |
HITACHI | VTF561AW | N/A | CAPSTAN BELT SLIPS OFF AND BELT MAY BE WARPED OUT OF SHAPE | CHECK/REPLACE NEW BELT AND PULLEY KIT (P/N# 4589072) | |
HITACHI | VTFX621A | N/A | DEAD - NO BLOWN FUSES - NO POWER | CHECK/REPLACE R853 (1meg? (P/N# 0700081) AND D859 (P/N# 5339241) OR A SUB OF ECG587 | |
HITACHI | VTFX623A | N/A | DEAD - NO BLOWN FUSES - NO POWER | CHECK/REPLACE R853 (1meg? (P/N# 0700081) AND D859 (P/N# 5339241) OR A SUB OF ECG587 | |
HITACHI | VTM110 | N/A | EXCESSIVE VERTICAL JITTER FROM THE ON-SCREEN DISPLAY WHEN VCR IS USED WITH A ZENITH TV | BRING UP SERVICE MENU ON TV (MENU,CHAN DOWN,VOL DOWN AT SAME TIME) - SWITCH V.FORCED MODE | |
HITACHI | VTM120 | N/A | DEAD | CHECK/REPLACE R852 (6.8 1/4w) | |
HITACHI | VTM120 | N/A | SLOW DRUM ROTATION | CHECK/REPLACE QF251 | |
HITACHI | VTM120 | N/A | INTERMITTENT EJECT DUE TO A DEFORMED FL CHANGE GEAR | CHECK/REPLACE WITH NEW PART # 6804834 | |
HITACHI | VTM120A | N/A | INCORRECT SERVO SPEED ON DRUM AND CAPSTAN | CHECK/REPLACE QF251 (MISSING 3.58mhz) | |
HITACHI | VTM121 | N/A | DEAD | CHECK/REPLACE R852 (6.8 1/4w) | |
HITACHI | VTM121 | N/A | INTERMITTENT EJECT DUE TO A DEFORMED FL CHANGE GEAR | CHECK/REPLACE WITH NEW PART # 6804834 | |
HITACHI | VTM121A | N/A | NO POWER OR DISPLAY | CHECK/REPLACE C880,D886,ZD754,R852 | |
HITACHI | VTM121A | N/A | NO POWER OR DISPLAY | CHECK/REPLACE IC753 (LOADING MOTOR DRIVE IC) | |
HITACHI | VTM123 | N/A | INTERMITTENT EJECT DUE TO A DEFORMED FL CHANGE GEAR | CHECK/REPLACE WITH NEW PART # 6804834 | |
HITACHI | VTM123 | N/A | DEAD | CHECK/REPLACE R852 (6.8 1/4w) | |
HITACHI | VTM131 | N/A | INTERMITTENT EJECT DUE TO A DEFORMED FL CHANGE GEAR | CHECK/REPLACE WITH NEW PART # 6804834 | |
HITACHI | VTM131 | N/A | EXCESSIVE VERTICAL JITTER FROM THE ON-SCREEN DISPLAY WHEN VCR IS USED WITH A ZENITH TV | BRING UP SERVICE MENU ON TV (MENU,CHAN DOWN,VOL DOWN AT SAME TIME) - SWITCH V.FORCED MODE | |
HITACHI | VTM131 | N/A | DEAD WITH NO DISPLAY - ALL POWER SUPPLY VOLTAGES CHECK OK | CHECK/REPLACE IC753 (BA6209) P/N# 5300795 | |
HITACHI | VTM132 | N/A | INTERMITTENT EJECT DUE TO A DEFORMED FL CHANGE GEAR | CHECK/REPLACE WITH NEW PART # 6804834 | |
HITACHI | VTM132 | N/A | EXCESSIVE VERTICAL JITTER FROM THE ON-SCREEN DISPLAY WHEN VCR IS USED WITH A ZENITH TV | BRING UP SERVICE MENU ON TV (MENU,CHAN DOWN,VOL DOWN AT SAME TIME) - SWITCH V.FORCED MODE | |
HITACHI | VTM132A | N/A | INTERMITTENTLY SHUTS OFF | CHECK/RESOLDER CONNECTIONS ON JUMPER W859 | |
HITACHI | VTM133 | N/A | INTERMITTENT EJECT DUE TO A DEFORMED FL CHANGE GEAR | CHECK/REPLACE WITH NEW PART # 6804834 | |
HITACHI | VTM135 | N/A | INTERMITTENT EJECT DUE TO A DEFORMED FL CHANGE GEAR | CHECK/REPLACE WITH NEW PART # 6804834 | |
HITACHI | VTM135A | N/A | BEAT INTERFERENCE IN THE E-E MODE ON CHANNEL 2 AND 4 - USUALLY DISAPPEARS AFTER 4-5 MINUTES | CHANGE R834 TO A 680 ohm | |
HITACHI | VTM137 | N/A | INTERMITTENT EJECT DUE TO A DEFORMED FL CHANGE GEAR | CHECK/REPLACE WITH NEW PART # 6804834 | |
HITACHI | VTM137A | N/A | DISTORTED VIDEO (CLIPPING) IN THE E-E MODE WHEN MONITORING THE VIDEO LINE OUTPUTS | CHECK/REPLACE IC801 | |
HITACHI | VTM140 | N/A | INTERMITTENT EJECT DUE TO A DEFORMED FL CHANGE GEAR | CHECK/REPLACE WITH NEW PART # 6804834 | |
HITACHI | VTM140 | N/A | DEAD WITH NO DISPLAY - ALL POWER SUPPLY VOLTAGES CHECK OK | CHECK/REPLACE IC753 (BA6209) P/N# 5300795 | |
HITACHI | VTM140 | N/A | EXCESSIVE VERTICAL JITTER FROM THE ON-SCREEN DISPLAY WHEN VCR IS USED WITH A ZENITH TV | BRING UP SERVICE MENU ON TV (MENU,CHAN DOWN,VOL DOWN AT SAME TIME) - SWITCH V.FORCED MODE | |
HITACHI | VTM141 | N/A | DEAD WITH NO DISPLAY - ALL POWER SUPPLY VOLTAGES CHECK OK | CHECK/REPLACE IC753 (BA6209) P/N# 5300795 | |
HITACHI | VTM141 | N/A | INTERMITTENT EJECT DUE TO A DEFORMED FL CHANGE GEAR | CHECK/REPLACE WITH NEW PART # 6804834 | |
HITACHI | VTM141 | N/A | EXCESSIVE VERTICAL JITTER FROM THE ON-SCREEN DISPLAY WHEN VCR IS USED WITH A ZENITH TV | BRING UP SERVICE MENU ON TV (MENU,CHAN DOWN,VOL DOWN AT SAME TIME) - SWITCH V.FORCED MODE | |
HITACHI | VTM141A | N/A | DISTORTED AND NOISY VIDEO IN PLAYBACK OF EP TAPES | CHECK/REPLACE VIDEO HEAD ASSY. | |
HITACHI | VTM150 | N/A | NO PLAYBACK AUDIO - TUNER AUDIO IS FINE - VIDEO OK ON BOTH | CHECK/REPLACE C406 | |
HITACHI | VTM150 | N/A | OSD SHAKES VERTICALLY AT HIGH TEMPERATURE | CHANGE C1445 TO A MYLAR TYPE (P/N 0880012) | |
HITACHI | VTM150 | N/A | LOW AUDIO OUTPUT ON SELF RECORDED TAPES | PERFORM ALIGNMENT OF AUDIO/CTRL HEAD - IF THIS DOESN'T CORRECT, THEN HEAD WILL NEED TO BE REPLACED | |
HITACHI | VTM151 | N/A | NO PLAYBACK AUDIO - TUNER AUDIO IS FINE - VIDEO OK ON BOTH | CHECK/REPLACE C406 | |
HITACHI | VTM151A | N/A | ERRATIC OPERATION OF THE INPUT KEYS,MAY GO TO A DIFFERENT MODE THAN WAS SELECTED | CHECK/REPLACE MODE SELECT SWITCH | |
HITACHI | VTM151A | N/A | BLUE BACKGROUND SHAKES WHEN CONNECTED TO SOME TV'S | CHECK/REPLACE IC1401 (P/N 1361445) | |
HITACHI | VTM151A | N/A | LOW OR NO RECORDED AUDIO IN PLAYBACK | CHECK ALIGNMENT OF AUDIO/CTRL HEAD - IF NO HELP,REPLACE | |
HITACHI | VTM170A | N/A | DISPLACED COLOR OR NO COLOR | CHECK FOR PROPER ADJUSTMENT OF 8.42 MHZ VCO LEVEL AT IC201 PIN 48 - ADJUST CP201 FOR 8.42 MHZ AND DC LEVEL IS 2.4VDC | |
HITACHI | VTM170A | N/A | NOT ACCEPTING TAPES OR SLOW TAKING TAPES - CAPSTAN MOTOR RUNS VERY SLOW | CHECK/REPLACE Q863 (ECG85) AND QF852 (600mA FUSE) | |
HITACHI | VTM170A | N/A | NO COLOR ON PLAYBACK OF A SELF RECORDED PREMIUM CHANNEL | CHECK/REPLACE IC201 (P/N# CP10171) MAY REQUIRE VIDEO CIRCUIT TO BE REALIGNED | |
HITACHI | VTM170A | N/A | NO COLOR WHEN PLAYING BACK A SELF RECORDING OF A PREMIUM CHANNEL | CHECK/REPLACE IC201 (P/N# HA118170ANT - 1345941) | |
HITACHI | VTM171A | N/A | DISPLACED COLOR OR NO COLOR | CHECK FOR PROPER ADJUSTMENT OF 8.42 MHZ VCO LEVEL AT IC201 PIN 48 - ADJUST CP201 FOR 8.42 MHZ AND DC LEVEL IS 2.4VDC | |
HITACHI | VTM171A | N/A | NO COLOR WHEN PLAYING BACK A SELF RECORDING OF A PREMIUM CHANNEL | CHECK/REPLACE IC201 (P/N# HA118170ANT - 1345941) | |
HITACHI | VTM171A | N/A | NOT ACCEPTING TAPES OR SLOW TAKING TAPES - CAPSTAN MOTOR RUNS VERY SLOW | CHECK/REPLACE Q863 (ECG85) AND QF852 (600mA FUSE) | |
HITACHI | VTM171A | N/A | NO COLOR ON PLAYBACK OF A SELF RECORDED PREMIUM CHANNEL | CHECK/REPLACE IC201 (P/N# CP10171) | |
HITACHI | VTM230 | N/A | VERTICAL JITTER ON SELF RECORDED EP TAPES | CHECK ALIGNMENT OF SUPPLY GUIDE POST - IF THIS DOESN'T CORRECT,THEN VCR WILL NEED VIDEO HEAD REPLACED | |
HITACHI | VTM231 | N/A | INTERMITTENT EJECT DUE TO A DEFORMED FL CHANGE GEAR | CHECK/REPLACE WITH NEW PART # 6804834 | |
HITACHI | VTM231 | N/A | EXCESSIVE VERTICAL JITTER FROM THE ON-SCREEN DISPLAY WHEN VCR IS USED WITH A ZENITH TV | BRING UP SERVICE MENU ON TV (MENU,CHAN DOWN,VOL DOWN AT SAME TIME) - SWITCH V.FORCED MODE | |
HITACHI | VTM231A | N/A | VERTICAL JITTER IN THE PLAYBACK OF EP RECORDINGS | CHECK/REPLACE VIDEO HEAD OR POST ALIGNMENT | |
HITACHI | VTM240 | N/A | INTERMITTENT EJECT DUE TO A DEFORMED FL CHANGE GEAR | CHECK/REPLACE WITH NEW PART # 6804834 | |
HITACHI | VTM240 | N/A | VERTICAL JITTER ON SELF RECORDED EP TAPES | CHECK ALIGNMENT OF SUPPLY GUIDE POST - IF THIS DOESN'T CORRECT,THEN VCR WILL NEED VIDEO HEAD REPLACED | |
HITACHI | VTM240 | N/A | EXCESSIVE VERTICAL JITTER FROM THE ON-SCREEN DISPLAY WHEN VCR IS USED WITH A ZENITH TV | BRING UP SERVICE MENU ON TV (MENU,CHAN DOWN,VOL DOWN AT SAME TIME) - SWITCH V.FORCED MODE | |
HITACHI | VTM240A | N/A | BLUE BACKGROUND FLASHES IN PLAYBACK WHEN THERE IS NO SIGNAL ON TAPE (SHOULD STAY BLUE) | CHECK/REPLACE HEAD AMPLIFIER ASSY. | |
HITACHI | VTM240A | N/A | DISTORTED AUDIO OF SELF-RECORDED TAPES | CHECK/REPLACE Q404 FOR LEAKAGE | |
HITACHI | VTM241 | N/A | EXCESSIVE VERTICAL JITTER FROM THE ON-SCREEN DISPLAY WHEN VCR IS USED WITH A ZENITH TV | BRING UP SERVICE MENU ON TV (MENU,CHAN DOWN,VOL DOWN AT SAME TIME) - SWITCH V.FORCED MODE | |
HITACHI | VTM241 | N/A | INTERMITTENT EJECT DUE TO A DEFORMED FL CHANGE GEAR | CHECK/REPLACE WITH NEW PART # 6804834 | |
HITACHI | VTM241A | N/A | INTERMITTENT EJECT | CHECK/REPLACE CLUTCH BASE ASSEMBLY | |
HITACHI | VTM250 | N/A | LOW AUDIO OUTPUT ON SELF RECORDED TAPES | PERFORM ALIGNMENT OF AUDIO/CTRL HEAD - IF THIS DOESN'T CORRECT, THEN HEAD WILL NEED TO BE REPLACED | |
HITACHI | VTM250 | N/A | DEAD WITH NO DISPLAY - ALL POWER SUPPLY VOLTAGES CHECK OK | CHECK/REPLACE IC753 (BA6209) P/N# 5300795 | |
HITACHI | VTM250A | N/A | BLUE BACKGROUND ALWAYS ON IN E-E AND PLAYBACK MODES | CHECK/REPLACE IC1401 | |
HITACHI | VTM250A | N/A | CAPSTAN MOTOR TURNS CONSTANTLY EVEN IN THE OFF MODE | CHECK/REPLACE CAPSTAN MOTOR | |
HITACHI | VTM250A | N/A | DISTORTED VIDEO AND WASHED OUT | CHECK/REPLACE CP203 OPEN | |
HITACHI | VTM250A | N/A | INDEX SEARCH SOMETIMES DOESN'T WORK PROPERLY | CHECK/REPLACE IC751 (P/N 1355831) | |
HITACHI | VTM250A | N/A | NO DISPLAY OR POWER UP | CHECK/REPLACE R708,IC753 OR CP751 | |
HITACHI | VTM251 | N/A | DEAD WITH NO DISPLAY - ALL POWER SUPPLY VOLTAGES CHECK OK | CHECK/REPLACE IC753 (BA6209) P/N# 5300795 | |
HITACHI | VTM260A | N/A | RANDOM CHROMA BARS AT THE TOP OF THE SCREEN DURING PLAYBACK | CHANGE R227 TO A 5.6k (P/N# 0700051) | |
HITACHI | VTM261AW | N/A | ABNORMAL GEAR NOISE DURING LOADING AND UNLOADING | CHECK/REPLACE WORM GEAR WITH NEW TYPE (P/N# 6816211) | |
HITACHI | VTM261AW | N/A | CAPSTAN BELT SLIPS OFF AND BELT MAY BE WARPED OUT OF SHAPE | CHECK/REPLACE NEW BELT AND PULLEY KIT (P/N# 4589072) | |
HITACHI | VTM262A | N/A | RANDOM CHROMA BARS AT THE TOP OF THE SCREEN DURING PLAYBACK | CHANGE R227 TO A 5.6k (P/N# 0700051) | |
HITACHI | VTM265A | N/A | DISPLACED COLOR OR NO COLOR | CHECK FOR PROPER ADJUSTMENT OF 8.42 MHZ VCO LEVEL AT IC201 PIN 48 - ADJUST CP201 FOR 8.42 MHZ AND DC LEVEL IS 2.4VDC | |
HITACHI | VTM265A | N/A | NO COLOR ON PLAYBACK OF A SELF RECORDED PREMIUM CHANNEL | CHECK/REPLACE IC201 (P/N# CP10171) | |
HITACHI | VTM265A | N/A | NOT ACCEPTING TAPES OR SLOW TAKING TAPES - CAPSTAN MOTOR RUNS VERY SLOW | CHECK/REPLACE Q863 (ECG85) AND QF852 (600mA FUSE) | |
HITACHI | VTM265A | N/A | NO COLOR WHEN PLAYING BACK A SELF RECORDING OF A PREMIUM CHANNEL | CHECK/REPLACE IC201 (P/N# HA118170ANT - 1345941) | |
HITACHI | VTM265A | N/A | QF852 BLOWS FOR NO APPARENT REASON | CHECK/REPLACE QF852 WITH NEW PART (P/N# 5721804 OR 5721942) | |
HITACHI | VTM270A | N/A | NO COLOR ON PLAYBACK OF A SELF RECORDED PREMIUM CHANNEL | CHECK/REPLACE IC201 (P/N# CP10171) | |
HITACHI | VTM270A | N/A | NOT ACCEPTING TAPES OR SLOW TAKING TAPES - CAPSTAN MOTOR RUNS VERY SLOW | CHECK/REPLACE Q863 (ECG85) AND QF852 (600mA FUSE) | |
HITACHI | VTM270A | N/A | DISPLACED COLOR OR NO COLOR | CHECK FOR PROPER ADJUSTMENT OF 8.42 MHZ VCO LEVEL AT IC201 PIN 48 - ADJUST CP201 FOR 8.42 MHZ AND DC LEVEL IS 2.4VDC | |
HITACHI | VTM270A | N/A | QF852 BLOWS FOR NO APPARENT REASON | CHECK/REPLACE QF852 WITH NEW PART (P/N# 5721804 OR 5721942) | |
HITACHI | VTM270A | N/A | NO COLOR WHEN PLAYING BACK A SELF RECORDING OF A PREMIUM CHANNEL | CHECK/REPLACE IC201 (P/N# HA118170ANT - 1345941) | |
HITACHI | VTM272A | N/A | DISPLACED COLOR OR NO COLOR | CHECK FOR PROPER ADJUSTMENT OF 8.42 MHZ VCO LEVEL AT IC201 PIN 48 - ADJUST CP201 FOR 8.42 MHZ AND DC LEVEL IS 2.4VDC | |
HITACHI | VTM272A | N/A | NOT ACCEPTING TAPES OR SLOW TAKING TAPES - CAPSTAN MOTOR RUNS VERY SLOW | CHECK/REPLACE Q863 (ECG85) AND QF852 (600mA FUSE) | |
HITACHI | VTM272A | N/A | QF852 BLOWS FOR NO APPARENT REASON | CHECK/REPLACE QF852 WITH NEW PART (P/N# 5721804 OR 5721942) | |
HITACHI | VTM272A | N/A | NO COLOR ON PLAYBACK OF A SELF RECORDED PREMIUM CHANNEL | CHECK/REPLACE IC201 (P/N# CP10171) | |
HITACHI | VTM272A | N/A | NO COLOR WHEN PLAYING BACK A SELF RECORDING OF A PREMIUM CHANNEL | CHECK/REPLACE IC201 (P/N# HA118170ANT - 1345941) | |
HITACHI | VTM290A | N/A | DEAD WITH MULTIPLE PARTS IN THE POWER SUPPLY BURNED CHECK/REPLACE R7,R8,R9 (27?483511057174), D9 ECG519 OR | 483513037048), IC01(483513087078), R12(0.82?@ 1w) D15 (483513037135), Q01 (483513047139), Q02 (483513047879) | |
HITACHI | VTMX221A | N/A | DEAD WITH MULTIPLE PARTS IN THE POWER SUPPLY BURNED CHECK/REPLACE D008 (ECG519 OR 483513037048) | IC001(483513087078), R014(0.91?@ 1w), R008 (82?@ 1w) D016 (483513037135), Q001(483513047139), Q002(483513047879) | |
HITACHI | VTS730A | N/A | HORZ. JITTER OF PIX IN PLAYBACK | CHECK/REPLACE IC1651 | |
HITACHI | VTS751A | N/A | POP NOISE AT THE END OF AUDIO/VIDEO DUBBING | ADD A 2.2uF @ 50v BETWEEN PIN 10 OF IC401 AND GROUND | |
JC PENNEY | 6865061 | N/A | VERT SYNC COMPRESSED OR DISTORTED-VERTICAL ROLL USUALLY ON LP AND SLP | CHANGE R619 >8.2k AND R620 >4.7k - ADD .047uF ACROSS R271 | |
JC PENNEY | 6865061 | N/A | RFI INTERFERENCE WHEN CONNECTED TO AC LINE | ADD 4.7uH(150702) IN SERIES FROM IC702 PIN 2 TO THE CATHODE OF D749-GROUND THE SHEILD OF THE DC-DC CONVERTOR | |
JC PENNEY | 6865067 | N/A | POWER SUPPLY BLOWS FUSES IMMEDIATELY-DIODES OK | CHECK C854 AND C860 SHORTED | |
JC PENNEY | 6865067 | N/A | NO DISPLAY-ALL OTHER FUNCTIONS ARE OK | CHECK C805,C807 AND DC-DC CONVERTER,IP801 | |
JC PENNEY | 6865067 | N/A | UNIT THINKS THAT A TAPE IS INSERTED | REPLACE BOTH TAPE END SENSORS | |
JC PENNEY | 6865067 | N/A | CAPSTAN MOTOR WILL NOT RUN | CHECK/REPLACE R631 FOR OPEN - ALSO INSPECT THE CAPSTAN FLYWHEEL BEARINGS FOR LUBRICATION | |
JC PENNEY | 6865067 | N/A | CAPSTAN SPEED IS OFF - TOO SLOW ON SP AND TOO FAST ON SLP | CHECK/REPLACE IC604 -CHECK PWM OUTPUT ON PIN#10 AND PIN#15 OF IC604 FOR PWM OUTPUT. | |
JC PENNEY | 6865067 | N/A | DRUM MOTOR WON'T START INTERMITTENTLY | CHECK FOR COLD SOLDER CONNECTIONS ON D617 AND D618 | |
JC PENNEY | 6865067 | N/A | INTERFERRENCE IN VIDEO-ESPECIALLY HIGH CHANNELS | APPEARS TO BE RADIATION--REPL.(2) 47uF @ 50 (DC-DC) | |
JC PENNEY | 6865067 | N/A | UNIT THINKS THAT A TAPE IS INSERTED | REPLACE BOTH TAPE END SENSORS | |
JC PENNEY | 6865067 | N/A | POWER SUPPLY BLOWS FUSES IMMEDIATELY-DIODES OK | CHECK C854 AND C860 SHORTED | |
JC PENNEY | 6865067 | N/A | AFTER EJECTING A TAPE, CARRIAGE WILL TRY TO LOAD AGAIN | CHECK/REPLACE Q142 TAKE-UP SENSOR (P/N# 161757) | |
JC PENNEY | 6865067 | N/A | NO DISPLAY | DC-DC CONVERTER BAD-REPL. (2) OPEN 47uF CAPACITORS | |
JC PENNEY | 6865071 | N/A | NO TRACKING CONTROL MAY LOCK IN BRIEFLY | CHECK/REPLACE IC2002 | |
JC PENNEY | 6865071 | N/A | PIX JITTERS ON SPECIAL EFFECTS | CHECK V-LOCK ADJUSTMENT-WORN HEADS-PG SHIFTERS TR.FIX | |
JC PENNEY | 6865071 | N/A | ALL MODES OPERATIONAL NO FIP DISPLAY | CHECK FILAMENT VOLT.MISSING CHECKPINS7&8 OF T1001 | |
JC PENNEY | 6865071 | N/A | WON'T POWER UP--DRUM RUNS CONTINUOUSLY | REPLACE IC6001 (MN15846VRG) | |
JC PENNEY | 6865071 | N/A | WEAK AUDIO (PLAYBACK ONLY) | CHECK C4014 | |
JC PENNEY | 6865071 | N/A | UNIT TICKS WHEN PLUGGED IN NO FIP | R1039 | |
JC PENNEY | 6865071 | N/A | WON'T RECORD -- MANUAL OR OTR | CLEAN OR REPLACE ERASE PROTECT SWITCH | |
JC PENNEY | 6865071 | N/A | VIDEO FROM RF VIDEO OUTLOOKS SCRAMBLED | CHECK VIDEO SIGNAL ON BOTH SIDES OF C3014 | |
JC PENNEY | 6865071 | N/A | POWERS UP-LOADS TAPE-NO PLAY,REC,EJECT,FF,REW | REPLACE IC7501 | |
JC PENNEY | 6865071 | N/A | FAILURE TO PASS LEAKAGE CURRENT HOT CHECK | CHECK OR REPLACE C1005 | |
JC PENNEY | 6865071 | N/A | POWER SUPPLY TICKS WHEN PLUGGED IN AND ALL SECONDARY VOLTAGES ARE LOW. | CHECK R1002 (680k) FOR OPEN | |
JC PENNEY | 6865071 | N/A | STARTS PLAYING THEN STOPS;COUNTER DOESN'T WORK | CHECK IC1551 | |
JC PENNEY | 6865071 | N/A | PUSH PLAY AND TAPE GOES TO REWIND | CHECK/REPLACE END SENSORS | |
JC PENNEY | 6865071 | N/A | WHEN PLAY IS PRESSED,VCR RUNS FOR 2-5 SECONDS THEN SHUTS OFF-NEVER SWITCHES FROM TUNER TO VCR-LOADING MOTOR RUNS ON | CHECK/REPLACE MODE SELECT SWITCH | |
JC PENNEY | 6865071 | N/A | SNOWY PIX IN PLAYBACK ONLY AUDIO OK | CHECK Q3001 | |
JC PENNEY | 6865071 | N/A | REDUCED CLOCK & DAY BRILLIANCE | CHECK R1215 | |
JC PENNEY | 6865071 | N/A | TRACKING ADJUSTMENTS | MOST ACCURATELY PERFORMED IN SP MODE. | |
JC PENNEY | 6865071 | N/A | CAPSTAN MOTOR OSCILLATES BACK & FORTH | REPLACE IC2002 | |
JC PENNEY | 6865071 | N/A | NO COLOR ON PLAYBACK OF PRE-RECORDED TAPES | CHECK/REPLACE IC8101 (MN6163) | |
JC PENNEY | 6865071 | N/A | TOP & BOTTOM 2' OF PIX. OK CENTER SNOWY | CHECK OR REPLACE IC8102 | |
JC PENNEY | 6865071 | N/A | INTERMITTENTLY STOPS PLAYING W/KNOWN GOOD TAPE | CHECK Q1552 (SUPPLY PHOTO XSTR) | |
JC PENNEY | 6865071 | N/A | NO COLOR IN PLAY BACK ONLY | REPLACE IC3502 ON THE HEAD AMP CBA | |
JC PENNEY | 6865071 | N/A | AFTER POWER IS APPLIED CAPSTAN SPINS FOR A FEW S | CHECK / REPLACE Q6003 IN MICROPROCESSOR CIRCUIT | |
JC PENNEY | 6865071 | N/A | SQUEL FROM THE POWER SUPP WHEN PLUGGED IN | CHECK D1023 | |
JC PENNEY | 6865071 | N/A | EXCESSIVE WOW AND FLUTTER | CHECK/REPLACE C2004 (BREAKING DOWN UNDER LOAD OR HIGH ESR) | |
JC PENNEY | 6865071 | N/A | NO COLOR | ADJUST VCO,VXO--CHECK 3.58MHZ,4.2MHZ,629KHZ | |
JC PENNEY | 6865071 | N/A | NO POWER UP--FIP OK,POWER SUPPLY OK | CK PIN #16 OF IC6001 (4-5V)--IF LOW,CK C6009 | |
JC PENNEY | 6865071 | N/A | GARBLED AUDIO IN LP AND SLP | CHECK PINCH ROLLER,CLUTCH ASSY.;IDLER | |
JC PENNEY | 6865071 | N/A | DEAD WITH OPEN FUSE | CHECK D1001,Q1001,R1003 | |
JC PENNEY | 6865071 | N/A | NO AUDIO | CHECK/REPLACE Q7010 & Q7002 | |
JC PENNEY | 6865071 | N/A | DISTORTION OF CASSETTE TRAY SIDE PLATE | CHECK R6070 RC00043,PLOO144,IC6001 | |
JC PENNEY | 6865071 | N/A | CAPSTAN MOTOR RUNS ABOUT 8SEC. THEN SHUTS DOWN | CHECK R6070 | |
JC PENNEY | 6865071 | N/A | WILL NOT RECORD WHEN TIMER IS SET | CHECK/CLEAN ERASE PROTECT SWITCH CONTACTS | |
JC PENNEY | 6865071 | N/A | AFTER POWER IS APPLIED CAPSTAN SPINS FORFEW SECS | CHECK/ REPLACE Q6003 IN MICROPROCESSOR CIRCUIT | |
JC PENNEY | 6865071 | N/A | NO AUTO STOP AT END OF TAPE IN PLAY FAST FOR REW | CHECK/REPLACE Q6008 | |
JC PENNEY | 6865071 | N/A | NO EE OR VV VIDEO AUDIO OK | CHECK/REPLACE IC3101 | |
JC PENNEY | 6866000 | N/A | SHUTDOWN AND WON'T EJECT TAPE - INTERMITTENT | CHECK/RESOLDER CONNECTIONS ON CAPSTAN MOTOR CONNECTOR OR | |
JC PENNEY | 6866006 | N/A | WILL NOT POWER UP-ALSO GOES TO REWIND WHEN PLUGGED IN | CHECK/REPLACE IC501 AND IC504 | |
JC PENNEY | 6866024 | N/A | EXCESSIVE WOW AND FLUTTER | CHANGE R234 TO A 180k AND R238 TO A 27k | |
JC PENNEY | 6866024 | N/A | WILL NOT RECORD A CONTROL TRACK ON TAPE - PRE-RECORDED TAPES WOULD PLAYBACK FINE ON ALL SPEEDS | CHECK/REPLACE IC201 (P/N# 668-156A) | |
JC PENNEY | 6866050 | N/A | WILL NOT POWER UP-ALSO GOES TO REWIND WHEN PLUGGED IN | CHECK/REPLACE IC501 AND IC504 | |
JC PENNEY | 6866051 | N/A | NO DRUM OR CAPSTAN OPERATION | CHECK D5A1 FOR OPEN | |
JC PENNEY | 6866051 | N/A | DEAD-BLOWING FUSES | CHECK D101,F101 | |
JC PENNEY | 6866051 | N/A | EXCESSIVE WOW AND FLUTTER | CHANGE R234 TO A 180k AND R238 TO A 27k | |
JC PENNEY | 6866051 | N/A | EXCESSIVE WOW AND FLUTTER | CHANGE R234 TO A 180k AND R238 TO A 27k | |
JC PENNEY | 6866051 | N/A | INTERMITTENT SNOWY PIX-LOOKS JUST LIKE A BAD HEAD OR DIRTY. | CHECK FOR COLD SOLDER JOINTS ON P3001 OF HEAD AMP | |
JC PENNEY | 6866051 | N/A | FM DEVIATION ADJUSTMENTS ARE TOO SENSITIVE | CHANGE R309 TO A 2.7k | |
JC PENNEY | 6866051 | N/A | INTERMITTENT SNOWY PIX-LOOKS JUST LIKE A BAD HEAD OR DIRTY. | CHECK FOR COLD SOLDER JOINTS OR NO SOLDER ON THE | |
JC PENNEY | 6866071 | N/A | RF RADIATION LINES IN PICTURE - GETS WORSE WHILE UNIT IS GOING INTO PLAY (WHEN MOTORS ARE RUNNING) BEFORE VCR MODE | CHECK/REPLACE C7,C9,C10,C14,C15,C16,C17,C18,C19,C23 | |
JC PENNEY | 6866074 | N/A | TUNES CHANNELS MANUALLY BUT WON'T HOLD CHANNEL MEMORY | CHECK/REPLACE IC7603 | |
JC PENNEY | 6866079 | N/A | DEAD WITH NO BLOWN FUSE OR REGULATOR TRANSISTOR | CHECK/REPLACE D1007 FOR SHORT (6.2V ZENER) | |
JC PENNEY | 6866079 | N/A | WOW & FLUTTER MOSTLY IN SLP SPEED | CHECK/REPLACE PINCH ROLLER | |
JC PENNEY | 6866079 | N/A | DD CYLINDER RUNS FOR ABOUT 1 MINUTE - CHANNEL NUMBERS CHANGE BUT RECEIVES ONLY SNOW | CHECK/REPLACE D1008 AND R1010 | |
JC PENNEY | 6866079 | N/A | NO CYLINDER OR CAPSTAN ACTION UNIT SHUTS DOWN | CHECK ICP-F38 (PR206)FOR OPEN CONDITION | |
JC PENNEY | 6866079 | N/A | ONE TICK FROM POWER SUPPLY-NO DISPLAY-NO POWER | CHECK PR1001,L1003,D1011,C1015 AND C1016 | |
JC PENNEY | 6866079 | N/A | PICTURE WOULD GO FROM GOOD TO SNOW-GOOD TO SNOW | CHECK/REPLACE C2023 | |
JC PENNEY | 6866079 | N/A | NO DISPLAY AND NO FUSES BLOWN | CHECK/REPLACE C1015 AND C1016 (330uF @ 16v) | |
JC PENNEY | 6866079 | N/A | PIX JITTERS ON SPECIAL EFFECTS | CHECK V-LOCK ADJUSTMENT-WORN HEADS-PG SHIFTERS TR.FIX | |
JC PENNEY | 6866079 | N/A | TRACKING PROBLEMS IN SP MODE AND 'DONALD DUCK' IN LP AND SLP MODES | CHECK/REPLACE C2023 FOR SHORT | |
JC PENNEY | 6866079 | N/A | NO FIP D1205 ON MAIN PWB BEING DRIVEN BEYOND TOL | CHECK C1018 FOR SHORTED CONDITION | |
JC PENNEY | 6866079 | N/A | FLOURESCENT DISPLAY VERY ERRATIC OR OUT COMPLETELY | CHECK/REPLACE C1004 | |
JC PENNEY | 6866079 | N/A | DRUM MOTOR WILL NOT RUN | CHECK/REPLACE IC2603 | |
JC PENNEY | 6866079 | N/A | POWER SUPPLY IS TICKING | CHECK D1007 FOR SHORT OR LEAKAGE | |
JC PENNEY | 6866079 | N/A | NO TUNER VIDEO BUT PLAYS A TAPE OK | CHECK/REPLACE L708,R721 AND C723 | |
JC PENNEY | 6866079 | N/A | SNOW TO NORMAL PIX ON SELF RECORDED TAPES | CHECK CONNECTIONS ON IC2001 (ESPEC. PIN #2) | |
JC PENNEY | 6866079 | N/A | DEAD SET AND SHORT ON THE 5 VOLT LINE | CHECK/REPLACE C3137 AND PR1001 | |
JC PENNEY | 6866079 | N/A | NO COLOR | ADJUST VCO,VXO--CHECK 3.58MHZ,4.2MHZ,629KHZ | |
JC PENNEY | 6866079 | N/A | WHEN UNIT IS PLUGGED IN,CAPSTAN RUNS 4-5 SECONDS AND SHUTS DOWN. | CHECK/REPLACE D1008 AND R1010 | |
JC PENNEY | 6866079 | N/A | AFTER UNIT RUNS FOR 1/2 TO 1 HOUR, DISPLAY GOES OUT AND VCR LOCKS UP - WON'T TAKE ANY COMMANDS | CHECK/REPLACE IC7502 (MN1280-R) RESET IC | |
JC PENNEY | 6866079 | N/A | SUPPLY REELS START TURNING AS SOON AS UNIT IS PLUGGED IN BUT WILL NOT STAY ON - WILL NOT LOAD CASSETTE | CHECK/REPLACE R1010,D1008 AND C1011 | |
JC PENNEY | 6866079 | N/A | TRACKING ADJUSTMENTS | MOST ACCURATELY PERFORMED IN SP MODE. | |
JC PENNEY | 6866079 | N/A | CAPSTAN SPINS THEN POWER SHUTS OFF (AT POWER UP) | CHECK IC6001 AND IC6002 | |
JC PENNEY | 6866079 | N/A | CAPSTAN MOTOR FLIP FLOPS BACK AND FORTH | CHECK IC8101 | |
JC PENNEY | 6866079 | N/A | INTERMITTENT LOW NO AUDIO IN E/E PLAYBACK AUD,OK | REPLACE IC4001 | |
JC PENNEY | 6866079 | N/A | GARBLED AUDIO-TUNER AUDIO NOT SWITCHING ON P.B. | REPLACE IC4001 | |
JC PENNEY | 6866079 | N/A | WON'T RECORD -- MANUAL OR OTR | CLEAN OR REPLACE ERASE PROTECT SWITCH | |
JC PENNEY | 6866079 | N/A | TV/VCR FUNCTIONS DOESN'T WORK BUT INDICATOR DOES LIGHT IN THE FIP DISPLAY | CHECK/REPLACE IC7601 | |
JC PENNEY | 6866079 | N/A | GARBLED AUDIO IN LP AND SLP | CHECK PINCH ROLLER,CLUTCH ASSY.;IDLER | |
JC PENNEY | 6866079 | N/A | SUPPLY REEL STARTS TURNING WHEN UNIT IS PLUGGED | CHECK/REPLACE R1010 D1008 C1011 | |
JC PENNEY | 6866079 | N/A | CAPSTAN SPINS A FEW TIMES THEN UNIT SHUTS DOWN | CHECK /REPLACE R1010 Q606 | |
JC PENNEY | 6866568 | N/A | NO SPEED CONTROL - RUNAWAY ON PLAY | CHECK/REPLACE C247 AND C248 | |
JC PENNEY | 6866568 | N/A | WILL NOT ACCEPT TAPE | CHECK IC602 | |
JC PENNEY | 6866568 | N/A | 1 KHz TONE IN AUDIO ON PLAYBACK | CHECK/REPLACE R401 OR OPEN GROUND TO THE GROUND SIDE OF | |
JC PENNEY | 6866569 | N/A | WILL NOT POWER UP-ALSO GOES TO REWIND WHEN PLUGGED IN | CHECK/REPLACE IC501 AND IC504 | |
JC PENNEY | 6866569 | N/A | TRACKING PROBLEMS - PIX/SNOW/PIX/SNOW | CHECK FOR COLD SOLDER CONNECTIONS ON PLUG P2D03 | |
JC PENNEY | 6866569 | N/A | ERRATIC CAPSTAN OPERATION | CHECK/RESOLDER CONNECTIONS ON PLUG P2D01,P2D02 AND P2D03 | |
JC PENNEY | 6866569 | N/A | TRACKING WILL NOT ADJUST | CHECK/REPLACE IC201 | |
JC PENNEY | 6866569 | N/A | COUNTER WILL NOT COUNT | MODIFY PER SERVICE BULLETIN FOR GHV-1240M (MANUAL) | |
JC PENNEY | 8558298 | N/A | EXCESSIVE WOW AND FLUTTER | CHANGE R234 TO A 180k AND R238 TO A 27k | |
JC PENNEY | 8558298 | N/A | WILL NOT RECORD A CONTROL TRACK ON TAPE - PRE-RECORDED TAPES WOULD PLAYBACK FINE ON ALL SPEEDS | CHECK/REPLACE IC201 (P/N# 668-156A) | |
JC PENNEY | 8558447 | N/A | ERRATIC TAPE COUNTER OPERATION | CHANGE R517 TO 27k | |
JC PENNEY | 8558447 | N/A | MANY VERTICAL BARS ON THE SCREEN THAT FLASH ON AND OFF IF THE CLOCK HASN'T BEEN SET. | CHECK/REPLACE IC801 | |
JC PENNEY | 8558447 | N/A | WON'T LOAD A TAPE | CHECK/REPLACE LOADING BRACKET ASSY. (P/N# 321-223A) | |
JC PENNEY | 8558538 | N/A | OSD TITLES ARE TOO DIM | CHANGE R864 TO A 8.2k | |
JC PENNEY | 8558538 | N/A | PICTURE DISTORTION DURING TITLE MODE (THE AUDIO OSC. INTERFERES W/THE VIDEO SIGNAL DURING REC) | REMOVE C871 FROM CIRCUIT | |
JC PENNEY | 8558538 | N/A | WON'T RECORD AUDIO OR ERASE OLD AUDIO | CHECK/REPLACE R427 FOR OPEN (47k) | |
JC PENNEY | 8558538 | N/A | AUDIO DISTORTION | CHANGE R708 TO 390 ohm - R709 TO 820 ohm - C709 TO 27pf | |
JC PENNEY | 8558595 | N/A | NOISE IN PICTURE FROM MOTOR DRIVER IC | CHANGE C556 TO A 10uF @ 16v ALSO CHECK IC201 FOR DAMAGE | |
JC PENNEY | 8558595 | N/A | POOR PICTURE LOCK IN THE PLAYBACK MODE | ADD A 47uF @ 16v FROM PIN 25 OF IC201 TO GRD. AND ADD 1k | |
JC PENNEY | 8558595 | N/A | UNSTABLE COLOR | CHANGE R323 TO 100k AND C340 TO .22uF | |
JC PENNEY | 8558595 | N/A | EXCESSIVE WOW AND FLUTTER BEYOND TOLERANCES | CHANGE R211 TO 27k AND R208 TO 120k | |
JVC | BR9050U | N/A | NO DISPLAY AND NO FUNCTIONS | CHECK/REPLACE C3 (TIMER BACKUP BOARD) FOR SHORT | |
JVC | BRS411U | N/A | NO FM AUDIO IN PLAYBACK OR RECORD MODE | CHECK/REPLACE C154 (P/N# QER40GM-227) | |
JVC | BRS411U | N/A | LUMINANCE LEVEL IS VERY HIGH IN RECORD AND E-E MODES | CHECK/REPLACE C14 (AGC DETECTOR CAPACITOR) | |
JVC | BRS411U | N/A | CAPSTAN RUNS CONTINUOUSLY | CHECK/REPLACE Q9 (2SA1282AF) ON SERVO PCB | |
JVC | BRS522U | N/A | POOR VIDEO WHEN USING THE SA-N22W | CHECK/RESOLDER CONNECTIONS ON KA303 ON THE TBC-1 BOARD | |
JVC | BRS525U | N/A | VERTICAL PICTURE JITTER AFTER WARM-UP IN THE TBC MODE | CHECK/REPLACE IC106 (P/N# TC74HC74AF) | |
JVC | BRS605U | N/A | NO E-E AUDIO BUT PLAYBACK AUDIO IS FINE | CHECK/REPLACE Q1 (P/N# 2SD973AR) ON MECHACON CIRCUIT BD. | |
JVC | BRS622U | N/A | SYNC PULSES IN VIDEO SIGNAL COLLAPSES | CHECK/REPLACE IC21 IN Y COMB CIRCUIT (P/N# JCP0009) | |
JVC | BRS622U | N/A | VHS PLAYBACK ONLY - WILL NOT PLAYBACK S-VHS | CHECK/REPLACE LPF3 (P/N# PELN0336-01-01) IN THE R/P 'Y' CIRCUIT | |
JVC | BRS622U | N/A | WILL NOT RECORD COLOR WHEN UNIT IS COLD | CHECK FOR THE PROPER POLARITY OF C168 AT PIN 9 OF IC22 | |
JVC | BRS822U | N/A | WILL NOT RECORD COLOR WHEN UNIT IS COLD | CHECK FOR THE PROPER POLARITY OF C168 AT PIN 9 OF IC22 | |
JVC | GFS550U | N/A | PICTURE DARK AND DISTORTED | CHECK/REPLACE IC3 ON THE VIDEO-2 BOARD (YB20005B) | |
JVC | GRAX75U | N/A | LENS DOES NOT FOCUS - WHILE ZOOMING IN,IRIS CLOSES, WHILE ZOOMING OUT, IRIS OPENS | CHECK/RESOLDER CONNECTIONS ON CN202 ON CAMERA PCB | |
JVC | HR670U | N/A | TRIES TO LOAD TAPE IMMEDIATELY WHEN POWER IS TURNED ON | CHECK/REPLACE CP601 FOR OPEN | |
JVC | HRA21U | N/A | LOAD POST JAMS INTERMITTENTLY | CHECK/REPLACE LOAD POST (P/N# PQ46330A-3), TENSION ARM (PQ35012),LOADING ARM (PQ46337A-3), PLATE (PQ11658-1-15) | |
JVC | HRA21U | N/A | DRUM MOTOR RUNS IN ALL MODES | CHECK/REPLACE STATOR ASSY. (P/N# PDZ0141-1-2) | |
JVC | HRA21U | N/A | WHEN GOING INTO PLAY MODE, THEN TENSION ARM JAMS | CHECK/REPLACE TENSION ARM LEVER (P/N# PQ35012) | |
JVC | HRA33 | N/A | POWER TURNS ON THEN SHUTS BACK OFF - WHEN ANY MOTOR TRIES TO RUN, POWER SHUTS OFF | CHECK/REPLACE C902 (47uF @ 200v) | |
JVC | HRA41U | N/A | LOAD POST JAMS INTERMITTENTLY | CHECK/REPLACE LOAD POST (P/N# PQ46330A-3), TENSION ARM (PQ35012),LOADING ARM (PQ46337A-3), PLATE (PQ11658-1-15) | |
JVC | HRA41U | N/A | EATS TAPES - WON'T REWIND | CHECK FOR A BENT SUPPLY OR TAKE-UP REEL SHAFT AND REEL TABLE OUT OF ALIGNMENT | |
JVC | HRA53U | N/A | UNIT LOADS A TAPE THEN FREEZES - SOMETIMES HAS A BLUE SCREEN WITH ARROWS POINTING TO THE LEFT | CHECK/REPLACE IC1201 (P/N# UPD16312GB(P) ) | |
JVC | HRA61U | N/A | EATS TAPES - WON'T REWIND | CHECK FOR A BENT SUPPLY OR TAKE-UP REEL SHAFT AND REEL TABLE OUT OF ALIGNMENT | |
JVC | HRA61U | N/A | TAPE MECHANISM JAMMED - GUIDE ARM STUCK ON CONTROL ARM | CHECK/REPLACE TORSION SPRING (P/N# PQ4632-1-2) | |
JVC | HRA61U | N/A | LOAD POST JAMS INTERMITTENTLY | CHECK/REPLACE LOAD POST (P/N# PQ46330A-3), TENSION ARM (PQ35012),LOADING ARM (PQ46337A-3), PLATE (PQ11658-1-15) | |
JVC | HRA61U | N/A | PICTURE HAS HORZ. LINES ON PLAYBACK OF TAPES | CHECK/REPLACE IC401 (P/N# BU2882S) | |
JVC | HRA61U | N/A | TAPE JAMS IN MECHANISM | CHECK/REPLACE PINCH ROLLER ARM ASSY. (P/N# PQ46327A) | |
JVC | HRD151U | N/A | CAPSTAN MOTOR WILL NOT RUN | CHECK/REPLACE CP1 FOR OPEN ( ON REGULATOR BOARD) | |
JVC | HRD180U | N/A | POWER BUTTON DOESN'T WORK-DRUM WILL NOT RUN | REPLACE STK5481 IC | |
JVC | HRD180U | N/A | QUIVVER IN SLP AUDIO - SP AND LP ARE NORMAL | CHECK/REPLACE IC403 | |
JVC | HRD3050U | N/A | REEL MOTOR RUNS FOR 5-10 SECONDS THEN POWER GOES OFF | CHECK/REPLACE IC602 AND IC604 | |
JVC | HRD3050U | N/A | REEL MOTOR RUNS FOR 5-10 SECONDS THEN POWER GOES OFF | CHECK/REPLACE IC602 AND IC604 | |
JVC | HRD3050U | N/A | NO POWER LED - SHOWS THAT A TAPE IS PRESENT WHEN NO TAPE IS INSERTED. +5 OR +12 VOLTS MISSING | CHECK/REPLACE REGULATOR IC (STK5474) | |
JVC | HRD3050U | N/A | WHEN POWER IS TURNED ON, CASSETTE HOUSING TRIES TO LOAD A TAPE WITH NONE INSERTED AND THEN SHUTS OFF. | CHECK/REPLACE PHS3 PHOTO SENSOR (P/N# PU60629) | |
JVC | HRD3050U | N/A | DRUM MOTOR WILL NOT RUN | CHECK/REPLACE IC601 (TP602 DRUM ON SHOULD BE HIGH WHEN IN PLAY) | |
JVC | HRD3050U | N/A | NO POWER LED - SHOWS THAT A TAPE IS PRESENT WHEN NO TAPE IS INSERTED. +5 OR +12 VOLTS MISSING | CHECK/REPLACE REGULATOR IC (STK5479) | |
JVC | HRD310U | N/A | HORIZONTAL LINES IN THE PICTURE ON PLAYBACK AND AUDIO IS VERY SLOW. | CHECK/REPLACE IC201 ON THE SERVO PWB (PU22517A-02) | |
JVC | HRD4050U | N/A | WHEN POWER IS TURNED ON, CASSETTE HOUSING TRIES TO LOAD A TAPE WITH NONE INSERTED AND THEN SHUTS OFF. | CHECK/REPLACE PHS3 PHOTO SENSOR (P/N# PU60629) | |
JVC | HRD4050U | N/A | EATS TAPES WHEN PRESSING REVIEW | CLEAN OR REPLACE MODE SELECT SWITCH | |
JVC | HRD4050U | N/A | INTERMITTENT GOES TO BLUE SCREEN - INTERMITTENT AUDIO MUTE | CHECK/RESOLDER CONNECTIONS ON CRYSTAL INSIDE TUNER PRESCALER SECTION | |
JVC | HRD5050U | N/A | AFTER SEVERAL RECORDINGS AND THEN USING THE INDEX FEATURE, THE UNIT WOULD GO INTO THE FF MODE WHILE PLAYING. | CHECK/REPLACE IC601 | |
JVC | HRD5050U | N/A | INTERMITTENT GOES TO BLUE SCREEN - INTERMITTENT AUDIO MUTE | CHECK/RESOLDER CONNECTIONS ON CRYSTAL INSIDE TUNER PRESCALER SECTION | |
JVC | HRD515U | N/A | INTERMITTENT GOES TO BLUE SCREEN - INTERMITTENT AUDIO MUTE | CHECK/RESOLDER CONNECTIONS ON CRYSTAL INSIDE TUNER PRESCALER SECTION | |
JVC | HRD515U | N/A | NO TUNER VIDEO | CHECK/REPLACE Q801 (2SB810H) ON MAIN BOARD | |
JVC | HRD520U | N/A | INTERMITTENT GOES TO BLUE SCREEN - INTERMITTENT AUDIO MUTE | CHECK/RESOLDER CONNECTIONS ON CRYSTAL INSIDE TUNER PRESCALER SECTION | |
JVC | HRD520U | N/A | WHEN POWER IS TURNED ON, CASSETTE HOUSING TRIES TO LOAD A TAPE WITH NONE INSERTED AND THEN SHUTS OFF. | CHECK/REPLACE PHS3 PHOTO SENSOR (P/N# PU60629) | |
JVC | HRD530U | N/A | NO VIDEO IN PLAYBACK MODE - MAY HAVE OSD AND CLOCK | CHECK/REPLACE Q1 (P/N# 2SC1317(R,S) ) ON TIMER CBA | |
JVC | HRD540U | N/A | WHEN POWER IS TURNED ON, CASSETTE HOUSING TRIES TO LOAD A TAPE WITH NONE INSERTED AND THEN SHUTS OFF. | CHECK/REPLACE PHS3 PHOTO SENSOR (P/N# PU60629) | |
JVC | HRD540U | N/A | VCR SQUEALS FOR A MOMENT WHEN PLUGGED IN, OTHERWISE DEAD | CHECK/REPLACE Q2 (2SC3616(MLK)-T) AND D22 (RD15ES-T1B1) | |
JVC | HRD550U | N/A | WHEN POWER IS TURNED ON, CASSETTE HOUSING TRIES TO LOAD A TAPE WITH NONE INSERTED AND THEN SHUTS OFF. | CHECK/REPLACE PHS3 PHOTO SENSOR (P/N# PU60629) | |
JVC | HRD600U | N/A | ERRATIC OPERATION - EATS TAPES INTERMITTENTLY, POSSIBLY WHEN GOING FROM PLAY TO STOP OR EJECT MODE | CLEAN OR REPLACE MODE SELECT SWITCH | |
JVC | HRD600U | N/A | INTERMITTENT GOES TO BLUE SCREEN - INTERMITTENT AUDIO MUTE | CHECK/RESOLDER CONNECTIONS ON CRYSTAL INSIDE TUNER PRESCALER SECTION | |
JVC | HRD600U | N/A | NO DISPLAY UNIT WILL OPERATES OTHERWISE | CHECK/REPLACE R21 (47? | |
JVC | HRD600U | N/A | WHEN POWER IS TURNED ON, CASSETTE HOUSING TRIES TO LOAD A TAPE WITH NONE INSERTED AND THEN SHUTS OFF. | CHECK/REPLACE PHS3 PHOTO SENSOR (P/N# PU60629) | |
JVC | HRD600U | N/A | DEAD - POWER SUPPLY CHIRPS OR SQUEALS | CHECK/REPLACE C9,C18,C21 AND C33 | |
JVC | HRD610U | N/A | ERRATIC OPERATION - EATS TAPES INTERMITTENTLY, POSSIBLY WHEN GOING FROM PLAY TO STOP OR EJECT MODE | CLEAN OR REPLACE MODE SELECT SWITCH | |
JVC | HRD610U | N/A | WILL NOT TUNE-ONLY SNOW-MAY BE THERMAL | CHECK/REPLACE IC1 (M51366SP) ON TUNING BOARD | |
JVC | HRD610U | N/A | INTERMITTENT GOES TO BLUE SCREEN - INTERMITTENT AUDIO MUTE | CHECK/RESOLDER CONNECTIONS ON CRYSTAL INSIDE TUNER PRESCALER SECTION | |
JVC | HRD610U | N/A | WILL NOT RECORD COLOR | CHECK/REPLACE BPF201 (PU57399-3S) | |
JVC | HRD610U | N/A | WILL NOT TUNE CHANNELS | CHECK/REPLACE R20 (P/N# 863-6525) | |
JVC | HRD610U | N/A | WHEN POWER IS TURNED ON, CASSETTE HOUSING TRIES TO LOAD A TAPE WITH NONE INSERTED AND THEN SHUTS OFF. | CHECK/REPLACE PHS3 PHOTO SENSOR (P/N# PU60629) | |
JVC | HRD610U | N/A | PRESS PLAY,VCR MAY SHOW A NORMAL PICTURE,HALF PICTURE AND HALF SNOW OR ALL SNOW. PRESS STOP THEN PLAY, MAY WORK FINE. | CHECK/REPLACE LOWER DRUM OR STATOR UNIT ON DRUM MOTOR | |
JVC | HRD620U | N/A | WHEN POWER IS TURNED ON, CASSETTE HOUSING TRIES TO LOAD A TAPE WITH NONE INSERTED AND THEN SHUTS OFF. | CHECK/REPLACE PHS3 PHOTO SENSOR (P/N# PU60629) | |
JVC | HRD620U | N/A | INTERMITTENT GOES TO BLUE SCREEN - INTERMITTENT AUDIO MUTE | CHECK/RESOLDER CONNECTIONS ON CRYSTAL INSIDE TUNER PRESCALER SECTION | |
JVC | HRD660U | N/A | ERASES VIDEO DURING PLAYBACK | CHECK/REPLACE IC601 (M37418M6-216SP) | |
JVC | HRD660U | N/A | INTERMITTENTLY EATS TAPES ON REWIND AND FAST FORWARD SEARCH MODES | CHECK/REPLACE SMALL WHITE NYLON GEAR ON CAPSTAN MOTOR FOR CRACKS (P/N 61003-1-2) | |
JVC | HRD660U | N/A | WHEN POWER IS TURNED ON, CASSETTE HOUSING TRIES TO LOAD A TAPE WITH NONE INSERTED AND THEN SHUTS OFF. | CHECK/REPLACE PHS3 PHOTO SENSOR (P/N# PU60629) | |
JVC | HRD670U | N/A | STOPS INTERMITTENTLY - PRESS PLAY AND IT WILL RUN FOR A SHORT TIME THEN STOP AGAIN - COUNTER WORKS NORMAL | CHECK/REPLACE PHS1 AND PHS2 (TAKE-UP/SUPPLY REEL SENSORS) | |
JVC | HRD670U | N/A | WHEN POWER IS TURNED ON, CASSETTE HOUSING TRIES TO LOAD A TAPE WITH NONE INSERTED AND THEN SHUTS OFF. | CHECK/REPLACE PHS3 PHOTO SENSOR (P/N# PU60629) | |
JVC | HRD720U | N/A | ONLY TUNES CHANNEL 2 | CHECK/REPLACE IC702 (P/N# 93C46/P) ON THE TIMER/DISPLAY BD. | |
JVC | HRD730U | N/A | WHEN POWER IS TURNED ON, CASSETTE HOUSING TRIES TO LOAD A TAPE WITH NONE INSERTED AND THEN SHUTS OFF. | CHECK/REPLACE PHS3 PHOTO SENSOR (P/N# PU60629) | |
JVC | HRD730U | N/A | DRUM, CAPSTAN AND REEL MOTOR TURNS ERRATICALLY WHEN UNIT IS PLUGGED IN | CHECK/REPLACE Q9 ON SWITCHING REG. BOARD (P/N# 2SB1068(KU)) | |
JVC | HRD740U | N/A | NO FUNCTIONS | CHECK/REPLACE Q9 (P/N# 2SB1068(UK)) ON REGULATOR BOARD | |
JVC | HRD740U | N/A | DRUM, CAPSTAN AND REEL MOTOR TURNS ERRATICALLY WHEN UNIT IS PLUGGED IN | CHECK/REPLACE Q9 ON SWITCHING REG. BOARD (P/N# 2SB1068(KU)) | |
JVC | HRD740U | N/A | EACH TIME THE UNIT IS PUT INTO PLAY, A BAND OF SNOW APPEARS IN DIFFERENT PLACES ON THE SCREEN | CHECK/REPLACE C6 (3.3uF @ 50v P/N# ECEV1HV3R3R) ON DRUM AND/OR IC1 (P/N# VC5032) | |
JVC | HRD740U | N/A | WILL NOT AUTO-TUNE | CHECK/REPLACE IC601 (M37524M4-103SP) ON MAIN BOARD | |
JVC | HRD740U | N/A | WHEN POWER IS TURNED ON, CASSETTE HOUSING TRIES TO LOAD A TAPE WITH NONE INSERTED AND THEN SHUTS OFF. | CHECK/REPLACE PHS3 PHOTO SENSOR (P/N# PU60629) | |
JVC | HRD830U | N/A | NO RECORD,PLAYBACK,FF OR REW | CHECK/REPLACE F2 AND THE CAPSTAN MOTOR (PU60892) | |
JVC | HRD830U | N/A | WHEN THE UNIT IS POWERED UP,CARRIAGE TRIES TO LOAD WITHOUT A CASSETTE. | CHECK/REPLACE F3 FUSE ON POWER XFRM. PWB | |
JVC | HRD830U | N/A | NO COLOR DURING PLAYBACK | CHECK/REPLACE BPF201 (PU60631),T201 (PU60057-3),IC201 (PU22517C) | |
JVC | HRD830U | N/A | NO PICTURE - NO HI-FI AUDIO - DRUM AND CAPSTAN SPIN SLOWLY | CHECK/REPLACE CF201 (PU58852) CERAMIC FILTER | |
JVC | HRD830U | N/A | CANNOT ADJUST HEAD SWITCHING POINT | CHECK/REPLACE C6 (P/N# ECEV1HV3R3R) ON DRUM MOTOR BOARD | |
JVC | HRD830U | N/A | WHEN POWER IS TURNED ON, CASSETTE HOUSING TRIES TO LOAD A TAPE WITH NONE INSERTED AND THEN SHUTS OFF. | CHECK/REPLACE PHS3 PHOTO SENSOR (P/N# PU60629) | |
JVC | HRD830U | N/A | PLAYBACK PICTURE IS DARK - SOUND IS NORMAL | CHECK/REPLACE EQ1 (VIDEO PCB --P/N PU60056-2) | |
JVC | HRD840U | N/A | NO RECORD,PLAYBACK,F/F OR REW | CHECK/REPLACE PLATE ASSEMBLY (PQ43555B) | |
JVC | HRD840U | N/A | WHEN POWER IS TURNED ON, CASSETTE HOUSING TRIES TO LOAD A TAPE WITH NONE INSERTED AND THEN SHUTS OFF. | CHECK/REPLACE PHS3 PHOTO SENSOR (P/N# PU60629) | |
JVC | HRD850U | N/A | NO TUNER OPERATION | CHECK/REPLACE IC2 (DIGITAL/ANALOG BOARD) P/N BA7603F | |
JVC | HRD850U | N/A | WHEN POWER IS TURNED ON, CASSETTE HOUSING TRIES TO LOAD A TAPE WITH NONE INSERTED AND THEN SHUTS OFF. | CHECK/REPLACE PHS3 PHOTO SENSOR (P/N# PU60629) | |
JVC | HRD860U | N/A | WHEN POWER IS TURNED ON, CASSETTE HOUSING TRIES TO LOAD A TAPE WITH NONE INSERTED AND THEN SHUTS OFF. | CHECK/REPLACE PHS3 PHOTO SENSOR (P/N# PU60629) | |
JVC | HRD860U | N/A | INTERMITTENTLY WON'T TRACK AND HI-FI DROPS OUT | CHECK/REPLACE LOADING ARM ASSY. (P/N# PQ43542D-4) | |
JVC | HRD865U | N/A | DEAD - POWER SUPPLY CHIRPS OR SQUEALS | CHECK/REPLACE C9,C18,C21 AND C33 | |
JVC | HRD865U | N/A | WHEN POWER IS TURNED ON, CASSETTE HOUSING TRIES TO LOAD A TAPE WITH NONE INSERTED AND THEN SHUTS OFF. | CHECK/REPLACE PHS3 PHOTO SENSOR (P/N# PU60629) | |
JVC | HRD865U | N/A | EACH TIME THE UNIT IS PUT INTO PLAY, A BAND OF SNOW APPEARS IN DIFFERENT PLACES ON THE SCREEN | CHECK/REPLACE C6 (3.3uF @ 50v P/N# ECEV1HV3R3R) ON DRUM AND/OR IC1 (P/N# VC5032) | |
JVC | HRD870U | N/A | WHEN POWER IS TURNED ON, CASSETTE HOUSING TRIES TO LOAD A TAPE WITH NONE INSERTED AND THEN SHUTS OFF. | CHECK/REPLACE PHS3 PHOTO SENSOR (P/N# PU60629) | |
JVC | HRD870U | N/A | UNIT GOES INTO RECORD MODE BUT RECORDS AUDIO AND VIDEO INTERMITTENTLY | CHECK/REPLACE IC2 (P/N# SN74HCU04N) ON AUDIO BOARD | |
JVC | HRD870U | N/A | INTERMITTENT POWER ON AND HAS A SIZZLE SOUND | CHECK/REPLACE C33 (P/N# QEZ0156-127Z) AND C34 (P/N# QETC0JM-107) | |
JVC | HRD870U | N/A | EACH TIME THE UNIT IS PUT INTO PLAY, A BAND OF SNOW APPEARS IN DIFFERENT PLACES ON THE SCREEN | CHECK/REPLACE C6 (3.3uF @ 50v P/N# ECEV1HV3R3R) ON DRUM AND/OR IC1 (P/N# VC5032) | |
JVC | HRD870U | N/A | NO DISPLAY UNIT WILL OPERATES OTHERWISE | CHECK/REPLACE R21 (47? | |
JVC | HRD870U | N/A | DEAD SET - NO DISPLAY - DISCONNECTING DISPLAY HEATER, UNIT WILL OPERATE | CHECK/REPLACE C33 IN POWER SUPPLY CIRCUIT (120uF @ 6.3v) | |
JVC | HRD870U | N/A | NO AUDIO | CHECK/REPLACE IC601 (M37418M6-244SP) | |
JVC | HRD875U | N/A | AFTER LOADING, THE UNIT WILL NOT RESPOND, IT ONLY RUNS IN THE REVERSE DIRECTION | CHECK/REPLACE Q5 (P/N# 2SD1468S(RS)-T ) ON REGULATOR BOARD | |
JVC | HRD875U | N/A | WHEN POWER IS TURNED ON, CASSETTE HOUSING TRIES TO LOAD A TAPE WITH NONE INSERTED AND THEN SHUTS OFF. | CHECK/REPLACE PHS3 PHOTO SENSOR (P/N# PU60629) | |
JVC | HRD901U | N/A | DEAD - NO FUSES BLOWN | CHECK/REPLACE Q5 IN POWER SUPPLY (2SC1740S) | |
JVC | HRD910U | N/A | MANUAL AND AUTO CHANNEL SET DO NOT WORK | CHECK/REPLACE Q101 (P/N # 2SD1450S,T) IN TUNER CIRCUIT | |
JVC | HRD910U | N/A | NO POWER - NO DISPLAY - ALL FUSES OK | CHECK/REPLACE Q5 (P/N# 2SC1740S) | |
JVC | HRD910U | N/A | TUNER SKIPS CHANNELS WHILE SCANNING | CHECK/REPLACE IC702 (P/N# CAT93C46P) | |
JVC | HRD910U | N/A | AFTER SELECTING ANY FUNCTION, UNIT GOES TO THAT FUNCTION THEN RETURNS TO STOP AND SHUTS OFF | CHECK/REPLACE R8 THERMISTOR (P/N# NTH5D473KB) | |
JVC | HRD910U | N/A | DEAD SET - NO DISPLAY - DISCONNECTING DISPLAY HEATER, UNIT WILL OPERATE | CHECK/REPLACE C33 IN POWER SUPPLY CIRCUIT (120uF @ 6.3v) | |
JVC | HRD910U | N/A | WHITE SQUARE IN CENTER OF SCREEN - NO MENU FUNCTIONS | CHECK/REPLACE IC901 (P/N# M50554-262SP) | |
JVC | HRD910U | N/A | DEAD - NO FUSES BLOWN | CHECK/REPLACE Q5 IN POWER SUPPLY (2SC1740S) | |
JVC | HRD910U | N/A | PRESS PLAY,VCR MAY SHOW A NORMAL PICTURE,HALF PICTURE AND HALF SNOW OR ALL SNOW. PRESS STOP THEN PLAY, MAY WORK FINE. | CHECK/REPLACE C6 ON DRUM STATOR UNIT | |
JVC | HRD920U | N/A | DEAD SET - NO DISPLAY - DISCONNECTING DISPLAY HEATER, UNIT WILL OPERATE | CHECK/REPLACE C33 IN POWER SUPPLY CIRCUIT (120uF @ 6.3v) | |
JVC | HRD920U | N/A | NO POWER - NO DISPLAY - ALL FUSES OK | CHECK/REPLACE Q5 (P/N# 2SC1740S) | |
JVC | HRD920U | N/A | DEAD - NO FUSES BLOWN | CHECK/REPLACE Q5 IN POWER SUPPLY (2SC1740S) | |
JVC | HRD930U | N/A | DRUM MOTOR RUNS CONTINUOUSLY WHILE THE POWER IS ON | CHECK/REPLACE IC401 (P/N# HD49733ANT) | |
JVC | HRD930U | N/A | NO POWER - NO DISPLAY - ALL FUSES OK | CHECK/REPLACE Q5 (P/N# 2SC1740S) | |
JVC | HRD930U | N/A | DEAD - NO FUSES BLOWN | CHECK/REPLACE Q5 IN POWER SUPPLY (2SC1740S) | |
JVC | HRD930U | N/A | DEAD SET - NO DISPLAY - DISCONNECTING DISPLAY HEATER, UNIT WILL OPERATE | CHECK/REPLACE C33 IN POWER SUPPLY CIRCUIT (120uF @ 6.3v) | |
JVC | HRD930U | N/A | COLOR FADES IN PLAYBACK | CHECK/REPLACE IC401 (P/N# HD49733ANT) | |
JVC | HRD960U | N/A | DEAD SET - NO DISPLAY - DISCONNECTING DISPLAY HEATER, UNIT WILL OPERATE | CHECK/REPLACE C33 IN POWER SUPPLY CIRCUIT (120uF @ 6.3v) | |
JVC | HRD960U | N/A | DEAD - POWER SUPPLY CHIRPS OR SQUEALS | CHECK/REPLACE C9,C18,C21 AND C33 | |
JVC | HRD960U | N/A | DEAD - POWER SUPPLY CHIRPS OR SQUEALS | CHECK/REPLACE C9,C18,C21 AND C33 | |
JVC | HRD960U | N/A | NO DISPLAY UNIT WILL OPERATES OTHERWISE | CHECK/REPLACE R21 (47? | |
JVC | HRD970U | N/A | DEAD - POWER SUPPLY CHIRPS OR SQUEALS | CHECK/REPLACE C9,C18,C21 AND C33 | |
JVC | HRD970U | N/A | NO DISPLAY UNIT WILL OPERATES OTHERWISE | CHECK/REPLACE R21 (47? | |
JVC | HRD970U | N/A | NO E-E OR PLAYBACK VIDEO | CHECK/REPLACE L201 FOR OPEN (PU59153-101K) | |
JVC | HRD970U | N/A | DEAD SET - NO DISPLAY - DISCONNECTING DISPLAY HEATER, UNIT WILL OPERATE | CHECK/REPLACE C33 IN POWER SUPPLY CIRCUIT (120uF @ 6.3v) | |
JVC | HRDX20U | N/A | WON'T PLAYBACK COLOR IN SP MODE | CHECK/REPLACE IC2 (P/N# JCP002-2) ON VIDEO UNIT | |
JVC | HRDX20U | N/A | LOCKS UP IN THE AUTO-TUNE MODE | CHECK/REPLACE IC702 (CAT93C46P) | |
JVC | HRDX20U | N/A | AUDIO IS NOT MUTED IN THE FORWARD OR REVERSE SCAN MODES | CHECK/REPLACE IC601 (P/N# M37417M4-138SP) | |
JVC | HRDX20U | N/A | NO VIDEO RECORDED ON THE TAPE | CHECK/REPLACE IC601 (P/N# M37417M4-138SP) | |
JVC | HRDX20U | N/A | SYSTEM CONTROL HAS A MIND OF ITS OWN | CHECK/REPLACE CP401 | |
JVC | HRDX20U | N/A | CAPSTAN MOTOR DOES NOT RUN | CHECK/REPLACE C602 (100uF @ 6.3v) IN MECHACON CIRCUIT | |
JVC | HRDX40U | N/A | PRESS PLAY,VCR MAY SHOW A NORMAL PICTURE,HALF PICTURE AND HALF SNOW OR ALL SNOW. PRESS STOP THEN PLAY, MAY WORK FINE. | CHECK/REPLACE LOWER DRUM OR STATOR UNIT ON DRUM MOTOR | |
JVC | HRDX40U | N/A | UNIT DAMAGES TAPES IN REWIND-EJECT FUNCTION IS INTERMITTENT | CHECK/REPLACE MODE SELECT SWITCH (P/N# PU60622-1-1) | |
JVC | HRDX40U | N/A | LOCKS UP AND POWERS OFF WHEN LOADING THE TAPE | CHECK/REPLACE IC1 (BA6418N) | |
JVC | HRDX40U | N/A | EATS TAPE IN REVERSE SEARCH MODE | CHECK/REPLACE POLE BASE ASSEMBLY (P/N# PU61151-3) | |
JVC | HRDX40U | N/A | NO VIDEO RECORDED ON THE TAPE | CHECK/REPLACE IC601 (P/N# M37417M4-138SP) | |
JVC | HRDX40U | N/A | DRUM RUN TOO SLOW | CHECK/REPLACE D406 (P/N# RD5.1ES-T1B2) SERVO CIRCUIT | |
JVC | HRDX40U | N/A | AUDIO BUZZ DURING PLAYBACK | RELOCATE CABLE FROM CN201 AWAY FROM IC301 | |
JVC | HRDX40U | N/A | UNIT WILL LOAD TAPE BUT WON'T PLAY--WHEN EJECTED, IT EATS THE TAPE | CHECK/REPLACE CP401 (P/N# ICP-F15) | |
JVC | HRDX40U | N/A | CAPSTAN MOTOR RUNS SLOW AND VCR WILL NOT PAUSE | CHECK/REPLACE Q801 (2SC1740S) IN REGULATOR CIRCUIT | |
JVC | HRDX40U | N/A | ERASE TAPE IN THE PLAY MODE | CHECK/REPLACE IC301 (P/N # BA7765AS) | |
JVC | HRDX40U | N/A | ERASES TAPES IN THE PLAY MODE | CHECK/REPLACE IC601 (M37417M4-134SP) | |
JVC | HRDX40U | N/A | VCR ATTEMPTS TO LOAD OR EJECT WHEN THE POWER IS TURNED ON AND THEN SHUTS OFF | CHECK/REPLACE CP601 (P/N # ICP-F25) | |
JVC | HRDX42U | N/A | UNIT GOES TO PLAY WHEN EVER A TAPE IS LOADED REGARDLESS OF WHETHER THE ERASE PROTECT TAB IS PRESENT OR NOT | CHECK/REPLACE S2 (RECORD SAFTEY SWITCH) (P/N# PU60624-1-4) | |
JVC | HRDX62U | N/A | PICTURE MOVES FROM SIDE TO SIDE WHEN IN THE PAUSE OR SLOW MOTION MODES | CHECK/REPLACE C426 (P/N# QENC1HM-474) | |
JVC | HRDX62U | N/A | TAPE RUNS AT WRONG SPEED AND COUNTER MOVES WHEN TAPE IS STOPPED. | CHECK/REPLACE C12 (P/N# PU61024-826) | |
JVC | HRDX62U | N/A | UNIT WILL NOT RECORD AUDIO AND SCREEN APPEARS TO HAVE ALOT OF COLOR NOISE | CHECK/REPLACE Q301 (P/N# 2SC4081(RS) ) | |
JVC | HRDX62U | N/A | NO OUTPUT FROM TUNER BUT PLAYBACK IS OK | CHECK/REPLACE Q101 (P/N# 2SD2144) | |
JVC | HRFC100U | N/A | WHEN UNIT IS POWERED UP, IT WILL TRY TO LOAD WITH NO CASSETTE INSERTED. | CHECK/REPLACE IC1 (TC4512BP) ON DECK TERMINAL BOARD | |
JVC | HRFC100U | N/A | DEAD | CHECK/REPLACE D15 IN POWER SUPPLY - (15v ZENER) | |
JVC | HRFC100U | N/A | COUNTER DOESN'T WORK DURING FF OR REW | CHECK/ALIGN HALF LOADING GEAR ASSEMBLY FOR PROPER TAPE CONTACT TO AUDIO/CTRL HEAD. | |
JVC | HRFC100U | N/A | IN FORWARD OR REVERSE SEARCH, UNIT EATS TAPE AND THEN SHUTS OFF | CHECK/REPLACE GEAR UNIT ASSY. (P/N# PU61250-1-2) | |
JVC | HRIP820U | N/A | LOAD POST JAMS INTERMITTENTLY | CHECK/REPLACE LOAD POST (P/N# PQ46330A-3), TENSION ARM (PQ35012),LOADING ARM (PQ46337A-3), PLATE (PQ11658-1-15) | |
JVC | HRJ200U | N/A | TIMER RECORDING WILL NOT FUNCTION | CHECK/REPLACE IC601 (P/N# HD6433926A40F) | |
JVC | HRJ200U | N/A | INTERMITTENT WILL NOT LOAD CERTAIN TAPES | INSTALL KIT (P/N# PTU96115) | |
JVC | HRJ210U | N/A | POWER SUPPLY BUZZES WHEN UNIT IS PLUGGED IN | CHECK/REPLACE Q802 (P/N# 2SC3616(MLK) ), D860 (RD15ES-T1B1) AND D864 (P/N# HZ22CP) | |
JVC | HRJ220U | N/A | LOAD POST JAMS INTERMITTENTLY | CHECK/REPLACE LOAD POST (P/N# PQ46330A-3), TENSION ARM (PQ35012),LOADING ARM (PQ46337A-3), PLATE (PQ11658-1-15) | |
JVC | HRJ400U | N/A | UNIT SHUTS DOWN AFTER 15 SECONDS | CHECK/REPLACE Q804 (P/N# DTA114ES) ON REGULATOR BOARD | |
JVC | HRJ400U | N/A | TIMER RECORDING WILL NOT FUNCTION | CHECK/REPLACE IC601 (P/N# HD6433926A40F) | |
JVC | HRJ400U | N/A | NO AUDIO IN PLAYBACK OR E-E MODES | CHECK/REPLACE IC301 (P/N# XRA7790LS) | |
JVC | HRJ400U | N/A | NO VIDEO | CHECK/REPLACE Q204 (P/N# 2SA933S(RS) | |
JVC | HRJ400U | N/A | FLUORESCENT DISPLAY IS DARK | CHECK/REPLACE R32 (P/N # QRZ0077-101X) | |
JVC | HRJ400U | N/A | NO DISPLAY | CHECK/REPLACE R32 (P/N# QRZ0077-101X) ON REGULATOR BOARD | |
JVC | HRJ400U | N/A | INTERMITTENT WILL NOT LOAD CERTAIN TAPES | INSTALL KIT (P/N# PTU96115) | |
JVC | HRJ410U | N/A | DEAD - NO CLOCK OR ANY FUNCTION | CHECK/REPLACE CP851 - (ICP-N20) | |
JVC | HRJ410U | N/A | VIDEO INPUT ON FRONT OF VCR DOESN'T WORK WHEN IN THE AUX MODE | CHECK/REPLACE IC1 (P/N# JCP0035) | |
JVC | HRJ420U | N/A | LOAD POST JAMS INTERMITTENTLY | CHECK/REPLACE LOAD POST (P/N# PQ46330A-3), TENSION ARM (PQ35012),LOADING ARM (PQ46337A-3), PLATE (PQ11658-1-15) | |
JVC | HRJ420U | N/A | TRANSPORT LOCKS UP IN THE LOADED POSITION - UNIT POWERS UP BUT SHUTS OFF | CHECK/REPLACE IC1 (P/N# UPD16312GB(M) ) | |
JVC | HRJ600U | N/A | UNIT STUCK IN REWIND MODE | CHECK/REPLACE Q3 (P/N# PT491F) END SENSOR | |
JVC | HRJ600U | N/A | WILL NOT PLAYBACK HI-FI AUDIO | CHECK/REPLACE IC1001 (P/N# AN3380NK) | |
JVC | HRJ600U | N/A | INTERMITTENT WILL NOT LOAD CERTAIN TAPES | INSTALL KIT (P/N# PTU96115) | |
JVC | HRJ600U | N/A | VCR RUNS IN REVERSE AFTER CASSETTE IS LOADED AND ANY FUNCTION IS SELECTED | CHECK/REPLACE Q3 END SENSOR (P/N # PT491F) | |
JVC | HRJ600U | N/A | AFTER POWER IS TURNED ON ,ANY FUNCTION RESULTS IN UNIT GOING INTO REWIND MODE | CHECK/REPLACE END SENSOR (P/N# PT491F) | |
JVC | HRJ600U | N/A | TIMER RECORDING WILL NOT FUNCTION | CHECK/REPLACE IC601 (P/N# HD6433926A40F) | |
JVC | HRJ610U | N/A | PICTURE BENDS DURING PLAYBACK | CHECK/REPLACE C54 (P/N# QCFA1CZ-474) | |
JVC | HRJ620U | N/A | TAPE STUCK INSIDE AND WILL NOT EJECT | CHECK/REPLACE PINCH PLATE (P/N# PQ21685-1-4) | |
JVC | HRJ620U | N/A | POP IN THE AUDIO DURING CHANNEL CHANGE | CHECK/REPLACE IC1001 (P/N# JCP0056) | |
JVC | HRJ620U | N/A | LOAD POST JAMS INTERMITTENTLY | CHECK/REPLACE LOAD POST (P/N# PQ46330A-3), TENSION ARM (PQ35012),LOADING ARM (PQ46337A-3), PLATE (PQ11658-1-15) | |
JVC | HRJ621U | N/A | LOAD POST JAMS INTERMITTENTLY | CHECK/REPLACE LOAD POST (P/N# PQ46330A-3), TENSION ARM (PQ35012),LOADING ARM (PQ46337A-3), PLATE (PQ11658-1-15) | |
JVC | HRS4700U | N/A | NO EE VIDEO | CHECK/REPLACE IC1 (BA7649) ON VIDEO BOARD | |
JVC | HRS5000U | N/A | NO RECORD OR PLAYBACK IN THE S-VHS MODE - NORMAL MODE WORKS FINE | CHECK/REPLACE LPF103 ON MAIN PCB (P/N PU60097-2) | |
JVC | HRS5000U | N/A | NO SERVO LOCK - INTERMITTENT NOISE IN PLAYBACK | CHECK/REPLACE IC401 (HD49722NT) MAY BE THERMAL | |
JVC | HRS5500U | N/A | NO SERVO LOCK - INTERMITTENT NOISE IN PLAYBACK | CHECK/REPLACE IC401 (HD49722NT) MAY BE THERMAL | |
JVC | HRS5500U | N/A | NO RECORD OR PLAYBACK IN THE S-VHS MODE - NORMAL MODE WORKS FINE | CHECK/REPLACE LPF103 ON MAIN PCB (P/N PU60097-2) | |
JVC | HRS5800U | N/A | WILL NOT PLAYBACK STANDARD VHS BUT S-VHS IS GOOD | CHECK/REPLACE LPF505 FOR OPEN (PU60054-2) | |
JVC | HRS5800U | N/A | COLOR BEAT PATTERN AT THE BOTTOM OF PICTURE | ADD COIL (P/N# PU48530-561J) TO PIN 7 OF IC505 AND OTHER END TO A CAPACITOR (P/N# QFN31HJ-103) THEN GROUND CAPACITOR | |
JVC | HRS5800U | N/A | UNSTABLE PICTURE IN PLAYBACK MODE AND PICTURE IS DISTORTED IN REVERSE SEARCH | CHECK/REPLACE SUPPLY POLE BASE ASSY. (P/N# PU61151-2-6) | |
JVC | HRS5800U | N/A | UNIT LOADS THEN UNLOADS | CHECK HALF LOAD LEVER-REPLACE WITH GEAR KIT (PTU96031-690A) | |
JVC | HRS6600U | N/A | INTERMITTENTLY EATS TAPES ON REWIND AND FAST FORWARD SEARCH MODES | CHECK/REPLACE SMALL WHITE NYLON GEAR ON CAPSTAN MOTOR FOR CRACKS (P/N 61003-1-2) | |
JVC | HRS6600U | N/A | UNIT LOADS THEN UNLOADS | CHECK HALF LOAD LEVER-REPLACE WITH GEAR KIT (PTU96031-690A) | |
JVC | HRS6700U | N/A | VERY DIM DISPLAY | CHECK/REPLACE C14 (QEZ0156-127Z) AND C15 (QETC0JM-107) | |
JVC | HRS6800U | N/A | BLUE SCREEN IN THE PLAY MODE | CHECK/REPLACE Q41 (P/N # 2SC4081(QRS) ) ON PRE-RECORD BD. | |
JVC | HRS6900U | N/A | UNIT WILL NOT ACCEPT TAPE | CHECK/REPLACE CAPSTAN MOTOR (P/N# PU61313) | |
JVC | HRS6900U | N/A | BLACK PICTURE WITH WHITE DOTS WHEN DISPLAYING FAMILY MESSAGE OR MENU ON-SCREEN | CHECK/REPLACE X1 (P/N# PEVB0435) ON OSD BOARD | |
JVC | HRS6900U | N/A | IN TUNER MODE, UNIT DISPLAYS A GRID OF DOTS OVER THE DISPLAYED IMAGE AFTER THE UNIT WARMS UP. | CHECK/REPLACE IC2 (P/N# M35010-089SP) ON OSD BOARD | |
JVC | HRS7000U | N/A | PICTURE IS NORMAL BUT HAS ABNORMAL DISPLAY - PLAY,REC/PAUSE FAST FORWARD AND REWIND INDICATORS ARE ALL LIT AT ONCE. | CHECK/REPLACE IC2 AND CF2 ON THE RANDOM ACCESS PWB | |
JVC | HRS7000U | N/A | REWIND AND FAST FORWARD WORK OK BUT NO PLAY OR RECORD | CHECK/REPLACE D606 (1SS133) ON MECHACON BOARD | |
JVC | HRS7000U | N/A | NOISY PICTURE IN PLAYBACK (SERVO PROBLEMS) | CHECK/REPLACE IC403 AND IC501 ALSO CHECK CONNECTIONS ON CRYSTAL X1 ON MAIN PC BOARD. | |
JVC | HRSC1000U | N/A | NO AUDIO IN THE E-E OR PLAYBACK MODE | CHECK/REPLACE Q25 (P/N# 2SA854S(QR) ) | |
JVC | HRSC1000U | N/A | POOR TRACKING AND WOW AND FLUTTER BAD | CHECK/REPLACE D601 (P/N# 1SS133) | |
JVC | HRSC1000U | N/A | UNIT LOSES TIME SETTING IMMEDIATELY IF POWER IS LOST - SHOULD HOLD TIME FOR AT LEAST 1 MINUTE AFTER LOSS OF POWER | CHECK/REPLACE C3 ON TIMER BOARD (P/N# QEA40HZ-104) | |
JVC | HRVP404U | N/A | NO DISPLAY - UNIT IS DEAD | CHECK/REPLACE IC601 (P/N# HD6433926A03F) | |
JVC | HRVP404U | N/A | INTERMITTENT WILL NOT LOAD CERTAIN TAPES | INSTALL KIT (P/N# PTU96115) | |
JVC | HRVP404U | N/A | TIMER RECORDING WILL NOT FUNCTION | CHECK/REPLACE IC601 (P/N# HD6433927A42F) | |
JVC | HRVP412U | N/A | NO DISPLAY | CHECK/REPLACE D858 (P/N# 1SS133) | |
JVC | HRVP412U | N/A | NO E-E AUDIO OR VIDEO BUT TAPE PLAYS FINE | CHECK/REPLACE IC401 (P/N# HD49780NT) | |
JVC | HRVP412U | N/A | FRONT DISPLAY IS OUT | CHECK/REPLACE D862 (P/N# RD30ES-T1B1) | |
JVC | HRVP416U | N/A | DISTORTED HORZ. LINES MOVE ACROSS PICTURE | CHECK/REPLACE C810 (P/N# QETM2DM-826R) - REGULATOR BOARD | |
JVC | HRVP422U | N/A | LOAD POST JAMS INTERMITTENTLY | CHECK/REPLACE LOAD POST (P/N# PQ46330A-3), TENSION ARM (PQ35012),LOADING ARM (PQ46337A-3), PLATE (PQ11658-1-15) | |
JVC | HRVP434U | N/A | CABLE BOX EYE DOESN'T WORK | CN708 IS MIS-WIRED - IT SHOULD CONNECT TO PINS #3 & #4 AND NOT PINS #1 & #2 | |
JVC | HRVP436U | N/A | CABLE BOX EYE DOESN'T WORK | CN708 IS MIS-WIRED - IT SHOULD CONNECT TO PINS #3 & #4 AND NOT PINS #1 & #2 | |
JVC | HRVP55U | N/A | LOAD POST JAMS INTERMITTENTLY | CHECK/REPLACE LOAD POST (P/N# PQ46330A-3), TENSION ARM (PQ35012),LOADING ARM (PQ46337A-3), PLATE (PQ11658-1-15) | |
JVC | HRVP604U | N/A | TIMER RECORDING WILL NOT FUNCTION | CHECK/REPLACE IC601 (P/N# HD6433927A42F) | |
JVC | HRVP604U | N/A | INTERMITTENT WILL NOT LOAD CERTAIN TAPES | INSTALL KIT (P/N# PTU96115) | |
JVC | HRVP604U | N/A | LOUD BUZZ IN PLAYBACK AND E-E VIDEO - TAPES RECORDED ON THIS VCR PLAY OK IN ANOTHER VCR | CHECK/REPLACE IC601 (P/N# HD6433927A33) | |
JVC | HRVP604U | N/A | NO POWER - NO DISPLAY AND A HIGH PITCHED SQUEAL FROM POWER SUPPLY | CHECK/REPLACE C13 (P/N# QCZ0212-472) | |
JVC | HRVP606U | N/A | HEAD SWITCHING ADJUSTMENTS ARE NOT MEMORIZED | CHECK/REPLACE IC602 (P/N3 93C46/P) | |
JVC | HRVP606U | N/A | INTERMITTENT WILL NOT LOAD CERTAIN TAPES | INSTALL KIT (P/N# PTU96115) | |
JVC | HRVP606U | N/A | TIMER RECORDING WILL NOT FUNCTION | CHECK/REPLACE IC601 (P/N# HD6433927A42F) | |
JVC | HRVP606U | N/A | NO AUDIO IN E-E OR PLAYBACK MODES | CHECK/REPLACE Q302 (P/N# 2SC1740S(RS) ) | |
JVC | HRVP606U | N/A | NO AUDIO IN PLAYBACK MODE | CHECK/REPLACE Q301 (P/N# 2SC1740S(RS) ) | |
JVC | HRVP612U | N/A | PLAYBACK OF SELF RECORDED TAPES HAS A HORZ. LINE ACROSS THE SCREEN AT RANDOM LOCATIONS | CHECK/REPLACE IC401 (P/N# JCP0039) | |
JVC | HRVP612U | N/A | DRUM MOTOR RUNS ERRATICALLY OR WON'T START UP AT ALL | CHECK/REPLACE STATOR ASSEMBLY (P/N# PDZ0141) | |
JVC | HRVP624U | N/A | LOAD POST JAMS INTERMITTENTLY | CHECK/REPLACE LOAD POST (P/N# PQ46330A-3), TENSION ARM (PQ35012),LOADING ARM (PQ46337A-3), PLATE (PQ11658-1-15) | |
JVC | HRVP626U | N/A | LOAD POST JAMS INTERMITTENTLY | CHECK/REPLACE LOAD POST (P/N# PQ46330A-3), TENSION ARM (PQ35012),LOADING ARM (PQ46337A-3), PLATE (PQ11658-1-15) | |
JVC | HRVP627U | N/A | LOAD POST JAMS INTERMITTENTLY | CHECK/REPLACE LOAD POST (P/N# PQ46330A-3), TENSION ARM (PQ35012),LOADING ARM (PQ46337A-3), PLATE (PQ11658-1-15) | |
JVC | HRVP628U | N/A | LOAD POST JAMS INTERMITTENTLY | CHECK/REPLACE LOAD POST (P/N# PQ46330A-3), TENSION ARM (PQ35012),LOADING ARM (PQ46337A-3), PLATE (PQ11658-1-15) | |
JVC | HRVP634U | N/A | UNIT PLAYS OK FOR 5 SECONDS THEN SHUTS OFF | CHECK/REPLACE PS701 AND PS702 (P/N# PU61433) | |
JVC | HRVP66U | N/A | WILL NOT PLAY OR RECORD AND TAPE GETS EATEN WHEN EJECTING | CHECK/REPLACE Q6 (P/N# 2SC4081(QRS) ) ON VIDEO PWB | |
JVC | HRVP700U | N/A | TIMER RECORDING WILL NOT FUNCTION | CHECK/REPLACE IC601 (P/N# HD6433927A42F) | |
JVC | HRVP700U | N/A | INTERMITTENT WILL NOT LOAD CERTAIN TAPES | INSTALL KIT (P/N# PTU96115) | |
JVC | HRVP710U | N/A | NO OSD | CHECK/REPLACE IC901 (P/N# UPD6459CS-501) | |
JVC | HRVP710U | N/A | PLAYBACK ON EP IS DARK AND HAS A VERTICAL ROLL | CHECK/REPLACE C206 (P/N# QEKF0JM-476) | |
JVC | HRVP720U | N/A | WILL NOT ACCEPT TAPES | CHECK/REPLACE CAPSTAN MOTOR (P/N# PU61435) | |
JVC | HRVP720U | N/A | LOAD POST JAMS INTERMITTENTLY | CHECK/REPLACE LOAD POST (P/N# PQ46330A-3), TENSION ARM (PQ35012),LOADING ARM (PQ46337A-3), PLATE (PQ11658-1-15) | |
JVC | HRVP75U | N/A | LOAD POST JAMS INTERMITTENTLY | CHECK/REPLACE LOAD POST (P/N# PQ46330A-3), TENSION ARM (PQ35012),LOADING ARM (PQ46337A-3), PLATE (PQ11658-1-15) | |
JVC | HRVP81U | N/A | LOAD POST JAMS INTERMITTENTLY | CHECK/REPLACE LOAD POST (P/N# PQ46330A-3), TENSION ARM (PQ35012),LOADING ARM (PQ46337A-3), PLATE (PQ11658-1-15) | |
JVC | SR3250U | N/A | WHEN PLAYING BACK A PRE-RECORDED TAPE, THE UNIT ERASES TAPE | CHECK/REPLACE Q606 (P/N# DTC143EU) | |
KMC | KMV15SH | N/A | PLAYBACK LED ON CONTINUOUSLY-NO TUNER OPERATION-NO E-E OR V-V SWITCHING- STUCK IN V-V MODE | CHECK/REPLACE IC802 (IR2403) | |
KMC | KMV15SH | N/A | GOES TO STOP MODE AFTER 5-10 SECONDS IN ALL MODES | CHECK IC802 AND CHANGE R816 TO A 56k | |
LLOYDS | L824 | N/A | NO SPEED SELECT ON ON PLAYBACK OR RECORD | REPLACE DEFECTIVE IC (BA718) ECG1529 | |
LLOYDS | L838 | N/A | NO SOUND | R528 OPEN,C516,IC502,IC501 | |
MAGNAVOX | CR9860 | N/A | BLOWS AC LINE FUSE IMMEDIATELY | CHECK F1001,D1001,C1004,Q1001,Q1002,D1015,D1005 | |
MAGNAVOX | CR9860 | N/A | WILL NOT REWIND AND EATS TAPES ON PLAYBACK | EXAMINE THE GEAR DIRECTLY BELOW MAIN DRIVE PULLEY. THIS IS ITEM# 141 ON THE BREAK DOWN. | |
MAGNAVOX | CR9860 | N/A | ONLY REWINDS WHEN POWERED UP | CHECK FOR OPEN SOLENOID (PS00029) | |
MAGNAVOX | CR9860 | N/A | BREAK LIFTER ARM WHEN UNLOADING | CHECK FOR BENT METAL TAPE FLAP OPENER (RIGHT FRONT | |
MAGNAVOX | CR9863 | N/A | WILL NOT REWIND AND EATS TAPES ON PLAYBACK | EXAMINE THE GEAR DIRECTLY BELOW MAIN DRIVE PULLEY. THIS IS ITEM# 141 ON THE BREAK DOWN. | |
MAGNAVOX | CR9863 | N/A | BREAK LIFTER ARM WHEN UNLOADING | CHECK FOR BENT METAL TAPE FLAP OPENER (RIGHT FRONT | |
MAGNAVOX | CR9863 | N/A | ONLY REWINDS WHEN POWERED UP | CHECK FOR OPEN SOLENOID (PS00029) | |
MAGNAVOX | CR9863 | N/A | BLOWS AC LINE FUSE IMMEDIATELY | CHECK F1001,D1001,C1004,Q1001,Q1002,D1015,D1005 | |
MAGNAVOX | CV1040 | N/A | ONLY A BLUE SCREEN IS RECORDED ON A TIMED RECORDING OF A HRC CABLE SIGNAL | CHANGE C667 TO A 2.2uF @ 50V | |
MAGNAVOX | P962 | N/A | TICKING OR BUZZING SOUND DURING FF/REW | INSTALL SPACER KIT (P/N# 483531057424) | |
MAGNAVOX | P964 | N/A | TICKING OR BUZZING SOUND DURING FF/REW | INSTALL SPACER KIT (P/N# 483531057424) | |
MAGNAVOX | P966 | N/A | TICKING OR BUZZING SOUND DURING FF/REW | INSTALL SPACER KIT (P/N# 483531057424) | |
MAGNAVOX | VCT425AT | N/A | WHITE RANDOM STATIC NOISE IN THE PICTURE AND/OR RANDOM STATIC IN HIFI AUDIO - INTERMITTENT PROBLEM | CHECK/REPL. GROUNDING BRUSH ON THE DRUM (P/N# 483531057378) | |
MAGNAVOX | VCT445AT | N/A | WHITE RANDOM STATIC NOISE IN THE PICTURE AND/OR RANDOM STATIC IN HIFI AUDIO - INTERMITTENT PROBLEM | CHECK/REPL. GROUNDING BRUSH ON THE DRUM (P/N# 483531057378) | |
MAGNAVOX | VPT200 | N/A | LED PRISM IS BROKEN | CHECK/REPLACE REF# 035 (P/N# 483513087134) | |
MAGNAVOX | VPT205 | N/A | LED PRISM IS BROKEN | CHECK/REPLACE REF# 035 (P/N# 483513087134) | |
MAGNAVOX | VPT210 | N/A | POWER SUPPLY FAILS WHEN UNIT IS PLUGGED IN | CHECK/RESOLDER CONNECTIONS ON IC1002 (CHECK TO MAKE SURE THE RACK ASSY. ISN'T HITTING IC1002 CAUSING PROBLEM) | |
MAGNAVOX | VPT210 | N/A | POWER SUPPLY FAILS WHEN UNIT IS PLUGGED INTO AC | CHECK/RESOLDER CONNECTIONS ON IC1002 | |
MAGNAVOX | VPT215 | N/A | POWER SUPPLY FAILS WHEN UNIT IS PLUGGED INTO AC | CHECK/RESOLDER CONNECTIONS ON IC1002 | |
MAGNAVOX | VPT215 | N/A | POWER SUPPLY FAILS WHEN UNIT IS PLUGGED IN | CHECK/RESOLDER CONNECTIONS ON IC1002 (CHECK TO MAKE SURE THE RACK ASSY. ISN'T HITTING IC1002 CAUSING PROBLEM) | |
MAGNAVOX | VPU210 | N/A | MECHANISM LOCKS UP - USUALLY AT THE END OF THE REWIND AND UNIT SHUTS OFF WITH TAPE STUCK | REF# B81 LEVER LACKS LUBRICATION AND STICKS - APPLY MOLYTONE GREASE (P/N# 483531057035) | |
MAGNAVOX | VPU215 | N/A | MECHANISM LOCKS UP - USUALLY AT THE END OF THE REWIND AND UNIT SHUTS OFF WITH TAPE STUCK | REF# B81 LEVER LACKS LUBRICATION AND STICKS - APPLY MOLYTONE GREASE (P/N# 483531057035) | |
MAGNAVOX | VR1225 | N/A | INTERMITTENTLY GOES TO BLUE SCRN.--REW/FF SCAN PIX IS OK | CHECK FOR DEFECTIVE C2014 OR C2015 OR SOLDER CONNECTIONS ON EITHER. | |
MAGNAVOX | VR1225 | N/A | MULTIPLE SOLENOID FAILURES | REMOVE JUMPER AT C6001 AND INSTALL KIT# 483531057044 | |
MAGNAVOX | VR1225 | N/A | WILL NOT REWIND AND EATS TAPES ON PLAYBACK | EXAMINE THE GEAR DIRECTLY BELOW MAIN DRIVE PULLEY. THIS IS ITEM# 141 ON THE BREAK DOWN. | |
MAGNAVOX | VR1225 | N/A | ERRATIC OPERATION-LOADS TAPE IN VCR THEN NOTHING-MAY BEGIN TO PLAY TAPE AND JUST STOP BUT STAYS LOADED | CHECK/REPLACE MODE SWITCH ON RIGHT SIDE OF CASSETTE HOUSING AND HARD WIRE 4 WIRE PLUG CONNECTION. | |
MAGNAVOX | VR1260 | N/A | ERRATIC OPERATION-LOADS TAPE IN VCR THEN NOTHING-MAY BEGIN TO PLAY TAPE AND JUST STOP BUT STAYS LOADED | CHECK/REPLACE MODE SWITCH ON RIGHT SIDE OF CASSETTE HOUSING AND HARD WIRE 4 WIRE PLUG CONNECTION. | |
MAGNAVOX | VR1260 | N/A | WILL NOT REWIND AND EATS TAPES ON PLAYBACK | EXAMINE THE GEAR DIRECTLY BELOW MAIN DRIVE PULLEY. THIS IS ITEM# 141 ON THE BREAK DOWN. | |
MAGNAVOX | VR1260 | N/A | INTERMITTENTLY GOES TO BLUE SCRN.--REW/FF SCAN PIX IS OK | CHECK FOR DEFECTIVE C2014 OR C2015 OR SOLDER CONNECTIONS ON EITHER. | |
MAGNAVOX | VR1260 | N/A | MULTIPLE SOLENOID FAILURES | REMOVE JUMPER AT C6001 AND INSTALL KIT# 483531057044 | |
MAGNAVOX | VR1820 | N/A | WILL NOT REWIND AND EATS TAPES ON PLAYBACK | EXAMINE THE GEAR DIRECTLY BELOW MAIN DRIVE PULLEY. THIS IS ITEM# 141 ON THE BREAK DOWN. | |
MAGNAVOX | VR1820 | N/A | ONLY REWINDS WHEN POWERED UP | CHECK FOR OPEN SOLENOID (PS00029) | |
MAGNAVOX | VR1820 | N/A | BLOWS AC LINE FUSE IMMEDIATELY | CHECK F1001,D1001,C1004,Q1001,Q1002,D1015,D1005 | |
MAGNAVOX | VR1820 | N/A | ERRATIC OPERATION-LOADS TAPE IN VCR THEN NOTHING-MAY BEGIN TO PLAY TAPE AND JUST STOP BUT STAYS LOADED | CHECK/REPLACE MODE SWITCH ON RIGHT SIDE OF CASSETTE HOUSING AND HARD WIRE 4 WIRE PLUG CONNECTION. | |
MAGNAVOX | VR1820 | N/A | BREAK LIFTER ARM WHEN UNLOADING | CHECK FOR BENT METAL TAPE FLAP OPENER (RIGHT FRONT | |
MAGNAVOX | VR1830 | N/A | ONLY REWINDS WHEN POWERED UP | CHECK FOR OPEN SOLENOID (PS00029) | |
MAGNAVOX | VR1830 | N/A | BREAK LIFTER ARM WHEN UNLOADING | CHECK FOR BENT METAL TAPE FLAP OPENER (RIGHT FRONT | |
MAGNAVOX | VR1830 | N/A | BLOWS AC LINE FUSE IMMEDIATELY | CHECK F1001,D1001,C1004,Q1001,Q1002,D1015,D1005 | |
MAGNAVOX | VR1830 | N/A | WILL NOT REWIND AND EATS TAPES ON PLAYBACK | EXAMINE THE GEAR DIRECTLY BELOW MAIN DRIVE PULLEY. THIS IS ITEM# 141 ON THE BREAK DOWN. | |
MAGNAVOX | VR1830 | N/A | ERRATIC OPERATION-LOADS TAPE IN VCR THEN NOTHING-MAY BEGIN TO PLAY TAPE AND JUST STOP BUT STAYS LOADED | CHECK/REPLACE MODE SWITCH ON RIGHT SIDE OF CASSETTE HOUSING AND HARD WIRE 4 WIRE PLUG CONNECTION. | |
MAGNAVOX | VR1835 | N/A | UNIT IS DEAD - F2 AND CP401 MAY BE OPEN | CHECK LEADS OF C425 FOR POSSIBLE SHORT - REPLACE F2 & CP401 | |
MAGNAVOX | VR1835 | N/A | DAY ADVANCES WHEN REVIEWING TIMER RECORDING SETTINGS | THIS IS A SOFTWARE PROBLEM AND WILL NOT AFFECT OPERATION BECAUSE ONLY THE DAY IS ADVANCED AND NOT THE DATE | |
MAGNAVOX | VR1840 | N/A | WILL NOT REWIND AND EATS TAPES ON PLAYBACK | EXAMINE THE GEAR DIRECTLY BELOW MAIN DRIVE PULLEY. THIS IS ITEM# 141 ON THE BREAK DOWN. | |
MAGNAVOX | VR1840 | N/A | ONLY REWINDS WHEN POWERED UP | CHECK FOR OPEN SOLENOID (PS00029) | |
MAGNAVOX | VR1840 | N/A | BLOWS AC LINE FUSE IMMEDIATELY | CHECK F1001,D1001,C1004,Q1001,Q1002,D1015,D1005 | |
MAGNAVOX | VR1840 | N/A | BREAK LIFTER ARM WHEN UNLOADING | CHECK FOR BENT METAL TAPE FLAP OPENER (RIGHT FRONT | |
MAGNAVOX | VR1840 | N/A | ERRATIC OPERATION-LOADS TAPE IN VCR THEN NOTHING-MAY BEGIN TO PLAY TAPE AND JUST STOP BUT STAYS LOADED | CHECK/REPLACE MODE SWITCH ON RIGHT SIDE OF CASSETTE HOUSING AND HARD WIRE 4 WIRE PLUG CONNECTION. | |
MAGNAVOX | VR2032 | N/A | BLOWS AC LINE FUSE IMMEDIATELY | CHECK F1001,D1001,C1004,Q1001,Q1002,D1015,D1005 | |
MAGNAVOX | VR2032 | N/A | ONLY REWINDS WHEN POWERED UP | CHECK FOR OPEN SOLENOID (PS00029) | |
MAGNAVOX | VR2032 | N/A | WILL NOT ACCEPT TAPE--TIMING IS OK | CHECK R674 (1 OHM) FOR OPEN | |
MAGNAVOX | VR2032 | N/A | ERRATIC OPERATION-LOADS TAPE IN VCR THEN NOTHING-MAY BEGIN TO PLAY TAPE AND JUST STOP BUT STAYS LOADED | CHECK/REPLACE MODE SWITCH ON RIGHT SIDE OF CASSETTE HOUSING AND HARD WIRE 4 WIRE PLUG CONNECTION. | |
MAGNAVOX | VR2032 | N/A | WON'T LOAD - CAPSTAN WILL NOT RUN | CHECK/REPLACE R674 (1 OHM FUSIBLE) | |
MAGNAVOX | VR2032 | N/A | BREAK LIFTER ARM WHEN UNLOADING | CHECK FOR BENT METAL TAPE FLAP OPENER (RIGHT FRONT | |
MAGNAVOX | VR2032 | N/A | WILL NOT REWIND AND EATS TAPES ON PLAYBACK | EXAMINE THE GEAR DIRECTLY BELOW MAIN DRIVE PULLEY. THIS IS ITEM# 141 ON THE BREAK DOWN. | |
MAGNAVOX | VR2040 | N/A | HIGH PITCHED SQUEAL FROM CHASSIS | REPLACE IC11 (OPTO-COUPLER) | |
MAGNAVOX | VR2040 | N/A | ERRATIC OPERATION-LOADS TAPE IN VCR THEN NOTHING-MAY BEGIN TO PLAY TAPE AND JUST STOP BUT STAYS LOADED | CHECK/REPLACE MODE SWITCH ON RIGHT SIDE OF CASSETTE HOUSING AND HARD WIRE 4 WIRE PLUG CONNECTION. | |
MAGNAVOX | VR2040 | N/A | BREAK LIFTER ARM WHEN UNLOADING | CHECK FOR BENT METAL TAPE FLAP OPENER (RIGHT FRONT | |
MAGNAVOX | VR2040 | N/A | ONLY REWINDS WHEN POWERED UP | CHECK FOR OPEN SOLENOID (PS00029) | |
MAGNAVOX | VR2040 | N/A | BLOWS AC LINE FUSE IMMEDIATELY | CHECK F1001,D1001,C1004,Q1001,Q1002,D1015,D1005 | |
MAGNAVOX | VR2042 | N/A | WILL NOT REWIND AND EATS TAPES ON PLAYBACK | EXAMINE THE GEAR DIRECTLY BELOW MAIN DRIVE PULLEY. THIS IS ITEM# 141 ON THE BREAK DOWN. | |
MAGNAVOX | VR2042 | N/A | BREAK LIFTER ARM WHEN UNLOADING | CHECK FOR BENT METAL TAPE FLAP OPENER (RIGHT FRONT | |
MAGNAVOX | VR2042 | N/A | ONLY REWINDS WHEN POWERED UP | CHECK FOR OPEN SOLENOID (PS00029) | |
MAGNAVOX | VR2042 | N/A | BLOWS AC LINE FUSE IMMEDIATELY | CHECK F1001,D1001,C1004,Q1001,Q1002,D1015,D1005 | |
MAGNAVOX | VR2042 | N/A | ERRATIC OPERATION-LOADS TAPE IN VCR THEN NOTHING-MAY BEGIN TO PLAY TAPE AND JUST STOP BUT STAYS LOADED | CHECK/REPLACE MODE SWITCH ON RIGHT SIDE OF CASSETTE HOUSING AND HARD WIRE 4 WIRE PLUG CONNECTION. | |
MAGNAVOX | VR2050 | N/A | ERRATIC OPERATION-LOADS TAPE IN VCR THEN NOTHING-MAY BEGIN TO PLAY TAPE AND JUST STOP BUT STAYS LOADED | CHECK/REPLACE MODE SWITCH ON RIGHT SIDE OF CASSETTE HOUSING AND HARD WIRE 4 WIRE PLUG CONNECTION. | |
MAGNAVOX | VR2050 | N/A | BREAK LIFTER ARM WHEN UNLOADING | CHECK FOR BENT METAL TAPE FLAP OPENER (RIGHT FRONT | |
MAGNAVOX | VR2050 | N/A | BLOWS AC LINE FUSE IMMEDIATELY | CHECK F1001,D1001,C1004,Q1001,Q1002,D1015,D1005 | |
MAGNAVOX | VR2050 | N/A | WILL NOT REWIND AND EATS TAPES ON PLAYBACK | EXAMINE THE GEAR DIRECTLY BELOW MAIN DRIVE PULLEY. THIS IS ITEM# 141 ON THE BREAK DOWN. | |
MAGNAVOX | VR2050 | N/A | ONLY REWINDS WHEN POWERED UP | CHECK FOR OPEN SOLENOID (PS00029) | |
MAGNAVOX | VR2060 | N/A | BREAK LIFTER ARM WHEN UNLOADING | CHECK FOR BENT METAL TAPE FLAP OPENER (RIGHT FRONT | |
MAGNAVOX | VR2060 | N/A | ONLY REWINDS WHEN POWERED UP | CHECK FOR OPEN SOLENOID (PS00029) | |
MAGNAVOX | VR2060 | N/A | BLOWS AC LINE FUSE IMMEDIATELY | CHECK F1001,D1001,C1004,Q1001,Q1002,D1015,D1005 | |
MAGNAVOX | VR2060 | N/A | ERRATIC OPERATION-LOADS TAPE IN VCR THEN NOTHING-MAY BEGIN TO PLAY TAPE AND JUST STOP BUT STAYS LOADED | CHECK/REPLACE MODE SWITCH ON RIGHT SIDE OF CASSETTE HOUSING AND HARD WIRE 4 WIRE PLUG CONNECTION. | |
MAGNAVOX | VR2072 | N/A | DISPLAY PULSATES WHEN POWER SUPPLY HAS A LOAD ON IT | CHECK/REPLACE C121 AND C122 | |
MAGNAVOX | VR2072 | N/A | ERRATIC OPERATION-LOADS TAPE IN VCR THEN NOTHING-MAY BEGIN TO PLAY TAPE AND JUST STOP BUT STAYS LOADED | CHECK/REPLACE MODE SWITCH ON RIGHT SIDE OF CASSETTE HOUSING AND HARD WIRE 4 WIRE PLUG CONNECTION. | |
MAGNAVOX | VR2072 | N/A | WILL NOT REWIND AND EATS TAPES ON PLAYBACK | EXAMINE THE GEAR DIRECTLY BELOW MAIN DRIVE PULLEY. THIS IS ITEM# 141 ON THE BREAK DOWN. | |
MAGNAVOX | VR2072 | N/A | ONLY REWINDS WHEN POWERED UP | CHECK FOR OPEN SOLENOID (PS00029) | |
MAGNAVOX | VR2072 | N/A | BLOWS AC LINE FUSE IMMEDIATELY | CHECK F1001,D1001,C1004,Q1001,Q1002,D1015,D1005 | |
MAGNAVOX | VR2072 | N/A | BREAK LIFTER ARM WHEN UNLOADING | CHECK FOR BENT METAL TAPE FLAP OPENER (RIGHT FRONT | |
MAGNAVOX | VR3210 | N/A | ERRATIC OPERATION-LOADS TAPE IN VCR THEN NOTHING-MAY BEGIN TO PLAY TAPE AND JUST STOP BUT STAYS LOADED | CHECK/REPLACE MODE SWITCH ON RIGHT SIDE OF CASSETTE HOUSING AND HARD WIRE 4 WIRE PLUG CONNECTION. | |
MAGNAVOX | VR3210 | N/A | ERRATIC OPERATION-LOADS TAPE IN VCR THEN NOTHING-MAY BEGIN TO PLAY TAPE AND JUST STOP BUT STAYS LOADED | CHECK/REPLACE MODE SWITCH ON RIGHT SIDE OF CASSETTE HOUSING AND HARD WIRE 4 WIRE PLUG CONNECTION. | |
MAGNAVOX | VR3210 | N/A | WILL NOT REWIND AND EATS TAPES ON PLAYBACK | EXAMINE THE GEAR DIRECTLY BELOW MAIN DRIVE PULLEY. THIS IS ITEM# 141 ON THE BREAK DOWN. | |
MAGNAVOX | VR3210 | N/A | NO PIX OUT OF THE RF MODULATOR--VIDEO/AUDIO OUTPUTS OK | CHECK ALL SURFACE MOUNT DIODE INSIDE RF CONVERTER | |
MAGNAVOX | VR3210 | N/A | BLOWS AC LINE FUSE IMMEDIATELY | CHECK F1001,D1001,C1004,Q1001,Q1002,D1015,D1005 | |
MAGNAVOX | VR3210 | N/A | ONLY REWINDS WHEN POWERED UP | CHECK FOR OPEN SOLENOID (PS00029) | |
MAGNAVOX | VR3210 | N/A | BREAK LIFTER ARM WHEN UNLOADING | CHECK FOR BENT METAL TAPE FLAP OPENER (RIGHT FRONT | |
MAGNAVOX | VR3210 | N/A | WILL NOT REWIND AND EATS TAPES ON PLAYBACK | EXAMINE THE GEAR DIRECTLY BELOW MAIN DRIVE PULLEY. THIS IS ITEM# 141 ON THE BREAK DOWN. | |
MAGNAVOX | VR3213 | N/A | NO REWIND FUNCTION | CHECK/REPLACE RUBBER BUMPER ON DECK ASSY. (ITEM 41 ON DECK 3 EXPLODED VIEW) P/N# 483546667013 | |
MAGNAVOX | VR3223 | N/A | NO REWIND FUNCTION | CHECK/REPLACE RUBBER BUMPER ON DECK ASSY. (ITEM 41 ON DECK 3 EXPLODED VIEW) P/N# 483546667013 | |
MAGNAVOX | VR3330 | N/A | DEAD SET | CHECK/REPLACE D1007 (ECG587), Q1001 (2SC4418) AND Q1002 (2SD1458) | |
MAGNAVOX | VR3410 | N/A | NO VIDEO ON TAPE OR TUNER THRU RF OUTPUT BUT RCA JACK OUTPUTS WERE NORMAL | CHECK/REPLACE Q7001 AND Q7003 FOR SHORT | |
MAGNAVOX | VR3440 | N/A | INCORRECT YEAR IS DISPLAYED WHEN PROGRAMMED TIMER SETTINGS ARE REVIEWED | CHECK/REPLACE IC701 WITH NEW TYPE (P/N# 483520988149) | |
MAGNAVOX | VR3460 | N/A | REWIND MODE NOT DISPLAYED IN OSD | CHECK/REPLACE IC6K (P/N# 483520917366) | |
MAGNAVOX | VR3460 | N/A | DEAD - NO BLOWN FUSES | CHECK/REPLACE C107 (4.7uF @ 250v) AND C128 (470uF @ 25v) | |
MAGNAVOX | VR3460 | N/A | TAKES TAPE IN, AND TAPE BOUNCES UP/DOWN - (LOAD-UNLOAD) - WILL EVENTUALLY PLAY IF MESSED WITH - RELAY MAY CHATTER | CHECK/REPLACE C128 IN POWER SUPPLY | |
MAGNAVOX | VR3560 | N/A | TIMER WILL NOT PERFORM A NEXT DAY UP TO A 1 YEAR PROGRAMMED RECORDING DURING THE MONTHS OF OCT.,NOV., AND DEC. | CHECK/REPLACE IC6K WITH NEW TYPE (P/N# 483520917471) | |
MAGNAVOX | VR6065 | N/A | NO AUDIO ON TAPES RECORDED ON HITACHI VCR'S OR INTERMITTENT BLUE SCREEN | CHANGE R232 TO 33k, C211 TO 0.1uF, ADD A 0.1uF BETWEEN THE JUNCTION OF R232,R233,R231 TO THE GROUND SIDE OF C211 | |
MAGNAVOX | VR6065 | N/A | E-E MODE (PLAYBACK) INSTABILITY - MAY BE SEVERE ON SOME RENTAL TAPES | CHANGE C326 TO 100uF @ 16v,PARALLEL C326 WITH A 330k,ALSO PARALLEL C326 WITH A 0.01uF CERAMIC |
LAMSON
Digital Electronics Address: 1324-1326 Jose Abad Santos Ave.,Manila, Philippines TEL:00632-2559675 TEL/FAX:00632-2568130 Cellular:0922-8867809 0922-8867810 E-mail:[email protected]
YAHOO MESSENGER ID : myrna_q_ng or saishu_ng (old) Lamson Importers & Exporters Trading <We will not be
using the old address and phone no. in the future. Please be
noted when calling us, sending letters, parcels or buying our products>
|